Gentoo Logo
Gentoo Spaceship




Note: Due to technical difficulties, the Archives are currently not up to date. GMANE provides an alternative service for most mailing lists.
c.f. bug 424647
List Archive: gentoo-kernel
Navigation:
Lists: gentoo-kernel: < Prev By Thread Next > < Prev By Date Next >
Headers:
To: gentoo-kernel@g.o
From: puNk!d <punkid.online@...>
Subject: Kernels (>2.6.13) dont recognize my sata disk on K8N4-E
Date: Thu, 20 Sep 2007 16:31:00 +0800
I posted this on forums, but no one give me a clue, so i ask for here, hoping someone can help me out.<br>&nbsp;&nbsp;<br>For saving your time, let me first illustrate my prob briefly. I have an ASUS K8N4-4 nForce4 mainboard, and a 160G Maxtor SATA harddisk (6V160E0). But all of the kernels (&gt;
2.6.13) couldnt recognize my harddisk, it showed the VFS: Cannot open root device &quot;sda9&quot; or unknown-block(0,0)&nbsp;&nbsp;error when booting. I tried gentoo-sources, genkernel, vanilla-kernel,mm-sources and even sabayon-sources, they all failed. However, the kernels &lt;=
2.6.13 work well. I know you might tell me to have a look at my kernel config, check twice that had i enabled the SATA device support, I really did it, you can take a look at my kernel config in this thread. <br>&nbsp;&nbsp;<br> I tried the K8N4-E keywords in this forums, i found there were many guys who use that mainboard suffering the same prob. Such as: 
<br>&nbsp; <br><ol><li><a href="http://forums.gentoo.org/viewtopic-t-522268-highlight-k8n4e.html">SATA drives not recognized on kernel &gt; 2.6.11</a></li><li><a href="http://forums.gentoo.org/viewtopic-t-525163-highlight-k8n4e.html">
Problem finding my SATA-drives</a></li><li><a href="http://forums.gentoo.org/viewtopic-t-510265-highlight-kernel+panic.html">What does &quot;VFS: Cannot open root device...&quot; mean, exactly?</a>&nbsp;&nbsp;(my former reply following a Tips &amp; Tricks thread) 
</li></ol>in the 2nd one, someone named addeman also confirmed this weird prob, and no one really gave a solution. <br>&nbsp;&nbsp;<br>Recently I had a chance to try Kubuntu 7.04 feisty LiveCD, i found it could recognize my SATA harddisk with 
kernel-2.6.20, it makes me wondering is it a prob of the kernel itself or the gentoo system. So i downloaded Fedora 7 LiveCD (kernel-2.6.21), it can also recognize my sata device! Then i decided to have a test on Fedora 7 LiveCD&#39;s kernel by a dirty way, i copyed the vmlinuz image,the modules and the 
modprobe.conf setting into my gentoo system, try to boot from Fedora&#39;s kernel, it failed with the same VFS: Cannot open root device &quot;sda9&quot; or unknown-block(0,0) error. <br>&nbsp;&nbsp;<br> Okay, now let me tell you my gentoo setting. Here&#39;s my partition list. 
<br>&nbsp; <br><div style="margin-left: 40px;"> Filesystem&nbsp;&nbsp;&nbsp;&nbsp;Type&nbsp;&nbsp;&nbsp;&nbsp; Size&nbsp;&nbsp;Used&nbsp;&nbsp;Avail Use% Mounted on <br> /dev/sda8&nbsp;&nbsp;&nbsp;&nbsp; ext2&nbsp;&nbsp;&nbsp;&nbsp;38M&nbsp;&nbsp; 8.4M&nbsp;&nbsp; 28M&nbsp;&nbsp;24% /boot <br> /dev/sda9&nbsp;&nbsp;reiserfs&nbsp;&nbsp;&nbsp;&nbsp; 18G&nbsp;&nbsp; 5.3G&nbsp;&nbsp; 13G&nbsp;&nbsp;30% / <br> /dev/sda10 reiserfs&nbsp;&nbsp;&nbsp;&nbsp;
8.1G&nbsp;&nbsp; 4.9G&nbsp;&nbsp;3.2G&nbsp;&nbsp;61% /home <br></div> 	 <br> my grub.conf <br>&nbsp; <br><div style="margin-left: 40px;"> title=Gentoo Linux 2.6.13 <br> root (hd0,7) <br> kernel /boot/vmlinuz-2.6.13-gentoo-r5 root=/dev/sda9 video=vesafb:mtrr,ywrap,1440x900-32 
<br>&nbsp;&nbsp;<br> title=Gentoo Linux 2.6.22 <br> root (hd0,7) <br> kernel /boot/vmlinuz-2.6.22-gentoo-r6 root=/dev/sda9 video=vesafb:mtrr,ywrap,1440x900-32 <br></div> 	 <br> the dmesg output (running on my gentoo system with kernel 
2.6.13) <br>&nbsp; <br><div style="margin-left: 40px;"> Console: colour VGA+ 80x25 <br> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <br> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <br> Memory: 514308k/524224k available (2893k kernel code, 9364k reserved, 1174k data, 180k init, 0k highmem) 
<br> Checking if this processor honours the WP bit even in supervisor mode... Ok. <br> Calibrating delay using timer specific routine.. 3620.94 BogoMIPS (lpj=1810472) <br> Mount-cache hash table entries: 512 <br> CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 
<br> CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 <br> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <br> CPU: L2 Cache: 128K (64 bytes/line) <br> CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000001 
<br> Intel machine check architecture supported. <br> Intel machine check reporting enabled on CPU#0. <br> mtrr: v2.0 (20020519) <br> CPU: AMD Sempron(tm) Processor 3000+ stepping 02 <br> Enabling fast FPU save and restore... done. 
