1 |
Ok, there is an old J5600 at work I want to install Gentoo, but I am at |
2 |
a loss. The IDE CDROM caused a panic so I found an old SCSI drive and |
3 |
gave it another shot. Hooked to a monitor and USB mouse and keyboard |
4 |
the CD will load until the first install screen and the keyboard will |
5 |
not work. So I hooked it up to a WinXP laptop via HyperTerm and it loads |
6 |
up to here: |
7 |
|
8 |
Freeing unused kernel memory: 368k freed |
9 |
|
10 |
Nothing after this... |
11 |
|
12 |
Here is the start to stop: |
13 |
|
14 |
Command line for kernel: ' TERM=linux root=/dev/ram0 init=/bin/sh cdroot |
15 |
looptype=squashfs loop=/image.squashfs hda=scsi hdb=scsi console=ttyS0 |
16 |
palo_kernel=0/vmlinux32' |
17 |
Selected kernel: /vmlinux32 from partition 0 |
18 |
Selected ramdisk: initrd from partition 0 |
19 |
ELF32 executable |
20 |
Entry 00100000 first 00100000 n 4 |
21 |
Segment 0 load 00100000 size 3827224 mediaptr 0x1000 |
22 |
Segment 1 load 004a7000 size 685496 mediaptr 0x3a8000 |
23 |
Segment 2 load 00550000 size 422021 mediaptr 0x450000 |
24 |
Segment 3 load 00000000 size 0 mediaptr 0x0 |
25 |
Loading ramdisk 963641 bytes @ 3ff04000... |
26 |
Branching to kernel entry point 0x00100000. If this is the last |
27 |
message you see, you may need to switch your console. This is |
28 |
a common symptom -- search the FAQ and mailing list at parisc-linux.org |
29 |
|
30 |
Linux version 2.6.15.1-pa4-livecd32 (root@hake) (gcc version 3.3.6 |
31 |
(Gentoo 3.3.6, pie-8.7.8)) #1 Sun Feb 19 07:39:43 UTC 2006 |
32 |
FP[0] enabled: Rev 1 Model 16 |
33 |
The 32-bit Kernel has started... |
34 |
Initialized PDC Console for debugging. |
35 |
Determining PDC firmware type: System Map. |
36 |
model 00005d10 00000491 00000000 00000002 781d75ff 100000f0 00000008 |
37 |
000000b2 000000b2 |
38 |
vers 00000300 |
39 |
CPUID vers 17 rev 10 (0x0000022a) |
40 |
capabilities 0x3 |
41 |
model 9000/785/J5600 |
42 |
Total Memory: 1024 MB |
43 |
initrd: 4ff04000-4ffef439 |
44 |
initrd: reserving 3ff04000-3ffef439 (mem_max 40000000) |
45 |
LCD display at f05d0008,f05d0000 registered |
46 |
Built 1 zonelists |
47 |
Kernel command line: TERM=linux root=/dev/ram0 init=/bin/sh cdroot |
48 |
looptype=squashfs loop=/image.squashfs hda=scsi hdb=scsi console=ttyS0 |
49 |
palo_kernel=0/vmlinux32 |
50 |
ide_setup: hda=scsi |
51 |
ide_setup: hdb=scsi |
52 |
PID hash table entries: 4096 (order: 12, 65536 bytes) |
53 |
Console: colour dummy device 160x64 |
54 |
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) |
55 |
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) |
56 |
Memory: 1048576k available |
57 |
Mount-cache hash table entries: 512 |
58 |
checking if image is initramfs... it is |
59 |
NET: Registered protocol family 16 |
60 |
EISA bus registered |
61 |
Searching for devices... |
62 |
Found devices: |
63 |
1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } |
64 |
2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } |
65 |
3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } |
66 |
4. Elroy PCI Bridge at 0xfed34000 [10/2] { 13, 0x0, 0x782, 0x0000a } |
67 |
5. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } |
68 |
6. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } |
69 |
7. Forte W+ 2w at 0xfffa0000 [32] { 0, 0x0, 0x5d1, 0x00004 } |
70 |
8. Forte W+ 2w at 0xfffa2000 [34] { 0, 0x0, 0x5d1, 0x00004 } |
71 |
9. Memory at 0xfed10200 [49] { 1, 0x0, 0x09e, 0x00009 } |
72 |
CONFIG_SMP=n ignoring additional CPUs |
73 |
CPU: probe of 34 failed with error 1 |
74 |
CPU(s): 1 x PA8600 (PCX-W+) at 552.000000 MHz |
75 |
Setting cache flush threshold to 6c0 (1 CPUs online) |
76 |
SBA found Astro 2.1 at 0xfed00000 |
77 |
LBA version TR4.0 (0x5) found at 0xfed30000 |
