1 |
I had same problems with livecd. I know this might not help, but I just |
2 |
tried a daily debian etch and got this: |
3 |
|
4 |
TST 11FD: CPU1 testing scratch RAM system state word |
5 |
INI 10FC: CPU0 synchronizing |
6 |
INI 11FC: CPU1 synchronizing |
7 |
INI C100: CPU0 selected as monarch |
8 |
INI CC11: CPU1 early rendezvous |
9 |
TST 3000: verifying ROM checksum |
10 |
INI 3000: ROM checksum ok |
11 |
TST 3001: PDH control test |
12 |
INI 3001: PDH control init |
13 |
TST 3002: scratch RAM test |
14 |
TST 30BC: test system clocks |
15 |
INI 30BC: initialize system clocks |
16 |
INI CC21: CPU1 rendezvous |
17 |
INI C4CC: initialize close console |
18 |
INI C4CD: close console not found |
19 |
INI 3002: scratch RAM ok |
20 |
INI CC21: CPU1 rendezvous |
21 |
INI C30C: monarch slave check |
22 |
INI 10CA: CPU0 initialize system bus arbitration |
23 |
INI C300: early monarch0 selftest |
24 |
INI D000: micro controller interface test |
25 |
INI D005: setting domain1 fan speeds |
26 |
INI D006: setting domain2 fan speeds |
27 |
TST 1030: CPU0 start early selftests |
28 |
WRN 1031: CPU0 early selftests skipped |
29 |
INI 103C: CPU0 initialize |
30 |
TST 103E: CPU0 exit early selftests |
31 |
TST 1130: CPU1 start early selftests |
32 |
INI C30C: monarch slave check |
33 |
WRN 1131: CPU1 early selftests skipped |
34 |
INI 113C: CPU1 initialize |
35 |
TST 113E: CPU1 exit early selftests |
36 |
INI CC21: CPU1 rendezvous |
37 |
INI 10CA: CPU0 initialize system bus arbitration |
38 |
INI CC31: CPU1 cache rendezvous |
39 |
INI C30C: monarch slave check |
40 |
INI 10CA: CPU0 initialize system bus arbitration |
41 |
INI 7000: start memory DIMM scan |
42 |
INI 7500: memory reset |
43 |
INI 7002: initialize memory tables |
44 |
WRN 7101: memory register test skipped |
45 |
INI 7200: starting memory DIMM detection |
46 |
INI 7201: memory DIMM detection 0% complete |
47 |
INI 7210: is DIMM 00 installed? |
48 |
INI 7260: 1GB DIMM in memory slot 00 |
49 |
INI 7201: memory DIMM detection 12% complete |
50 |
INI 7211: is DIMM 01 installed? |
51 |
INI 7201: memory DIMM detection 25% complete |
52 |
INI 7212: is DIMM 02 installed? |
53 |
INI 7201: memory DIMM detection 37% complete |
54 |
INI 7213: is DIMM 03 installed? |
55 |
INI 7201: memory DIMM detection 50% complete |
56 |
INI 7214: is DIMM 04 installed? |
57 |
INI 7201: memory DIMM detection 62% complete |
58 |
INI 7215: is DIMM 05 installed? |
59 |
INI 7201: memory DIMM detection 75% complete |
60 |
INI 7216: is DIMM 06 installed? |
61 |
INI 7201: memory DIMM detection 87% complete |
62 |
INI 7217: is DIMM 07 installed? |
63 |
INI 7201: memory DIMM detection 100% complete |
64 |
TST 7010: start memory DIMM order check |
65 |
TST 7016: start memory DIMM pair loading check |
66 |
TST 7020: search for initial memory bank |
67 |
TST 7030: verify DIMM 00 still works as initial memory module |
68 |
INI 7307: generate memory interleave |
69 |
TST 7600: destructive memory test |
70 |
TST 7602: destructively test first page of memory |
71 |
TST 7604: starting 1st pass of memory test |
72 |
TST 7606: starting 2nd pass of memory test |
73 |
TST 7608: starting 3rd pass of memory test |
74 |
TST 7603: destructively testing the rest of memory |
75 |
TST 7604: starting 1st pass of memory test |
76 |
TST 7606: starting 2nd pass of memory test |
77 |
TST 7608: starting 3rd pass of memory test |
78 |
