1 |
Greetings, |
2 |
|
3 |
I recently acquired a HP9000 819 K200 server, and I am trying to get |
4 |
gentoo loaded on it. The system does boot HP-UX off the original drives |
5 |
so I know the system is in working order. When I try to boot gentoo, |
6 |
the system seems to go into an infinite loop after it detects the |
7 |
second MUX card. I have attached the log file of the boot process. |
8 |
|
9 |
I did try to boot debian too, and that actually panics the |
10 |
system. If it would be helpful, I can capture that boot process as well. |
11 |
|
12 |
|
13 |
Firmware Version 2.0 |
14 |
|
15 |
Duplex Console IO Dependent Code (IONIC) revision 4 |
16 |
|
17 |
------------------------------------------------------------------------------ |
18 |
(c) Copyright 1990-1994, Hewlett-Packard Company, All rights reserved |
19 |
------------------------------------------------------------------------------ |
20 |
|
21 |
Processor Speed State CoProcessor State Cache Size |
22 |
--------- -------- --------------------- ----------------- ---------- |
23 |
|
24 |
0 100 MHz Active Functional 256 KB |
25 |
|
26 |
Central Bus Speed (in MHz) : 100 |
27 |
Available Memory (bytes) : 268435456 |
28 |
Good Memory Required (bytes): 25538560 |
29 |
|
30 |
|
31 |
Primary boot path: 10/0.9 (dec) |
32 |
Alternate boot path: 10/12/5.2 (dec) |
33 |
Console path: 10/4/0.0 (dec) |
34 |
Keyboard path: 10/12/7.0 (dec) |
35 |
|
36 |
|
37 |
Processor is booting from first available device. |
38 |
|
39 |
To discontinue, press any key within 10 seconds. |
40 |
|
41 |
Boot terminated. |
42 |
|
43 |
|
44 |
------- Main Menu ------------------------------------------------------------- |
45 |
|
46 |
Command Description |
47 |
------- ----------- |
48 |
|
49 |
BOot [PRI|ALT|<path>] Boot from specified path |
50 |
PAth [PRI|ALT] [<path>] Display or modify a path |
51 |
SEArch [DIsplay|IPL] [<path>] Search for boot devices |
52 |
|
53 |
COnfiguration menu Displays or sets boot values |
54 |
INformation menu Displays hardware information |
55 |
SERvice menu Displays service commands |
56 |
|
57 |
DIsplay Redisplay the current menu |
58 |
HElp [<menu>|<command>] Display help for menu or command |
59 |
RESET Restart the system |
60 |
------- |
61 |
Main Menu: Enter command or menu > bo alt |
62 |
Interact with IPL (Y or N)?> y |
63 |
|
64 |
Booting... |
65 |
Boot IO Dependent Code (IODC) revision 0 |
66 |
|
67 |
|
68 |
HARD Booted. |
69 |
palo ipl 1.5 root@hope Sat Apr 23 18:06:47 CEST 2005 |
70 |
|
71 |
Boot image contains: |
72 |
0/vmlinux32 5894177 bytes @ 0x3d6b000 |
73 |
0/vmlinux64 7167445 bytes @ 0x430a800 |
74 |
0/ramdisk 963641 bytes @ 0x3c7d800 |
75 |
|
76 |
Information: No console specified on kernel command line. This is normal. |
77 |
PALO will choose the console currently used by firmware (serial).Current command line: |
78 |
0/vmlinux initrd=initrd TERM=linux root=/dev/ram0 init=/linuxrc cdroot looptype=squashfs loop=/image.squashfs hda=scsi hdb=scsi console=ttyB0 |
79 |
0: 0/vmlinux |
80 |
1: initrd=initrd |
81 |
2: TERM=linux |
82 |
3: root=/dev/ram0 |
83 |
4: init=/linuxrc |
84 |
5: cdroot |
85 |
6: looptype=squashfs |
86 |
7: loop=/image.squashfs |
87 |
8: hda=scsi |
88 |
9: hdb=scsi |
89 |
10: console=ttyB0 |
90 |
|
91 |
<#> edit the numbered field |
92 |
'b' boot with this command line |
93 |
'r' restore command line |
94 |
'l' list dir |
95 |
? b |
96 |
|
97 |
Command line for kernel: ' TERM=linux root=/dev/ram0 init=/linuxrc cdroot looptype=squashfs loop=/image.squashfs hda=scsi hdb=scsi console=ttyB0 palo_kernel=0/vmlinux' |
98 |
Selected kernel: /vmlinux from partition 0 |
99 |
Selected ramdisk: initrd from partition 0 |
100 |
Warning: kernel name doesn't end with 32 or 64 -- Guessing... Choosing 32-bit kernelELF32 executable |
101 |
Entry 00100000 first 00100000 n 4 |
102 |
Segment 0 load 00100000 size 3827224 mediaptr 0x1000 |
103 |