<br> Enabling unmasked SIMD FPU exception support... done. <br> Checking &#39;hlt&#39; instruction... OK. <br> ACPI: setting ELCR to 0200 (from 0828) <br> NET: Registered protocol family 16 <br> ACPI: bus type pci registered 
<br> PCI: PCI BIOS revision 3.00 entry at 0xf1f20, last bus=5 <br> PCI: Using configuration type 1 <br> ACPI: Subsystem revision 20050408 <br> ACPI: Interpreter enabled <br> ACPI: Using PIC for interrupt routing <br> ACPI: PCI Root Bridge [PCI0] (0000:00) 
<br> PCI: Probing PCI hardware (bus 00) <br> ACPI: Assume root bridge [\_SB_.PCI0] segment is 0 <br> PCI: Transparent bridge - 0000:00:09.0 <br> Boot video device is 0000:01:00.0 <br> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] 
<br> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] <br> ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <br> ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. 
<br> ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 7 9 10 11 12 14 15) <br> ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <br> ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. 
<br> ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 7 9 10 11 12 14 15) <br> ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <br> ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. 
<br> ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15) <br> ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <br> ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15) 
<br> ACPI: PCI Interrupt Link [LUB2] (IRQs *3 4 5 7 9 10 11 12 14 15) <br> ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <br> ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 *5 7 9 10 11 12 14 15) 
<br> ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15) <br> ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <br> ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. <br> ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. 
<br> ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. <br> ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. <br> ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. <br> ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. 
<br> ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. 
<br> ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. 
<br> ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. <br> ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. <br> Linux Plug and Play Support v0.97 (c) Adam Belay <br> pnp: PnP ACPI init <br>
 pnp: PnP ACPI: found 14 devices <br> SCSI subsystem initialized <br> usbcore: registered new driver usbfs <br> usbcore: registered new driver hub <br> PCI: Using ACPI for IRQ routing <br> PCI: If a device doesn&#39;t work, try &quot;pci=routeirq&quot;.&nbsp;&nbsp;If it helps, post a report 
<br> pnp: 00:00: ioport range 0x4000-0x407f could not be reserved <br> pnp: 00:00: ioport range 0x4080-0x40ff has been reserved <br> pnp: 00:00: ioport range 0x4400-0x447f has been reserved <br> pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved 
<br> pnp: 00:00: ioport range 0x4800-0x487f has been reserved <br> pnp: 00:00: ioport range 0x4880-0x48ff has been reserved <br> PCI: Bridge: 0000:00:09.0 <br>&nbsp;&nbsp; IO window: a000-afff <br>&nbsp;&nbsp; MEM window: d0000000-d1ffffff <br>
&nbsp;&nbsp; PREFETCH window: 20000000-200fffff <br> PCI: Bridge: 0000:00:0b.0 <br>&nbsp;&nbsp; IO window: disabled. <br>&nbsp;&nbsp; MEM window: disabled. <br>&nbsp;&nbsp; PREFETCH window: disabled. <br> PCI: Bridge: 0000:00:0c.0 <br>&nbsp;&nbsp; IO window: disabled. <br>
&nbsp;&nbsp; MEM window: disabled. <br>&nbsp;&nbsp; PREFETCH window: disabled. <br> PCI: Bridge: 0000:00:0d.0 <br>&nbsp;&nbsp; IO window: disabled. <br>&nbsp;&nbsp; MEM window: disabled. <br>&nbsp;&nbsp; PREFETCH window: disabled. <br> PCI: Bridge: 0000:00:0e.0 <br>&nbsp;&nbsp; IO window: disabled. 