INI 70F0: memory DIMM scan complete |
79 |
INI 8805: I/O subsystem init |
80 |
INI 7300: memory configuration starting |
81 |
INI 7500: memory reset |
82 |
TST 7301: check for memory configuration change since last boot |
83 |
INI 7303: memory unchanged--use saved configuration from NVM |
84 |
INI 7304: interleave memory DIMMs |
85 |
INI 7307: generate memory interleave |
86 |
TST 7600: destructive memory test |
87 |
WRN 7601: initialize memory only (don't test) |
88 |
TST 760A: starting memory initialization |
89 |
TST 760B: memory initialization 25% complete |
90 |
TST 760B: memory initialization 50% complete |
91 |
TST 760B: memory initialization 75% complete |
92 |
TST 760B: memory initialization 100% complete |
93 |
INI 730F: memory configuration complete |
94 |
INI 8800: PCI BusWalk starting |
95 |
INI 8801: Walking Rope 0 |
96 |
INI 8811: Walking Rope 1 |
97 |
INI 8821: Walking Rope 2 |
98 |
INI 8841: Walking Rope 4 |
99 |
INI 8861: Walking Rope 6 |
100 |
INI 8802: PCI BusWalk complete |
101 |
INI 8803: PCI alloc complete |
102 |
INI 8804: PCI config complete |
103 |
WRN 4001: CPU0 late selftests skipped |
104 |
INI 103C: CPU0 initialize |
105 |
TST 400E: CPU0 exiting late selftests |
106 |
WRN 4101: CPU1 late selftests skipped |
107 |
INI 113C: CPU1 initialize |
108 |
TST 410E: CPU1 exiting late selftests |
109 |
INI CC41: CPU1 memory rendezvous |
110 |
TST 301B: check model string |
111 |
TST 301C: check/update software ID |
112 |
TST C687: try to initialize graphics in slot 7 |
113 |
INI C687: initialized graphics in slot 7 |
114 |
INI 9151: initialize SERIAL_1 |
115 |
|
116 |
|
117 |
INI 9C51: console is SERIAL_1 |
118 |
|
119 |
Firmware Version 5.0 |
120 |
|
121 |
|
122 |
Duplex Console IO Dependent Code (IODC) revision 1 |
123 |
|
124 |
------------------------------------------------------------------------------ |
125 |
|
126 |
(c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved |
127 |
|
128 |
------------------------------------------------------------------------------ |
129 |
|
130 |
|
131 |
Processor Speed State Coprocessor State I/D |
132 |
Cache |
133 |
|
134 |
--------- -------- --------------------- ----------------- |
135 |
------------- |
136 |
|
137 |
0 552 MHz Active Functional 512 |
138 |
kB/1 MB |
139 |
1 552 MHz Idle Functional 512 |
140 |
kB/1 MB |
141 |
|
142 |
Central Bus Speed: 120 MHz |
143 |
|
144 |
Available memory: 1073741824 bytes |
145 |
Good memory required: 87908352 bytes |
146 |
|
147 |
Primary boot path: FWSCSI.6.0 |
148 |
Alternate boot path: SCSI.3.0 |
149 |
Console path: SERIAL_1.9600.8.none |
150 |
Keyboard path: USB |
151 |
|
152 |
|
153 |
CPU 0 |
154 |
NOTICE : Processor self-tests have been disabled because FASTBOOT is |
155 |
enabled. To enable self-tests, disable FASTBOOT with the |
156 |
FASTBOOT |
157 |
command in the CONFIGURATION menu and reboot the system. |
158 |
NOTICE : Memory has been initialized but not tested because FASTBOOT is |
159 |
enabled. To test memory, disable FASTBOOT with the FASTBOOT |
160 |
command in the CONFIGURATION menu and reboot the system. |
161 |
|
162 |
|
163 |
CPU 1 |
164 |
NOTICE : Processor self-tests have been disabled because FASTBOOT is |
165 |
enabled. To enable self-tests, disable FASTBOOT with the |
166 |
FASTBOOT |
167 |
command in the CONFIGURATION menu and reboot the system. |
168 |
|
169 |
|
170 |
----- Main Menu |
171 |