Segment 1 load 004a7000 size 685496 mediaptr 0x3a8000 |
104 |
Segment 2 load 00550000 size 422021 mediaptr 0x450000 |
105 |
Segment 3 load 00000000 size 0 mediaptr 0x0 |
106 |
Loading ramdisk 963641 bytes @ 0ff04000... |
107 |
Branching to kernel entry point 0x00100000. If this is the last |
108 |
message you see, you may need to switch your console. This is |
109 |
a common symptom -- search the FAQ and mailing list at parisc-linux.org |
110 |
|
111 |
Linux version 2.6.15.1-pa4-livecd32 (root@hake) (gcc version 3.3.6 (Gentoo 3.3.6, pie-8.7.8)) #1 Sun Feb 19 07:39:43 UTC 2006 |
112 |
FP[0] enabled: Rev 1 Model 11 |
113 |
The 32-bit Kernel has started... |
114 |
Initialized PDC Console for debugging. |
115 |
Determining PDC firmware type: System Map. |
116 |
model 000058b0 00000491 00000000 00000002 00382c3d 100000f1 00000004 0000008a 0000008a |
117 |
vers 0000000d |
118 |
CPUID vers 11 rev 13 (0x0000016d) |
119 |
model 9000/819/K200 |
120 |
Total Memory: 256 MB |
121 |
initrd: 1ff04000-1ffef439 |
122 |
initrd: reserving 0ff04000-0ffef439 (mem_max 10000000) |
123 |
drivers/parisc/led.c: KittyHawk-Machine (hversion 0x58b) found, LED detection skipped. |
124 |
LCD display at f0190000,f0190001 registered |
125 |
Built 1 zonelists |
126 |
Kernel command line: TERM=linux root=/dev/ram0 init=/linuxrc cdroot looptype=squashfs loop=/image.squashfs hda=scsi hdb=scsi console=ttyB0 palo_kernel=0/vmlinux |
127 |
ide_setup: hda=scsi |
128 |
ide_setup: hdb=scsi |
129 |
PID hash table entries: 2048 (order: 11, 32768 bytes) |
130 |
Console: colour dummy device 160x64 |
131 |
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) |
132 |
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) |
133 |
Memory: 262144k available |
134 |
Mount-cache hash table entries: 512 |
135 |
checking if image is initramfs... it is |
136 |
NET: Registered protocol family 16 |
137 |
EISA bus registered |
138 |
Searching for devices... |
139 |
Found devices: |
140 |
1. U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0x7, 0x580, 0x0000b } |
141 |
2. KittyHawk GSY Core BA at 0xffd00000 [10/12] { 11, 0x0, 0x015, 0x00081 }, additional addresses: 0xffd0c000 0xffc00000 |
142 |
3. KittyHawk GSY Core SCSI at 0xffd06000 [10/12/5] { 10, 0x0, 0x015, 0x00082 } |
143 |
4. KittyHawk GSY Core LAN (802.3) at 0xffd07000 [10/12/6] { 10, 0x0, 0x015, 0x0008a } |
144 |
5. KittyHawk GSY Core Centronics at 0xffd02000 [10/12/0] { 10, 0x0, 0x015, 0x00074 }, additional addresses: 0xffd01000 0xffd03000 |
145 |
6. KittyHawk GSY Core PS/2 Port at 0xffd08000 [10/12/7] { 10, 0x0, 0x015, 0x00084 } |
146 |
7. KittyHawk GSY Core PS/2 Port at 0xffd08100 [10/12/8] { 10, 0x0, 0x015, 0x00084 } |
147 |
8. KittyHawk GSY Core FW-SCSI at 0xf1800000 [10/0] { 4, 0x1, 0x015, 0x00089 } |
148 |
9. Gecko BOA BC GSC+ Port at 0xf1804000 [10/4] { 7, 0x0, 0x500, 0x0000c } |
149 |
10. Eole CAP/MUX at 0xf1900000 [10/4/0] { 5, 0x0, 0x015, 0x0000d } |
150 |
11. Skunk SCSI (28655A) at 0xf1908000 [10/4/8] { 4, 0x0, 0x004, 0x00039 } |
151 |
12. Skunk Centronics (28655A) at 0xf1909000 [10/4/9] { 5, 0x0, 0x004, 0x0003a } |
152 |
13. Wizard SCSI at 0xf190c000 [10/4/12] { 4, 0x0, 0x004, 0x0003b } |
153 |
14. Solaris Modem MUX (J2094A) at 0xf1910000 [10/4/16] { 5, 0x0, 0x00c, 0x0000d } |
154 |
15. Gecko BOA BC HP-PB Port at 0xf193c000 [10/4/60] { 7, 0x0, 0x103, 0x0000c } |
155 |
16. HP HSC-PCI Cards at 0xf1808000 [10/8] { 4, 0x0, 0x004, 0x0009d } |
156 |
17. U2-IOA BC GSC+ Port at 0xf183f000 [10/63] { 7, 0x1, 0x501, 0x0000c } |
157 |
18. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0x7, 0x580, 0x0000b } |
158 |
19. U2-IOA BC GSC+ Port at 0xf103f000 [8/63] { 7, 0x1, 0x501, 0x0000c } |
159 |
20. KittyHawk DC2 100 (K200) at 0xfffa0000 [32] { 0, 0x0, 0x58b, 0x00004 } |
160 |
21. Memory at 0xfffb1000 [49] { 1, 0x0, 0x053, 0x00009 } |
161 |
CPU(s): 1 x PA7200 (PCX-T') at 100.000000 MHz |
162 |
Setting cache flush threshold to 360 (1 CPUs online) |