<br>&nbsp;&nbsp; MEM window: c8000000-cfffffff <br>&nbsp;&nbsp; PREFETCH window: c0000000-c7ffffff <br> PCI: Setting latency timer of device 0000:00:09.0 to 64 <br> PCI: Setting latency timer of device 0000:00:0b.0 to 64 <br> PCI: Setting latency timer of device 0000:00:
0c.0 to 64 <br> PCI: Setting latency timer of device 0000:00:0d.0 to 64 <br> PCI: Setting latency timer of device 0000:00:0e.0 to 64 <br> Machine check exception polling timer started. <br> audit: initializing netlink socket (disabled) 
<br> audit(1189637059.259:1): initialized <br> NTFS driver 2.1.23 [Flags: R/O]. <br> Initializing Cryptographic API <br> PCI: Setting latency timer of device 0000:00:0b.0 to 64 <br> pcie_portdrv_probe-&gt;Dev[005d:10de] has invalid IRQ. Check vendor BIOS 
<br> assign_interrupt_mode Found MSI capability <br> Allocate Port Service[pcie00] <br> PCI: Setting latency timer of device 0000:00:0c.0 to 64 <br> pcie_portdrv_probe-&gt;Dev[005d:10de] has invalid IRQ. Check vendor BIOS 
<br> assign_interrupt_mode Found MSI capability <br> Allocate Port Service[pcie00] <br> PCI: Setting latency timer of device 0000:00:0d.0 to 64 <br> pcie_portdrv_probe-&gt;Dev[005d:10de] has invalid IRQ. Check vendor BIOS 
<br> assign_interrupt_mode Found MSI capability <br> Allocate Port Service[pcie00] <br> PCI: Setting latency timer of device 0000:00:0e.0 to 64 <br> pcie_portdrv_probe-&gt;Dev[005d:10de] has invalid IRQ. Check vendor BIOS 
<br> assign_interrupt_mode Found MSI capability <br> Allocate Port Service[pcie00] <br> lp: driver loaded but no devices found <br> [drm] Initialized drm 1.0.0 20040925 <br> vesafb: NVIDIA Corporation, nv43 Board - p216h0&nbsp;&nbsp;, Chip Rev&nbsp;&nbsp;&nbsp;&nbsp;(OEM: NVIDIA) 
<br> vesafb: VBE version: 3.0 <br> vesafb: protected mode interface info at c000:d600 <br> vesafb: pmi: set display start = c00cd636, set palette = c00cd6a0 <br> vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
<br> vesafb: hardware supports DDC2 transfers <br> vesafb: monitor limits: vf = 76 Hz, hf = 82 kHz, clk = 140 MHz <br> vesafb: scrolling: ywrap using protected mode interface, yres_virtual=8987 <br> Console: switching to colour frame buffer device 175x65 
<br> vesafb: framebuffer at 0xc0000000, mapped to 0xe0880000, using 24576k, total 131072k <br> fb0: VESA VGA frame buffer device <br> ACPI: Power Button (FF) [PWRF] <br> ACPI: Power Button (CM) [PWRB] <br> ACPI: Fan [FAN] (on) 
<br> ACPI: CPU0 (power states: C1[C1]) <br> ACPI: Processor [CPU0] (supports 8 throttling states) <br> ACPI: Thermal Zone [THRM] (40 C) <br> PNP: PS/2 controller doesn&#39;t have AUX irq; using default 0xc <br> PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112 
<br> serio: i8042 AUX port at 0x60,0x64 irq 12 <br> serio: i8042 KBD port at 0x60,0x64 irq 1 <br> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled <br> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <br>
 ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <br> parport: PnPBIOS parport detected. <br> parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)] <br> lp0: using parport0 (interrupt-driven). <br> mice: PS/2 mouse device common for all mice 
<br> io scheduler noop registered <br> io scheduler anticipatory registered <br> io scheduler deadline registered <br> io scheduler cfq registered <br> input: AT Translated Set 2 keyboard on isa0060/serio0 <br> input: PS/2 Generic Mouse on isa0060/serio1 
<br> floppy0: no floppy controllers found <br> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize <br> loop: loaded (max 8 devices) <br> forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35
. <br> PPP generic driver version 2.4.2 <br> PPP Deflate Compression module registered <br> PPP BSD Compression module registered <br> NET: Registered protocol family 24 <br> 8139too Fast Ethernet driver 0.9.27 <br> ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 3 
<br> PCI: setting IRQ 3 as level-triggered <br> ACPI: PCI Interrupt 0000:05:08.0[A] -&gt; Link [LNK3] -&gt; GSI 3 (level, low) -&gt; IRQ 3 <br> eth0: RealTek RTL8139 at 0xe0802000, 00:0a:eb:4b:36:48, IRQ 3 <br> eth0:&nbsp;&nbsp;Identified 8139 chip type &#39;RTL-8100B/8139D&#39; 
<br> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 <br> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <br> NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 <br> NFORCE-CK804: chipset revision 242 
<br> NFORCE-CK804: not 100% native mode: will probe irqs later <br> NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller <br>&nbsp;&nbsp;&nbsp;&nbsp; ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA <br>&nbsp;&nbsp;&nbsp;&nbsp; ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA 
<br> Probing IDE interface ide0... <br> hda: PIONEER DVD-RW DVR-110, ATAPI CD/DVD-ROM drive <br> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <br> Probing IDE interface ide1... <br> Probing IDE interface ide1... <br> hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache, UDMA(66) 