------------------------------------------------------------- |
172 |
|
173 |
Command Description |
174 |
------- ----------- |
175 |
BOot [PRI|ALT|<path>] Boot from specified path |
176 |
PAth [PRI|ALT|CON|KEY [<path>]] Display or modify a path |
177 |
SEArch [DIsplay|[[IPL] [<path>]]] Search for boot devices |
178 |
|
179 |
COnfiguration [<command>] Access Configuration menu/commands |
180 |
INformation [<command>] Access Information menu/commands |
181 |
SERvice [<command>] Access Service menu/commands |
182 |
|
183 |
DIsplay Redisplay the current menu |
184 |
HElp [<menu>|<command>] Display help for menu or command |
185 |
RESET Restart the system |
186 |
----- |
187 |
Main Menu: Enter command > sea |
188 |
|
189 |
|
190 |
Searching for potential boot device(s)... |
191 |
|
192 |
This may take several minutes. |
193 |
|
194 |
|
195 |
To discontinue search, press any key (termination may not be immediate). |
196 |
|
197 |
|
198 |
|
199 |
Path Number Device Path Device Type |
200 |
|
201 |
----------- ----------------- ----------- |
202 |
|
203 |
P0 SCSI.3.0 TOSHIBA CD-ROM XM-5401TA |
204 |
P1 SCSI.2.0 HP C1537A |
205 |
P2 FWSCSI.6.0 FUJITSU MAJ3182MC |
206 |
|
207 |
|
208 |
Main Menu: Enter command > bo p0 |
209 |
|
210 |
Interact with IPL (Y, N, Q)?> y |
211 |
|
212 |
INI C740: initialize other path |
213 |
|
214 |
|
215 |
Booting... |
216 |
|
217 |
Boot IO Dependent Code (IODC) revision 0 |
218 |
INI C780: load IPL other path |
219 |
INI CC41: CPU1 memory rendezvous |
220 |
INI C30C: monarch slave check |
221 |
INI 10CA: CPU0 initialize system bus arbitration |
222 |
|
223 |
|
224 |
|
225 |
|
226 |
HARD Booted. |
227 |
|
228 |
INI C7FF: launch IPL other |
229 |
palo ipl 1.14 root@duet Sat Apr 8 16:08:16 EDT 2006 |
230 |
|
231 |
|
232 |
Boot image contains: |
233 |
|
234 |
0/vmlinux32 4179284 bytes @ 0xc60000 |
235 |
|
236 |
0/vmlinux64 5784983 bytes @ 0x6db800 |
237 |
|
238 |
0/ramdisk 4501015 bytes @ 0x287800 |
239 |
|
240 |
|
241 |
Information: No console specified on kernel command line. This is normal. |
242 |
|
243 |
PALO will choose the console currently used by firmware (serial).Current |
244 |
command line: |
245 |
|
246 |
'0/vmlinux root=/dev/ram initrd=0/ramdisk ramdisk_size=12432' |
247 |
console=ttyS0 TERM=vt102 |
248 |
|
249 |
0: '0/vmlinux |
250 |
|
251 |
1: root=/dev/ram |
252 |
|
253 |
2: initrd=0/ramdisk |
254 |
|
255 |
3: ramdisk_size=12432' |
256 |
|
257 |
4: console=ttyS0 |
258 |
|
259 |
5: TERM=vt102 |
260 |
|
261 |
|
262 |
<#> edit the numbered field |
263 |
|
264 |
'b' boot with this command line |
265 |
|
266 |
'r' restore command line |
267 |
|
268 |
'l' list dir |
269 |
|
270 |
? 0 |
271 |
|
272 |
'0/vmlinux32 |
273 |
|
274 |
Current command line: |
275 |
|
276 |
'0/vmlinux32 root=/dev/ram initrd=0/ramdisk ramdisk_size=12432' |
277 |
console=ttyS0 TERM=vt102 |
278 |
|
279 |
0: '0/vmlinux32 |
280 |
|
281 |
1: root=/dev/ram |
282 |
|
283 |
2: initrd=0/ramdisk |
284 |
|
285 |
3: ramdisk_size=12432' |
286 |
|
287 |
4: console=ttyS0 |
288 |
|
289 |
5: TERM=vt102 |
290 |
|
291 |
|
292 |
<#> edit the numbered field |
293 |
|
294 |
'b' boot with this command line |
295 |
|
296 |
'r' restore command line |
297 |
|
298 |
'l' list dir |
299 |
|
300 |
? 0 b |
301 |
|
302 |
|
303 |
Command line for kernel: 'root=/dev/ram ramdisk_size=12432' |
304 |
console=ttyS0 TERM=vt102 palo_kernel=0'0/vmlinux32' |
305 |
|
306 |
Selected kernel: '0/vmlinux32 from partition 0 |
