Re: [gentoo-amd64] network services start problems

[Nadav Horesh]

On Mon, 2009-01-12 at 22:01 +0100, Beso wrote:
> 2009/1/12 Nadav Horesh <nadavh@×××××××××××.com>:
> > It is a desktop. I do not know how netplugd poped in, I do not see it in rc-update -s.
> > Is this may my the source of my problem?
> >
> maybe it's a dep of some other service.
  How can I test it?
>
 <> ----- -----
 <> : Sebastian Redl [mailto:sebastian.redl@×××××××××××.at]
 <> :  12--09 17:24
 <> : gentoo-amd64@l.g.o
 <> : Re: [gentoo-amd64] network services start problems
> >
> >
> > On Mon, 12 Jan 2009 14:27:31 +0200, Nadav Horesh <nadavh@×××××××××××.com>
> > wrote:
> >> The file /etc/conf.d/net is basically empty (only comments)
> >>
> >>>>From /var/log/messages:
> >>
> >> Jan 12 14:07:54 nadav 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1)
> >> 00:16:76:b9:00:76
> >> Jan 12 14:07:54 nadav 0000:00:19.0: eth0: Intel(R) PRO/1000 Network
> >> Connection
> >> Jan 12 14:07:54 nadav 0000:00:19.0: eth0: MAC: 4, PHY: 6, PBA No:
> >> ffffff-0ff
> >> Jan 12 14:07:57 nadav rc-scripts: WARNING:  netmount is scheduled to
> >> start when net.eth0 has started.
> >> Jan 12 14:07:58 nadav 0000:00:19.0: eth0: Link is Up 100 Mbps Full
> >> Duplex, Flow Control: RX/TX
> >> Jan 12 14:07:58 nadav 0000:00:19.0: eth0: 10/100 speed: disabling TSO
> >> Jan 12 14:07:58 nadav netplugd[7904]: eth0: state DOWN flags 0x00001003
> >> UP,BROADCAST,MULTICAST -> 0x00011043
> >> UP,BROADCAST,RUNNING,MULTICAST,10000
> >> Jan 12 14:07:58 nadav netplugd[8047]: /etc/netplug.d/netplug eth0 in ->
> >> pid 8047
> >> Jan 12 14:07:58 nadav netplugd[7904]: eth0: state INNING pid 8047 exited
> >> status 256
> >> Jan 12 14:08:03 nadav rc-scripts: WARNING:  dhcdbd is scheduled to start
> >> when net.eth0 has started.
> >> Jan 12 14:08:03 nadav rc-scripts: WARNING:  samba is scheduled to start
> >> when net.eth0 has started.
> >> Jan 12 14:08:09 nadav eth0: no IPv6 routers present
> >>
> >>  The last line points at what Sebastian indicated
> >>
> >
> > Actually, I just realized that what I said was absolute nonsense. Of course
> > you don't have an IPv4 address if DHCP won't run. *slaps forehead*
> >
> do you eth modules load before starting eth?! from your rc-update it
> seems so, but it this really true?
> i don't remember if starting the service manually would work. i
> immagine so. am i right?
>
I do not know how to answer these questions. Any hint?

  Nadav.