<br> Uniform CD-ROM driver Revision: 3.20 <br> libata version 1.12 loaded. <br><span style="color: rgb(204, 0, 0);"> sata_nv version 0.8 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ACPI: PCI Interrupt Link [LSID] enabled at IRQ 5 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> PCI: setting IRQ 5 as level-triggered </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ACPI: PCI Interrupt 0000:00:
07.0[A] -&gt; Link [LSID] -&gt; GSI 5 (level, low) -&gt; IRQ 5 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> PCI: Setting latency timer of device 0000:00:07.0 to 64 </span><br style="color: rgb(204, 0, 0);">
<span style="color: rgb(204, 0, 0);"> ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD400 irq 5 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD408 irq 5 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata1: no device found (phy stat 00000000) </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> scsi0 : sata_nv </span>
<br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata2: no device found (phy stat 00000000) </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> scsi1 : sata_nv </span><br style="color: rgb(204, 0, 0);">
<span style="color: rgb(204, 0, 0);"> ACPI: PCI Interrupt Link [LFID] enabled at IRQ 11 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> PCI: setting IRQ 11 as level-triggered </span><br style="color: rgb(204, 0, 0);">
<span style="color: rgb(204, 0, 0);"> ACPI: PCI Interrupt 0000:00:08.0[A] -&gt; Link [LFID] -&gt; GSI 11 (level, low) -&gt; IRQ 11 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> PCI: Setting latency timer of device 0000:00:
08.0 to 64 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC000 irq 11 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);">
 ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC008 irq 11 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata3: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4773 85:7c68 86:3e01 87:4763 88:407f 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata3: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> nv_sata: Primary device added 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> nv_sata: Primary device removed </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> nv_sata: Secondary device added 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> nv_sata: Secondary device removed </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata3: dev 0 configured for UDMA/133 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> scsi2 : sata_nv </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> ata4: no device found (phy stat 00000000) </span>
<br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> scsi3 : sata_nv </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);">&nbsp;&nbsp; Vendor: ATA&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Model: Maxtor 6V160E0&nbsp;&nbsp;&nbsp;&nbsp;Rev: VA11 
</span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);">&nbsp;&nbsp; Type:&nbsp;&nbsp; Direct-Access&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;ANSI SCSI revision: 05 </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);">
 SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> SCSI device sda: drive cache: write back </span><br style="color: rgb(204, 0, 0);">
<span style="color: rgb(204, 0, 0);"> SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) </span><br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);"> SCSI device sda: drive cache: write back </span>
<br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);">&nbsp;&nbsp;sda: sda1 sda2 &lt; sda5 sda6 sda7 sda8 sda9 sda10 sda11 &gt; </span><br> Attached scsi disk sda at scsi2, channel 0, id 0, lun 0 <br> Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0,&nbsp;&nbsp;type 0 
<br> ieee1394: raw1394: /dev/raw1394 device initialized <br> ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 3 <br> ACPI: PCI Interrupt 0000:00:02.1[B] -&gt; Link [LUB2] -&gt; GSI 3 (level, low) -&gt; IRQ 3 <br> PCI: Setting latency timer of device 0000:00:
02.1 to 64 <br> ehci_hcd 0000:00:02.1: nVidia Corporation CK804 USB Controller <br> ehci_hcd 0000:00:02.1: debug port 1 <br> ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 <br> ehci_hcd 0000:00:02.1: irq 3, io mem 0xd2004000 
<br> PCI: cache line size of 64 is not supported by device 0000:00:02.1 <br> ehci_hcd 0000:00:02.1: park 0 <br> ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 <br> hub 1-0:1.0: USB hub found <br>
 hub 1-0:1.0: 10 ports detected <br> ohci_hcd: 2005 April 22 USB 1.1 &#39;Open&#39; Host Controller (OHCI) Driver (PCI) <br> ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 5 <br> ACPI: PCI Interrupt 0000:00:02.0[A] -&gt; Link [LUBA] -&gt; GSI 5 (level, low) -&gt; IRQ 5 
<br> PCI: Setting latency timer of device 0000:00:02.0 to 64 <br> ohci_hcd 0000:00:02.0: nVidia Corporation CK804 USB Controller <br> ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 <br> ohci_hcd 0000:00:
02.0: irq 5, io mem 0xd2003000 <br> hub 2-0:1.0: USB hub found <br> hub 2-0:1.0: 10 ports detected <br> Initializing USB Mass Storage driver... <br> usbcore: registered new driver usb-storage <br> USB Mass Storage support registered. 