78 |
PCI: Enabled native mode for NS87415 (pif=0x8f) |
79 |
iosapic: 0xfed30800 : no IRT entry for slot 12, pin 1 |
80 |
iosapic: no IRTE for 0000:00:0c.0 (IRQ not connected?) |
81 |
iosapic: 0xfed30800 : no IRT entry for slot 13, pin 1 |
82 |
iosapic: no IRTE for 0000:00:0d.0 (IRQ not connected?) |
83 |
iosapic: 0xfed30800 : no IRT entry for slot 14, pin 4 |
84 |
iosapic: no IRTE for 0000:00:0e.2 (IRQ not connected?) |
85 |
iosapic: 0xfed30800 : no IRT entry for slot 15, pin 1 |
86 |
iosapic: no IRTE for 0000:00:0f.0 (IRQ not connected?) |
87 |
iosapic: 0xfed30800 : no IRT entry for slot 15, pin 1 |
88 |
iosapic: no IRTE for 0000:00:0f.1 (IRQ not connected?) |
89 |
LBA version TR4.0 (0x5) found at 0xfed32000 |
90 |
LBA version TR4.0 (0x5) found at 0xfed34000 |
91 |
LBA version TR4.0 (0x5) found at 0xfed38000 |
92 |
LBA version TR4.0 (0x5) found at 0xfed3c000 |
93 |
Generic PHY: Registered new driver |
94 |
SCSI subsystem initialized |
95 |
usbcore: registered new driver usbfs |
96 |
usbcore: registered new driver hub |
97 |
unwind_init: start = 0x104a90b0, end = 0x104df6b0, entries = 13920 |
98 |
Squashfs 2.1 (released 2004/12/10) (C) 2002-2004 Phillip Lougher |
99 |
Installing knfsd (copyright (C) 1996 okir@×××××××××.de). |
100 |
SGI XFS with ACLs, security attributes, realtime, no debug enabled |
101 |
SGI XFS Quota Management subsystem |
102 |
Initializing Cryptographic API |
103 |
io scheduler noop registered |
104 |
io scheduler anticipatory registered |
105 |
io scheduler deadline registered |
106 |
io scheduler cfq registered |
107 |
SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 1) |
108 |
SuperIO: Serial port 1 at 0x3f8 |
109 |
SuperIO: Serial port 2 at 0x2f8 |
110 |
SuperIO: Parallel port at 0x378 |
111 |
SuperIO: Floppy controller at 0x3f0 |
112 |
SuperIO: ACPI at 0x7e0 |
113 |
SuperIO: USB regulator enabled |
114 |
PDC Stable Storage facility v0.22 |
115 |
Soft power switch enabled, polling @ 0xf0400804. |
116 |
STI GSC/PCI core graphics driver Version 0.9a |
117 |
STI PCI graphic ROM found at f7000000 (128 kB), fb at fb000000 (16 MB) |
118 |
id 35acda16-9a02587, conforms to spec rev. 8.0c |
119 |
graphics card name: HPA4982A |
120 |
sticon: Initializing STI text console. |
121 |
Console: switching to colour STI console 160x64 |
122 |
stifb: 'HPA4982A' (id: 0x35acda16) not supported. |
123 |
Generic RTC Driver v1.07 |
124 |
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled |
125 |
serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A |
126 |
serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A |
127 |
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
128 |
loop: loaded (max 8 devices) |
129 |
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 |
130 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
131 |
NS87415: IDE controller at PCI slot 0000:00:0e.0 |
132 |
NS87415: chipset revision 3 |
133 |
NS87415: 100% native mode on irq 7 |
134 |
ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA |
135 |
ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA |
136 |
sym0: <875> rev 0x4 at pci 0000:00:01.0 irq 65 |
137 |
sym0: PA-RISC Firmware, ID 7, Fast-20, SE, parity checking |
138 |
sym0: SCSI BUS has been reset. |
139 |
scsi0 : sym-2.2.2 |
140 |
sym1: <896> rev 0x4 at pci 0000:00:0f.0 irq 1 |
141 |
sym1: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking |
142 |
sym1: request irq 1 failure |
143 |
sym1: giving up ... |
144 |
sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 1 |
145 |
sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking |
146 |
sym1: request irq 1 failure |
147 |
sym1: giving up ... |
148 |
sym1: <875> rev 0x4 at pci 0000:02:02.0 irq 66 |
149 |
sym1: PA-RISC Firmware, ID 7, Fast-20, SE, parity checking |