307 |
|
308 |
Selected ramdisk: /ramdisk from partition 0 |
309 |
|
310 |
ELF32 executable |
311 |
|
312 |
Entry 00100000 first 00100000 n 3 |
313 |
|
314 |
Segment 0 load 00100000 size 2384552 mediaptr 0x1000 |
315 |
|
316 |
Segment 1 load 00347000 size 499712 mediaptr 0x248000 |
317 |
|
318 |
Segment 2 load 003fc000 size 381062 mediaptr 0x2c2000 |
319 |
|
320 |
Loading ramdisk 4501015 bytes @ 3fba4000... |
321 |
|
322 |
Branching to kernel entry point 0x00100000. If this is the last |
323 |
|
324 |
message you see, you may need to switch your console. This is |
325 |
|
326 |
a common symptom -- search the FAQ and mailing list at parisc-linux.org |
327 |
|
328 |
|
329 |
Linux version 2.6.18-3-parisc (Debian 2.6.18-7) (waldi@××××××.org) (gcc |
330 |
version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 Mon Dec 4 |
331 |
09:17:59 MST 2006 |
332 |
FP[0] enabled: Rev 1 Model 16 |
333 |
The 32-bit Kernel has started... |
334 |
Initialized PDC Console for debugging. |
335 |
Determining PDC firmware type: System Map. |
336 |
model 00005d10 00000491 00000000 00000002 781d75ff 100000f0 00000008 |
337 |
000000b2 000000b2 |
338 |
vers 00000300 |
339 |
CPUID vers 17 rev 10 (0x0000022a) |
340 |
capabilities 0x3 |
341 |
model 9000/785/J5600 |
342 |
Total Memory: 1024 MB |
343 |
initrd: 4fba4000-4ffeee17 |
344 |
initrd: reserving 3fba4000-3ffeee17 (mem_max 40000000) |
345 |
LCD display at f05d0008,f05d0000 registered |
346 |
Built 1 zonelists. Total pages: 262144 |
347 |
Kernel command line: root=/dev/ram ramdisk_size=12432' console=ttyS0 |
348 |
TERM=vt102 palo_kernel=0'0/vmlinux32 |
349 |
PID hash table entries: 4096 (order: 12, 16384 bytes) |
350 |
start_kernel(): bug: interrupts were enabled early |
351 |
Console: colour dummy device 160x64 |
352 |
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) |
353 |
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) |
354 |
Memory: 1048576k available |
355 |
Security Framework v1.0.0 initialized |
356 |
SELinux: Disabled at boot. |
357 |
Capability LSM initialized |
358 |
Mount-cache hash table entries: 512 |
359 |
checking if image is initramfs... it is |
360 |
Freeing initrd memory: 4395k freed |
361 |
NET: Registered protocol family 16 |
362 |
EISA bus registered |
363 |
Searching for devices... |
364 |
Found devices: |
365 |
1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } |
366 |
2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } |
367 |
3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } |
368 |
4. Elroy PCI Bridge at 0xfed34000 [10/2] { 13, 0x0, 0x782, 0x0000a } |
369 |
5. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } |
370 |
6. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } |
371 |
7. Forte W+ 2w at 0xfffa0000 [32] { 0, 0x0, 0x5d1, 0x00004 } |
372 |
8. Forte W+ 2w at 0xfffa2000 [34] { 0, 0x0, 0x5d1, 0x00004 } |
373 |
9. Memory at 0xfed10200 [49] { 1, 0x0, 0x09e, 0x00009 } |
374 |
Enabling regular chassis codes support v0.05 |
375 |
CONFIG_SMP=n ignoring additional CPUs |
376 |
CPU: probe of 34 failed with error 1 |
377 |
CPU(s): 1 x PA8600 (PCX-W+) at 552.000000 MHz |
378 |
Setting cache flush threshold to 1ec0 (1 CPUs online) |
379 |
SBA found Astro 2.1 at 0xfed00000 |
380 |
Elroy version TR4.0 (0x5) found at 0xfed30000 |
381 |
PCI: Enabled native mode for NS87415 (pif=0x8f) |
382 |
iosapic: 0xfed30800 : no IRT entry for slot 12, pin 1 |