<br> usb 2-1: new low speed USB device using ohci_hcd and address 2 <br> usbcore: registered new driver hiddev <br> input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1
 <br> usbcore: registered new driver usbhid <br> drivers/usb/input/hid-core.c: v2.01:USB HID core driver <br> NET: Registered protocol family 2 <br> IP route cache hash table entries: 8192 (order: 3, 32768 bytes) <br> TCP established hash table entries: 32768 (order: 6, 262144 bytes) 
<br> TCP bind hash table entries: 32768 (order: 5, 131072 bytes) <br> TCP: Hash tables configured (established 32768 bind 32768) <br> TCP reno registered <br> ip_conntrack version 2.1 (4095 buckets, 32760 max) - 212 bytes per conntrack 
<br> ip_tables: (C) 2000-2002 Netfilter core team <br> ipt_recent v0.3.1: Stephen Frost &lt;<a href="mailto:sfrost@...">sfrost@...</a>&gt;.&nbsp;&nbsp;<a href="http://snowman.net/projects/ipt_recent/">http://snowman.net/projects/ipt_recent/
</a> <br> arp_tables: (C) 2002 David S. Miller <br> TCP bic registered <br> NET: Registered protocol family 1 <br> NET: Registered protocol family 17 <br> powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3
) <br> powernow-k8: BIOS error - no PSB or ACPI _PSS objects <br> Using IPI Shortcut mode <br> ACPI wakeup devices: <br> HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1 <br> ACPI: (supports S0 S1 S3 S4 S5) <br> ReiserFS: sda9: found reiserfs format &quot;
3.6&quot; with standard journal <br> ReiserFS: sda9: using ordered data mode <br>ReiserFS: sda9: journal params: device sda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 
<br> ReiserFS: sda9: checking transaction log (sda9) <br> ReiserFS: sda9: Using r5 hash to sort names <br> VFS: Mounted root (reiserfs filesystem) readonly. <br> Freeing unused kernel memory: 180k freed <br> nvidia: module license &#39;NVIDIA&#39; taints kernel. 
<br> ACPI: PCI Interrupt 0000:01:00.0[A] -&gt; Link [LNK3] -&gt; GSI 3 (level, low) -&gt; IRQ 3 <br> PCI: Setting latency timer of device 0000:01:00.0 to 64 <br> NVRM: loading NVIDIA Linux x86 Kernel Module&nbsp;&nbsp;1.0-9639&nbsp;&nbsp;Mon Apr 16 20:20:06 PDT 2007 
<br> ReiserFS: sda10: found reiserfs format &quot;3.6&quot; with standard journal <br> ReiserFS: sda10: using ordered data mode <br>ReiserFS: sda10: journal params: device sda10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 
<br> ReiserFS: sda10: checking transaction log (sda10) <br> ReiserFS: sda10: Using r5 hash to sort names <br> NTFS volume version 3.1. <br> NTFS volume version 3.1. <br> fuse init (API version 7.8) <br> fuse distribution version: 
2.7.0 <br> Adding 1052216k swap on /dev/sda11.&nbsp;&nbsp;Priority:-1 extents:1 <br> ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11 <br> ACPI: PCI Interrupt 0000:00:04.0[A] -&gt; Link [LACI] -&gt; GSI 11 (level, low) -&gt; IRQ 11 
<br> PCI: Setting latency timer of device 0000:00:04.0 to 64 <br> intel8x0_measure_ac97_clock: measured 50582 usecs <br> intel8x0: clocking to 46841 <br> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <br> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 
<br> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <br> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <br></div> 	 <br>I tried dmesg also in Gentoo LiveCD 2006.0 and Gentoo LiveCD 2007.0, couldnt find any trace of scsi device. But in Kubuntu 
7.04 i got it (let me cut this down a little of bit this time, it&#39;s too long, you can get the full output from <a href="http://punkid.cn/glade/kubuntu-info.txt">here</a> which features the dmesg,lspci and lsmod output) 
