Gentoo Archives: gentoo-laptop

From: "Alessandro D.M. Semeria" <goloiat@××××××.it>
To: gentoo-laptop@l.g.o
Cc: gthb@×××××.net
Subject: Re: [gentoo-laptop] cardbus usb2 not working
Date: Fri, 26 Nov 2004 20:49:23
Message-Id: 20041126215001.1024fe5d.goloiat@libero.it
In Reply to: Re: [gentoo-laptop] cardbus usb2 not working by "Guðni Þ. Björgvinsson"
Dmesg output when I plug cardbus:

Linux PCMCIA Card Services 3.2.5
  kernel build: 2.4.26-gentoo-r9 #11 Sun Oct 10 14:57:14 CEST 2004
  options:  [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Enabling device 00:0b.0 (0000 -> 0002)
PCI: No IRQ known for interrupt pin A of device 00:0b.0 - using IRQ 255
PCI: Enabling device 00:0b.1 (0000 -> 0002)
PCI: No IRQ known for interrupt pin B of device 00:0b.1 - using IRQ 255
  Toshiba ToPIC100 rev 20 PCI-to-CardBus at slot 00:0b, mem 0x10000000
    host opts [0]: [slot 0xd0] [ccr 0x11] [cdr 0x86] [rcr 0xc000000] [no pci irq] [lat 64/176] [bus 20/20]
    host opts [1]: [slot 0xd0] [ccr 0x21] [cdr 0x86] [rcr 0xc000000] [no pci irq] [lat 64/176] [bus 21/21]
    ISA irqs (default) = 4,5,7,10,12 polling interval = 1000 ms
When I plug the hard disk no messages.

My kernel config about usb and scsi (the usb to serial configuration is for the usb-gprs connection and palm sync):


# USB support
#
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_UHCI_ALT=y
CONFIG_USB_OHCI=y
CONFIG_USB_STORAGE=m
CONFIG_USB_PRINTER=m

# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_PL2303=m


# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=m

Thanks

A.S.

On Fri, 26 Nov 2004 17:03:04 +0000
Guðni Þ. Björgvinsson <gthb@×××××.net> wrote:

> Do you have the necessary support for usb and scsi emulation in the > kernel? What does dmesg tell you when you plug in the usb disk? > > On Fri, 2004-11-26 at 17:38 +0100, Alessandro D.M. Semeria wrote: > > I'd use a cradbus-usb2 to connect with an external > > usb2 hard-disk, but kernel seem to was not able to handle this > > device. > > My laptop-box: > > > > Linux ulisse 2.4.26-gentoo-r9 i686 Pentium III (Coppermine) > > GenuineIntel GNU/Linux > > > > -- > > gentoo-laptop@g.o mailing list > > > > > -- > gentoo-laptop@g.o mailing list >
-- gentoo-laptop@g.o mailing list