383 |
iosapic: no IRTE for 0000:00:0c.0 (IRQ not connected?) |
384 |
iosapic: 0xfed30800 : no IRT entry for slot 13, pin 1 |
385 |
iosapic: no IRTE for 0000:00:0d.0 (IRQ not connected?) |
386 |
iosapic: 0xfed30800 : no IRT entry for slot 14, pin 4 |
387 |
iosapic: no IRTE for 0000:00:0e.2 (IRQ not connected?) |
388 |
iosapic: 0xfed30800 : no IRT entry for slot 15, pin 1 |
389 |
iosapic: no IRTE for 0000:00:0f.0 (IRQ not connected?) |
390 |
iosapic: 0xfed30800 : no IRT entry for slot 15, pin 1 |
391 |
iosapic: no IRTE for 0000:00:0f.1 (IRQ not connected?) |
392 |
Elroy version TR4.0 (0x5) found at 0xfed32000 |
393 |
Elroy version TR4.0 (0x5) found at 0xfed34000 |
394 |
Elroy version TR4.0 (0x5) found at 0xfed38000 |
395 |
Elroy version TR4.0 (0x5) found at 0xfed3c000 |
396 |
NET: Registered protocol family 2 |
397 |
IP route cache hash table entries: 32768 (order: 5, 131072 bytes) |
398 |
TCP established hash table entries: 131072 (order: 7, 524288 bytes) |
399 |
TCP bind hash table entries: 65536 (order: 6, 262144 bytes) |
400 |
TCP: Hash tables configured (established 131072 bind 65536) |
401 |
TCP reno registered |
402 |
Enabling PDC chassis warnings support v0.05 |
403 |
unwind_init: start = 0x10348cc0, end = 0x1036d620, entries = 9366 |
404 |
audit: initializing netlink socket (disabled) |
405 |
audit(1169660597.080:1): initialized |
406 |
VFS: Disk quotas dquot_6.5.1 |
407 |
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) |
408 |
Initializing Cryptographic API |
409 |
io scheduler noop registered |
410 |
io scheduler anticipatory registered |
411 |
io scheduler deadline registered |
412 |
io scheduler cfq registered (default) |
413 |
SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 1) |
414 |
SuperIO: Serial port 1 at 0x3f8 |
415 |
SuperIO: Serial port 2 at 0x2f8 |
416 |
SuperIO: Parallel port at 0x378 |
417 |
SuperIO: Floppy controller at 0x3f0 |
418 |
SuperIO: ACPI at 0x7e0 |
419 |
SuperIO: USB regulator enabled |
420 |
PDC Stable Storage facility v0.30 |
421 |
Soft power switch enabled, polling @ 0xf0400804. |
422 |
STI GSC/PCI core graphics driver Version 0.9a |
423 |
STI PCI graphic ROM found at f7000000 (128 kB), fb at fb000000 (16 MB) |
424 |
id 35acda16-9a02587, conforms to spec rev. 8.0c |
425 |
graphics card name: HPA4982A |
426 |
sticon: Initializing STI text console. |
427 |
Console: switching to colour STI console 160x64 |
428 |
stifb: 'HPA4982A' (id: 0x35acda16) not supported. |
429 |
Generic RTC Driver v1.07 |
430 |
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled |
431 |
serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A |
432 |
serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A |
433 |
RAMDISK driver initialized: 16 RAM disks of 12432K size 1024 blocksize |
434 |
mice: PS/2 mouse device common for all mice |
435 |
TCP bic registered |
436 |
NET: Registered protocol family 1 |
437 |
NET: Registered protocol family 17 |
438 |
Freeing unused kernel memory: 328k freed |
439 |
SCSI subsystem initialized |
440 |
sym0: <875> rev 0x4 at pci 0000:00:01.0 irq 65 |
441 |
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002) |
442 |
sym0: PA-RISC Firmware, ID 7, Fast-20, SE, parity checking |
443 |
sym0: SCSI BUS has been reset. |
444 |
scsi0 : sym-2.2.3 |
445 |
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 |
446 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
447 |