<br>&nbsp;&nbsp;&nbsp;  <br><div style="margin-left: 40px;"> [&nbsp;&nbsp;&nbsp;&nbsp;0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (Ubuntu 2.6.20-15.27-generic) <br>
 ... <br> [&nbsp;&nbsp; 33.281791] SCSI subsystem initialized <br> [&nbsp;&nbsp; 33.286398] libata version 2.20 loaded. <br> [&nbsp;&nbsp; 33.289865] sata_nv 0000:00:07.0: version 3.3 <br> [&nbsp;&nbsp; 33.290394] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21 
<br> [&nbsp;&nbsp; 33.290402] ACPI: PCI Interrupt 0000:00:07.0[A] -&gt; Link [APSI] -&gt; GSI 21 (level, low) -&gt; IRQ 18 <br> [&nbsp;&nbsp; 33.290411] sata_nv 0000:00:07.0: Using ADMA mode <br> [&nbsp;&nbsp; 33.290423] PCI: Setting latency timer of device 0000:00:
07.0 to 64 <br> [&nbsp;&nbsp; 33.290501] ata1: SATA max UDMA/133 cmd 0xe0856480 ctl 0xe08564a0 bmdma 0x0001d400 irq 18 <br> [&nbsp;&nbsp; 33.290543] ata2: SATA max UDMA/133 cmd 0xe0856580 ctl 0xe08565a0 bmdma 0x0001d408 irq 18 <br> [&nbsp;&nbsp; 33.290554
] scsi0 : sata_nv <br> [&nbsp;&nbsp; 33.607099] ata1: SATA link down (SStatus 0 SControl 300) <br> [&nbsp;&nbsp; 33.607116] scsi1 : sata_nv <br> [&nbsp;&nbsp; 33.846693] usb 1-1: new low speed USB device using ohci_hcd and address 2 <br> [&nbsp;&nbsp; 33.922566
] ata2: SATA link down (SStatus 0 SControl 300) <br> [&nbsp;&nbsp; 33.923770] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20 <br> [&nbsp;&nbsp; 33.923777] ACPI: PCI Interrupt 0000:00:08.0[A] -&gt; Link [APSJ] -&gt; GSI 20 (level, low) -&gt; IRQ 19 
<br> [&nbsp;&nbsp; 33.923787] sata_nv 0000:00:08.0: Using ADMA mode <br> [&nbsp;&nbsp; 33.923800] PCI: Setting latency timer of device 0000:00:08.0 to 64 <br> [&nbsp;&nbsp; 33.923870] ata3: SATA max UDMA/133 cmd 0xe0862480 ctl 0xe08624a0 bmdma 0x0001c000 irq 19 
<br> [&nbsp;&nbsp; 33.923913] ata4: SATA max UDMA/133 cmd 0xe0862580 ctl 0xe08625a0 bmdma 0x0001c008 irq 19 <br> [&nbsp;&nbsp; 33.923925] scsi2 : sata_nv <br> [&nbsp;&nbsp; 34.052254] usb 1-1: configuration #1 chosen from 1 choice <br> [&nbsp;&nbsp; 34.066871] usbcore: registered new interface driver hiddev 
<br> [&nbsp;&nbsp; 34.072392] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2 <br> [&nbsp;&nbsp; 34.072498] input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:
02.0-1 <br> [&nbsp;&nbsp; 34.072513] usbcore: registered new interface driver usbhid <br> [&nbsp;&nbsp; 34.072516] drivers/usb/input/hid-core.c: v2.6:USB HID core driver <br> [&nbsp;&nbsp; 34.397786] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 
<br> [&nbsp;&nbsp; 34.410822] ata3.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808 <br> [&nbsp;&nbsp; 34.410827] ata3.00: ATA-7: Maxtor 6V160E0, VA111630, max UDMA/133 <br> [&nbsp;&nbsp; 34.410830] ata3.00: 312581808 sectors, multi 1: LBA48 NCQ (depth 31/32) 
<br> [&nbsp;&nbsp; 34.422784] ata3.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808 <br> [&nbsp;&nbsp; 34.422788] ata3.00: configured for UDMA/133 <br> [&nbsp;&nbsp; 34.422797] scsi3 : sata_nv <br> [&nbsp;&nbsp; 34.737207] ata4: SATA link down (SStatus 0 SControl 300) 
<br> [&nbsp;&nbsp; 34.737983] scsi 2:0:0:0: Direct-Access&nbsp;&nbsp;&nbsp;&nbsp; ATA&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Maxtor 6V160E0&nbsp;&nbsp; VA11 PQ: 0 ANSI: 5 <br> [&nbsp;&nbsp; 34.737992] ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 <br> [&nbsp;&nbsp; 34.739951] NFORCE-CK804: IDE controller at PCI slot 0000:00:
06.0 <br> [&nbsp;&nbsp; 34.739971] NFORCE-CK804: chipset revision 242 <br> [&nbsp;&nbsp; 34.739973] NFORCE-CK804: not 100% native mode: will probe irqs later <br> [&nbsp;&nbsp; 34.739979] NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller <br> [&nbsp;&nbsp; 