150 |
sym1: SCSI BUS has been reset. |
151 |
scsi3 : sym-2.2.2 |
152 |
st: Version 20050830, fixed bufsize 32768, s/g segs 256 |
153 |
usbmon: debugfs is not available |
154 |
ohci_hcd 0000:00:0e.2: OHCI Host Controller |
155 |
ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 |
156 |
ohci_hcd 0000:00:0e.2: request interrupt 1 failed |
157 |
ohci_hcd 0000:00:0e.2: USB bus 1 deregistered |
158 |
ohci_hcd 0000:00:0e.2: init 0000:00:0e.2 fail, -16 |
159 |
ohci_hcd: probe of 0000:00:0e.2 failed with error -16 |
160 |
usbcore: registered new driver hiddev |
161 |
usbcore: registered new driver usbhid |
162 |
drivers/usb/input/hid-core.c: v2.6:USB HID core driver |
163 |
mice: PS/2 mouse device common for all mice |
164 |
NET: Registered protocol family 2 |
165 |
IP route cache hash table entries: 65536 (order: 6, 262144 bytes) |
166 |
TCP established hash table entries: 262144 (order: 8, 1048576 bytes) |
167 |
TCP bind hash table entries: 65536 (order: 6, 262144 bytes) |
168 |
TCP: Hash tables configured (established 262144 bind 65536) |
169 |
TCP reno registered |
170 |
TCP bic registered |
171 |
NET: Registered protocol family 1 |
172 |
NET: Registered protocol family 10 |
173 |
lo: Disabled Privacy Extensions |
174 |
IPv6 over IPv4 tunneling driver |
175 |
NET: Registered protocol family 17 |
176 |
Freeing unused kernel memory: 368k freed |
177 |
|
178 |
Here is some of the machine info: |
179 |
|
180 |
I/O MODULE INFORMATION |
181 |
|
182 |
|
183 |
IODC IODC |
184 |
Path Decimal Type Location HVER SVER Vers Dep |
185 |
------------ ----------- --------------------- ---------- ---- ---- ---- |
186 |
---- |
187 |
PCI1 10/0/1/0 SCSI slot 1 0070 a300 0x00 |
188 |
0x00 |
189 |
LAN 10/0/12/0 Ethernet built-in 0040 a200 0x02 |
190 |
0x00 |
191 |
AUDIO 10/0/13/0 Audio built-in |
192 |
IDE 10/0/14/0 IDE built-in 0040 a300 0x00 |
193 |
0x00 |
194 |
SUPERIO MISC 10/0/14/1 Bridge Device built-in |
195 |
SERIAL_1 10/0/14/1/1 RS232 Port built-in 0040 8c00 0x01 |
196 |
0x00 |
197 |
SERIAL_2 10/0/14/1/2 RS232 Port built-in 0040 8c00 0x01 |
198 |
0x00 |
199 |
PARALLEL 10/0/14/1/3 Parallel Port built-in |
200 |
USB 10/0/14/2 USB built-in 0040 a900 0x98 |
201 |
0x00 |
202 |
SCSI 10/0/15/0 SCSI built-in 0040 a300 0x00 |
203 |
0x00 |
204 |
FWSCSI 10/0/15/1 SCSI built-in 0040 a300 0x00 |
205 |
0x00 |
206 |
PCI2 10/2/2/0 SCSI slot 2 0070 a300 0x00 |
207 |
0x00 |
208 |
GRAPHICS(7) 10/6/7/0 HPA4982A slot 7 0070 8500 0x01 |
209 |
0x00 |
210 |
|
211 |
PROCESSOR INFORMATION |
212 |
|
213 |
|
214 |
HVERSION SVERSION CVERSION Processor |
215 |
|
216 |
Processor Speed Model Model/Op (Revision) State |
217 |
|
218 |
--------- -------- -------- -------- ---------- ------------- |
219 |
|
220 |
0 552 MHz 0x5d10 0x0491 768 Active |
221 |
1 552 MHz 0x5d10 0x0491 768 Idle |
222 |
|
223 |
Central Bus Speed: 120 MHz |
224 |
Software ID: 2015196671 (dec) |
225 |
Software ID: 0x781d75ff (hex) |
226 |
Software Capability: 0xf0 |
227 |
|
228 |
FIRMWARE INFORMATION |
229 |
|
230 |
|
231 |
Firmware Version: 5.0 |
232 |
|
233 |
4118 |
234 |
|
235 |
|
236 |
CHIP REVISIONS |
237 |
|
238 |
|
239 |
Module Revision |
240 |
------------------- -------- |
241 |
System Board 0 |
242 |
PA 8600-8600 CPU 3.0 |
243 |
PA 8600-8600 CPU 3.0 |
244 |
Mem/IO Controller 2.1 |
245 |
PCI Controller #0 4.0 |
246 |
PCI Controller #1 4.0 |
247 |
PCI Controller #2 4.0 |
248 |
PCI Controller #4 4.0 |
249 |
PCI Controller #6 4.0 |
250 |
PDC 5.0 (1 MB) |
251 |
Micro Controller 1.1 |
252 |
I/O Board 0 |
253 |
Disk Board 1 |
254 |
Power Supply 0 |
255 |
|
256 |
GRAPHICS(7) 8.12/20 35acda16.09a02587 |
257 |
|
258 |
|
259 |
|
260 |
Michael |
261 |
|
262 |
|
263 |
-- |
264 |
gentoo-hppa@g.o mailing list |