163 |
Found U2 at 0xfff8a000 |
164 |
Found U2 at 0xfff88000 |
165 |
Lasi version 0 at 0xffd00000 found. |
166 |
Found GeckoBoa at 0xf1804000 |
167 |
Dino version 3.x (card mode) found at 0xf1808000 |
168 |
Generic PHY: Registered new driver |
169 |
SCSI subsystem initialized |
170 |
usbcore: registered new driver usbfs |
171 |
usbcore: registered new driver hub |
172 |
unwind_init: start = 0x104a90b0, end = 0x104df6b0, entries = 13920 |
173 |
Squashfs 2.1 (released 2004/12/10) (C) 2002-2004 Phillip Lougher |
174 |
Installing knfsd (copyright (C) 1996 okir@×××××××××.de). |
175 |
SGI XFS with ACLs, security attributes, realtime, no debug enabled |
176 |
SGI XFS Quota Management subsystem |
177 |
Initializing Cryptographic API |
178 |
io scheduler noop registered |
179 |
io scheduler anticipatory registered |
180 |
io scheduler deadline registered |
181 |
io scheduler cfq registered |
182 |
PDC Stable Storage facility v0.22 |
183 |
Soft power switch support not available. |
184 |
STI GSC/PCI core graphics driver Version 0.9a |
185 |
Generic RTC Driver v1.07 |
186 |
serio: GSC PS/2 keyboard port at 0xffd08000 irq 19 @ 10:12:7 |
187 |
serio: GSC PS/2 mouse port at 0xffd08100 irq 19 @ 10:12:8 |
188 |
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled |
189 |
Serial mux driver (8 ports) Revision: 0.3 |
190 |
ttyB0 at MMIO 0xf1900800 (polled) is a Mux |
191 |
ttyB1 at MMIO 0xf1900880 (polled) is a Mux |
192 |
ttyB2 at MMIO 0xf1900900 (polled) is a Mux |
193 |
ttyB3 at MMIO 0xf1900980 (polled) is a Mux |
194 |
ttyB4 at MMIO 0xf1900a00 (polled) is a Mux |
195 |
ttyB5 at MMIO 0xf1900a80 (polled) is a Mux |
196 |
ttyB6 at MMIO 0xf1900b00 (polled) is a Mux |
197 |
ttyB7 at MMIO 0xf1900b80 (polled) is a Mux |
198 |
Serial mux driver (16 ports) Revision: 0.3 |
199 |
ttyB8 at MMIO 0xf1910800 (polled) is a Mux |
200 |
ttyB9 at MMIO 0xf1910880 (polled) is a Mux |
201 |
ttyB10 at MMIO 0xf1910900 (polled) is a Mux |
202 |
ttyB11 at MMIO 0xf1910980 (polled) is a Mux |
203 |
ttyB12 at MMIO 0xf1910a00 (polled) is a Mux |
204 |
ttyB13 at MMIO 0xf1910a80 (polled) is a Mux |
205 |
ttyB14 at MMIO 0xf1910b00 (polled) is a Mux |
206 |
ttyB15 at MMIO 0xf1910b80 (polled) is a Mux |
207 |
ttyB16 at MMIO 0xf1910c00 (polled) is a Mux |
208 |
ttyB17 at MMIO 0xf1910c80 (polled) is a Mux |
209 |
ttyB18 at MMIO 0xf1910d00 (polled) is a Mux |
210 |
ttyB19 at MMIO 0xf1910d80 (polled) is a Mux |
211 |
ttyB20 at MMIO 0xf1910e00 (polled) is a Mux |
212 |
ttyB21 at MMIO 0xf1910e80 (polled) is a Mux |
213 |
ttyB22 at MMIO 0xf1910f00 (polled) is a Mux |
214 |
ttyB23 at MMIO 0xf1910f80 (polled) is a Mux |
215 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
216 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
217 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
218 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
219 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
220 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
221 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
222 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
223 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
224 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
225 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
226 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
227 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
228 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
229 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
230 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
231 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
232 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
233 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
234 |
<keeps scrolling for ever, or at least 15 minutes before I power down> |
235 |
|
236 |
Thank you in advance, |
237 |
Brett |
238 |
-- |
239 |
gentoo-hppa@g.o mailing list |