34.739988]&nbsp;&nbsp;&nbsp;&nbsp; ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA <br> [&nbsp;&nbsp; 34.739996]&nbsp;&nbsp;&nbsp;&nbsp; ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA <br> [&nbsp;&nbsp; 34.740003] Probing IDE interface ide0... <br> [&nbsp;&nbsp; 
34.758729] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) <br> [&nbsp;&nbsp; 34.758742] sda: Write Protect is off <br> [&nbsp;&nbsp; 34.758745] sda: Mode Sense: 00 3a 00 00 <br> [&nbsp;&nbsp; 34.758758] SCSI device sda: write cache: enabled, read cache: enabled, doesn&#39;t support DPO or FUA 
<br> [&nbsp;&nbsp; 34.758807] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) <br> [&nbsp;&nbsp; 34.758815] sda: Write Protect is off <br> [&nbsp;&nbsp; 34.758817] sda: Mode Sense: 00 3a 00 00 <br> [&nbsp;&nbsp; 34.758830] SCSI device sda: write cache: enabled, read cache: enabled, doesn&#39;t support DPO or FUA 
<br> [&nbsp;&nbsp; 34.758833]&nbsp;&nbsp;sda: sda1 sda2 &lt; sda5 sda6 sda7 sda8 sda9 sda10 sda11 &gt; <br> [&nbsp;&nbsp; 34.862086] sd 2:0:0:0: Attached scsi disk sda <br> [&nbsp;&nbsp; 34.865814] sd 2:0:0:0: Attached scsi generic sg0 type 0 <br>&nbsp;&nbsp;<br> [&nbsp;&nbsp;115.268000
] ReiserFS: sda9: found reiserfs format &quot;3.6&quot; with standard journal <br> [&nbsp;&nbsp;115.268000] ReiserFS: sda9: using ordered data mode <br>[&nbsp;&nbsp;115.276000] ReiserFS: sda9: journal params: device sda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 
<br> [&nbsp;&nbsp;115.276000] ReiserFS: sda9: checking transaction log (sda9) <br> [&nbsp;&nbsp;115.352000] ReiserFS: sda9: Using r5 hash to sort names <br> ... <br></div> 	 <br> and i confirmed it with fdisk -l /dev/sda under Kubuntu <br>&nbsp; 
<br><div style="margin-left: 40px;"> Disk /dev/sda: 160.0 GB, 160041885696 bytes <br> 255 heads, 63 sectors/track, 19457 cylinders <br> Units = cylinders of 16065 * 512 = 8225280 bytes <br>&nbsp;&nbsp;<br>&nbsp;&nbsp;&nbsp;&nbsp;Device Boot&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Start&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; End&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Blocks&nbsp;&nbsp; Id&nbsp;&nbsp;System 
<br> /dev/sda1&nbsp;&nbsp; *&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 1&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;2611&nbsp;&nbsp;&nbsp;&nbsp;20972826&nbsp;&nbsp;&nbsp;&nbsp;7&nbsp;&nbsp;HPFS/NTFS <br> /dev/sda2&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;2612&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 19456&nbsp;&nbsp; 135307462+&nbsp;&nbsp; f&nbsp;&nbsp;W95 Ext&#39;d (LBA) <br> /dev/sda5&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;2612&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;5222&nbsp;&nbsp;&nbsp;&nbsp;20972826&nbsp;&nbsp;&nbsp;&nbsp;7&nbsp;&nbsp;HPFS/NTFS 
<br> /dev/sda6&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;5223&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;9138&nbsp;&nbsp;&nbsp;&nbsp;31455238+&nbsp;&nbsp; 7&nbsp;&nbsp;HPFS/NTFS <br> /dev/sda7&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;9139&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15976&nbsp;&nbsp;&nbsp;&nbsp;54926203+&nbsp;&nbsp; 7&nbsp;&nbsp;HPFS/NTFS <br> /dev/sda8&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15977&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15981&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 40131&nbsp;&nbsp; 83&nbsp;&nbsp;Linux <br> /dev/sda9&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15982&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 18276&nbsp;&nbsp;&nbsp;&nbsp;18434556&nbsp;&nbsp; 83&nbsp;&nbsp;Linux 
