| 1 |
Hi Devon, |
| 2 |
|
| 3 |
> Please run lsusb -v on the Debian system with the USB drive installed. |
| 4 |
|
| 5 |
this is the relevant result of lsusb -v in the Debian system: |
| 6 |
|
| 7 |
Bus 004 Device 004: ID 0402:5642 ALi Corp. |
| 8 |
Device Descriptor: |
| 9 |
bLength 18 |
| 10 |
bDescriptorType 1 |
| 11 |
bcdUSB 2.00 |
| 12 |
bDeviceClass 0 (Defined at Interface level) |
| 13 |
bDeviceSubClass 0 |
| 14 |
bDeviceProtocol 0 |
| 15 |
bMaxPacketSize0 64 |
| 16 |
idVendor 0x0402 ALi Corp. |
| 17 |
idProduct 0x5642 |
| 18 |
bcdDevice 1.00 |
| 19 |
iManufacturer 0 |
| 20 |
iProduct 1 USB 2.0 Storage Device |
| 21 |
iSerial 2 12345678901234567890 |
| 22 |
bNumConfigurations 1 |
| 23 |
Configuration Descriptor: |
| 24 |
bLength 9 |
| 25 |
bDescriptorType 2 |
| 26 |
wTotalLength 32 |
| 27 |
bNumInterfaces 1 |
| 28 |
bConfigurationValue 1 |
| 29 |
iConfiguration 0 |
| 30 |
bmAttributes 0xc0 |
| 31 |
Self Powered |
| 32 |
MaxPower 0mA |
| 33 |
Interface Descriptor: |
| 34 |
bLength 9 |
| 35 |
bDescriptorType 4 |
| 36 |
bInterfaceNumber 0 |
| 37 |
bAlternateSetting 0 |
| 38 |
bNumEndpoints 2 |
| 39 |
bInterfaceClass 8 Mass Storage |
| 40 |
bInterfaceSubClass 6 SCSI |
| 41 |
bInterfaceProtocol 80 Bulk (Zip) |
| 42 |
iInterface 0 |
| 43 |
Endpoint Descriptor: |
| 44 |
bLength 7 |
| 45 |
bDescriptorType 5 |
| 46 |
bEndpointAddress 0x01 EP 1 OUT |
| 47 |
bmAttributes 2 |
| 48 |
Transfer Type Bulk |
| 49 |
Synch Type None |
| 50 |
Usage Type Data |
| 51 |
wMaxPacketSize 0x0200 1x 512 bytes |
| 52 |
bInterval 0 |
| 53 |
Endpoint Descriptor: |
| 54 |
bLength 7 |
| 55 |
bDescriptorType 5 |
| 56 |
bEndpointAddress 0x82 EP 2 IN |
| 57 |
bmAttributes 2 |
| 58 |
Transfer Type Bulk |
| 59 |
Synch Type None |
| 60 |
Usage Type Data |
| 61 |
wMaxPacketSize 0x0200 1x 512 bytes |
| 62 |
bInterval 1 |
| 63 |
Device Qualifier (for other device speed): |
| 64 |
bLength 10 |
| 65 |
bDescriptorType 6 |
| 66 |
bcdUSB 2.00 |
| 67 |
bDeviceClass 0 (Defined at Interface level) |
| 68 |
bDeviceSubClass 0 |
| 69 |
bDeviceProtocol 0 |
| 70 |
bMaxPacketSize0 64 |
| 71 |
bNumConfigurations 1 |
| 72 |
Device Status: 0x0001 |
| 73 |
Self Powered |
| 74 |
|
| 75 |
Bus 004 Device 001: ID 0000:0000 |
| 76 |
Device Descriptor: |
| 77 |
bLength 18 |
| 78 |
bDescriptorType 1 |
| 79 |
bcdUSB 2.00 |
| 80 |
bDeviceClass 9 Hub |
| 81 |
bDeviceSubClass 0 Unused |
| 82 |
bDeviceProtocol 1 Single TT |
| 83 |
bMaxPacketSize0 64 |
| 84 |
idVendor 0x0000 |
| 85 |
idProduct 0x0000 |
| 86 |
bcdDevice 2.06 |
| 87 |
iManufacturer 3 Linux 2.6.17-2-686 ehci_hcd |
| 88 |
iProduct 2 EHCI Host Controller |
| 89 |
iSerial 1 0000:00:03.3 |
| 90 |
bNumConfigurations 1 |
| 91 |
Configuration Descriptor: |
| 92 |
bLength 9 |
| 93 |
bDescriptorType 2 |
| 94 |
wTotalLength 25 |
| 95 |
bNumInterfaces 1 |
| 96 |
bConfigurationValue 1 |
| 97 |
iConfiguration 0 |
| 98 |
bmAttributes 0xe0 |
| 99 |
Self Powered |
| 100 |
Remote Wakeup |
| 101 |
MaxPower 0mA |
| 102 |
Interface Descriptor: |
| 103 |
bLength 9 |
| 104 |
bDescriptorType 4 |
| 105 |
bInterfaceNumber 0 |
| 106 |
bAlternateSetting 0 |
| 107 |
bNumEndpoints 1 |
| 108 |
bInterfaceClass 9 Hub |
| 109 |
bInterfaceSubClass 0 Unused |
| 110 |
bInterfaceProtocol 0 Full speed hub |