usbcore: registered new driver usbfs |
448 |
usbcore: registered new driver hub |
449 |
sym1: <896> rev 0x4 at pci 0000:00:0f.0 irq 1 |
450 |
sym1: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking |
451 |
IRQ handler type mismatch for IRQ 1 |
452 |
Backtrace: |
453 |
[<1014a834>] setup_irq+0x204/0x228 |
454 |
[<1014a904>] request_irq+0xac/0xe8 |
455 |
[<000a7fa8>] sym2_probe+0x624/0x830 [sym53c8xx] |
456 |
[<1022d2e8>] pci_device_probe+0x54/0x94 |
457 |
[<1026d8cc>] driver_probe_device+0x58/0xdc |
458 |
[<1026da98>] __driver_attach+0x84/0xf0 |
459 |
[<1026d1e8>] bus_for_each_dev+0x58/0x9c |
460 |
[<1026cd74>] bus_add_driver+0x78/0x148 |
461 |
[<1022d4e0>] __pci_register_driver+0x44/0x78 |
462 |
[<00031124>] sym2_init+0xfc/0x124 [sym53c8xx] |
463 |
|
464 |
sym1: request irq 1 failure |
465 |
sym1: giving up ... |
466 |
Trying to free already-free IRQ 1 |
467 |
sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 1 |
468 |
sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking |
469 |
IRQ handler type mismatch for IRQ 1 |
470 |
Backtrace: |
471 |
[<1014a834>] setup_irq+0x204/0x228 |
472 |
[<1014a904>] request_irq+0xac/0xe8 |
473 |
[<000a7fa8>] sym2_probe+0x624/0x830 [sym53c8xx] |
474 |
[<1022d2e8>] pci_device_probe+0x54/0x94 |
475 |
[<1026d8cc>] driver_probe_device+0x58/0xdc |
476 |
[<1026da98>] __driver_attach+0x84/0xf0 |
477 |
[<1026d1e8>] bus_for_each_dev+0x58/0x9c |
478 |
[<1026cd74>] bus_add_driver+0x78/0x148 |
479 |
[<1022d4e0>] __pci_register_driver+0x44/0x78 |
480 |
[<00031124>] sym2_init+0xfc/0x124 [sym53c8xx] |
481 |
|
482 |
sym1: request irq 1 failure |
483 |
sym1: giving up ... |
484 |
Trying to free already-free IRQ 1 |
485 |
sym1: <875> rev 0x4 at pci 0000:02:02.0 irq 66 |
486 |
tulip0: no phy info, aborting mtable build |
487 |
tulip0: MII transceiver #1 config 1200 status 7809 advertising 01e1. |
488 |
eth0: Digital DS21142/43 Tulip rev 65 at Port 0x1000, 00:10:83:FF:1E:7E, |
489 |
IRQ 2. |
490 |
NS87415: IDE controller at PCI slot 0000:00:0e.0 |
491 |
NS87415: chipset revision 3 |
492 |
NS87415: 100% native mode on irq 7 |
493 |
ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA |
494 |
ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA |
495 |
sym1: PA-RISC Firmware, ID 7, Fast-20, SE, parity checking |
496 |
sym1: SCSI BUS has been reset. |
497 |
scsi3 : sym-2.2.3 |
498 |
ohci_hcd 0000:00:0e.2: OHCI Host Controller |
499 |
ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 |
500 |
IRQ handler type mismatch for IRQ 1 |
501 |
Backtrace: |
502 |
[<1014a834>] setup_irq+0x204/0x228 |
503 |
[<1014a904>] request_irq+0xac/0xe8 |
504 |
[<001086e4>] usb_add_hcd+0x324/0x654 [usbcore] |
505 |
[<00111404>] usb_hcd_pci_probe+0x21c/0x2c0 [usbcore] |
506 |
[<1022d2e8>] pci_device_probe+0x54/0x94 |
507 |
[<1026d8cc>] driver_probe_device+0x58/0xdc |
508 |
[<1026da98>] __driver_attach+0x84/0xf0 |
509 |
[<1026d1e8>] bus_for_each_dev+0x58/0x9c |
510 |
[<1026cd74>] bus_add_driver+0x78/0x148 |
511 |
[<1022d4e0>] __pci_register_driver+0x44/0x78 |
512 |
[<10143d1c>] sys_init_module+0x123c/0x13ec |
513 |
[<1010c134>] syscall_exit+0x0/0x14 |
514 |
|
515 |
ohci_hcd 0000:00:0e.2: request interrupt 1 failed |
516 |
ohci_hcd 0000:00:0e.2: USB bus 1 deregistered |
517 |
ohci_hcd 0000:00:0e.2: init 0000:00:0e.2 fail, -16 |
518 |
ohci_hcd: probe of 0000:00:0e.2 failed with error -16 |
519 |
|
520 |
-- |
521 |
gentoo-hppa@g.o mailing list |