<br> /dev/sda10&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;18277&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 19325&nbsp;&nbsp;&nbsp;&nbsp; 8426061&nbsp;&nbsp; 83&nbsp;&nbsp;Linux <br> /dev/sda11&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;19326&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 19456&nbsp;&nbsp;&nbsp;&nbsp; 1052226&nbsp;&nbsp; 82&nbsp;&nbsp;Linux swap / Solaris <br></div> 	 &nbsp;<br>And definitely let me show you my kernel config in gentoo-sources-2.6.22-r6
 (which fails with a VFS error), here&#39;s the necessary setting i enabled with built-in support for sata device, you can also check the whole kernel config <a href="http://punkid.cn/glade/config-2.6.22-gentoo-r6.txt">here
</a> <br>&nbsp; <br><div style="margin-left: 40px;"> # SCSI device support <br> # <br> # CONFIG_RAID_ATTRS is not set <br> CONFIG_SCSI=y <br> # CONFIG_SCSI_TGT is not set <br> # CONFIG_SCSI_NETLINK is not set <br> CONFIG_SCSI_PROC_FS=y 
<br>&nbsp;&nbsp;<br> # <br> # SCSI support type (disk, tape, CD-ROM) <br> # <br> CONFIG_BLK_DEV_SD=y <br> # CONFIG_CHR_DEV_ST is not set <br> # CONFIG_CHR_DEV_OSST is not set <br> # CONFIG_BLK_DEV_SR is not set <br> CONFIG_CHR_DEV_SG=y 
<br> # CONFIG_CHR_DEV_SCH is not set <br>&nbsp;&nbsp;<br> ... <br>&nbsp;&nbsp;<br> CONFIG_ATA=y <br> # CONFIG_ATA_NONSTANDARD is not set <br> CONFIG_ATA_ACPI=y <br> # CONFIG_SATA_AHCI is not set <br> # CONFIG_SATA_SVW is not set <br> # CONFIG_ATA_PIIX is not set 
<br> # CONFIG_SATA_MV is not set <br> CONFIG_SATA_NV=y <br>&nbsp;&nbsp;<br> ... <br>&nbsp;&nbsp;<br> # File systems <br> # <br> CONFIG_EXT2_FS=y <br> CONFIG_EXT2_FS_XATTR=y <br> CONFIG_EXT2_FS_POSIX_ACL=y <br> # CONFIG_EXT2_FS_SECURITY is not set 
<br> # CONFIG_EXT2_FS_XIP is not set <br> CONFIG_EXT3_FS=y <br> CONFIG_EXT3_FS_XATTR=y <br> # CONFIG_EXT3_FS_POSIX_ACL is not set <br> # CONFIG_EXT3_FS_SECURITY is not set <br> # CONFIG_EXT4DEV_FS is not set <br> CONFIG_JBD=y 
<br> # CONFIG_JBD_DEBUG is not set <br> CONFIG_FS_MBCACHE=y <br> CONFIG_REISERFS_FS=y <br> # CONFIG_REISERFS_CHECK is not set <br> # CONFIG_REISERFS_PROC_INFO is not set <br> # CONFIG_REISERFS_FS_XATTR is not set <br> ... 
<br></div> 	 <br> To confirm it&#39;s not the prob of kernel itself, i diffed the ata section between vanilla-kernel and ubuntu kernel, there&#39;s no special patches for ubuntu kernel, and actually Fedora 7 LiveCD&#39;s kernel is quite the same as vanilla-kernel. So its not the prob of kernel itself, in i say. 
<br>&nbsp;&nbsp;<br> IMHO, maybe its the compatibility prob between the ASUS K8N4-E mainboard and Gentoo system, forget my silly words if i were wrong, cuz at least kernels&lt;=2.6.13 work well in my Gentoo system&nbsp;&nbsp;please share your ideas with me and help me out of this looooooooooooong time prob. Thx for your patience and enthusiastic help. 
<br>&nbsp;&nbsp; 
Replies:
Re: Kernels (>2.6.13) dont recognize my sata disk on K8N4-E
-- Luca Barbato
Re: Kernels (>2.6.13) dont recognize my sata disk on K8N4-E
-- George Prowse
Navigation:
Lists: gentoo-kernel: < Prev By Thread Next > < Prev By Date Next >
Previous by thread:
linux-2.6.22-gentoo-r5 missing 'kernel' subtree?
Next by thread:
Re: Kernels (>2.6.13) dont recognize my sata disk on K8N4-E
Previous by date:
Re: linux-2.6.22-gentoo-r5 missing 'kernel' subtree?
Next by date:
Re: Kernels (>2.6.13) dont recognize my sata disk on K8N4-E


Updated Jun 17, 2009

Summary: Archive of the gentoo-kernel mailing list.

Donate to support our development efforts.

Copyright 2001-2013 Gentoo Foundation, Inc. Questions, Comments? Contact us.