| 111 |
iInterface 0 |
| 112 |
Endpoint Descriptor: |
| 113 |
bLength 7 |
| 114 |
bDescriptorType 5 |
| 115 |
bEndpointAddress 0x81 EP 1 IN |
| 116 |
bmAttributes 3 |
| 117 |
Transfer Type Interrupt |
| 118 |
Synch Type None |
| 119 |
Usage Type Data |
| 120 |
wMaxPacketSize 0x0002 1x 2 bytes |
| 121 |
bInterval 12 |
| 122 |
Hub Descriptor: |
| 123 |
bLength 11 |
| 124 |
bDescriptorType 41 |
| 125 |
nNbrPorts 8 |
| 126 |
wHubCharacteristic 0x000a |
| 127 |
No power switching (usb 1.0) |
| 128 |
Per-port overcurrent protection |
| 129 |
TT think time 8 FS bits |
| 130 |
bPwrOn2PwrGood 10 * 2 milli seconds |
| 131 |
bHubContrCurrent 0 milli Ampere |
| 132 |
DeviceRemovable 0x00 0x00 |
| 133 |
PortPwrCtrlMask 0xff 0xff |
| 134 |
Hub Port Status: |
| 135 |
Port 1: 0000.0100 power |
| 136 |
Port 2: 0000.0000 |
| 137 |
Port 3: 0000.0100 power |
| 138 |
Port 4: 0000.0100 power |
| 139 |
Port 5: 0000.0000 |
| 140 |
Port 6: 0000.0100 power |
| 141 |
Port 7: 0000.0503 highspeed power enable connect |
| 142 |
Port 8: 0000.0503 highspeed power enable connect |
| 143 |
Device Status: 0x0003 |
| 144 |
Self Powered |
| 145 |
Remote Wakeup Enabled |
| 146 |
|
| 147 |
Bus 003 Device 001: ID 0000:0000 |
| 148 |
Device Descriptor: |
| 149 |
bLength 18 |
| 150 |
bDescriptorType 1 |
| 151 |
bcdUSB 1.10 |
| 152 |
bDeviceClass 9 Hub |
| 153 |
bDeviceSubClass 0 Unused |
| 154 |
bDeviceProtocol 0 Full speed hub |
| 155 |
bMaxPacketSize0 64 |
| 156 |
idVendor 0x0000 |
| 157 |
idProduct 0x0000 |
| 158 |
bcdDevice 2.06 |
| 159 |
iManufacturer 3 Linux 2.6.17-2-686 ohci_hcd |
| 160 |
iProduct 2 OHCI Host Controller |
| 161 |
iSerial 1 0000:00:03.2 |
| 162 |
bNumConfigurations 1 |
| 163 |
Configuration Descriptor: |
| 164 |
bLength 9 |
| 165 |
bDescriptorType 2 |
| 166 |
wTotalLength 25 |
| 167 |
bNumInterfaces 1 |
| 168 |
bConfigurationValue 1 |
| 169 |
iConfiguration 0 |
| 170 |
bmAttributes 0xe0 |
| 171 |
Self Powered |
| 172 |
Remote Wakeup |
| 173 |
MaxPower 0mA |
| 174 |
Interface Descriptor: |
| 175 |
bLength 9 |
| 176 |
bDescriptorType 4 |
| 177 |
bInterfaceNumber 0 |
| 178 |
bAlternateSetting 0 |
| 179 |
bNumEndpoints 1 |
| 180 |
bInterfaceClass 9 Hub |
| 181 |
bInterfaceSubClass 0 Unused |
| 182 |
bInterfaceProtocol 0 Full speed hub |
| 183 |
iInterface 0 |
| 184 |
Endpoint Descriptor: |
| 185 |
bLength 7 |
| 186 |
bDescriptorType 5 |
| 187 |
bEndpointAddress 0x81 EP 1 IN |
| 188 |
bmAttributes 3 |
| 189 |
Transfer Type Interrupt |
| 190 |
Synch Type None |
| 191 |
Usage Type Data |
| 192 |
wMaxPacketSize 0x0002 1x 2 bytes |
| 193 |
bInterval 255 |
| 194 |
Hub Descriptor: |
| 195 |
bLength 9 |
| 196 |
bDescriptorType 41 |
| 197 |
nNbrPorts 2 |
| 198 |
wHubCharacteristic 0x0012 |
| 199 |
No power switching (usb 1.0) |
| 200 |
No overcurrent protection |
| 201 |
bPwrOn2PwrGood 1 * 2 milli seconds |
| 202 |
bHubContrCurrent 0 milli Ampere |
| 203 |
DeviceRemovable 0x00 |
| 204 |
PortPwrCtrlMask 0xff |
| 205 |
Hub Port Status: |
| 206 |
Port 1: 0000.0100 power |
| 207 |
Port 2: 0000.0100 power |
| 208 |
Device Status: 0x0003 |
| 209 |
Self Powered |
| 210 |
Remote Wakeup Enabled |
| 211 |
|
| 212 |
|
| 213 |
Bus 002 Device 001: ID 0000:0000 |
| 214 |
Device Descriptor: |
| 215 |
bLength 18 |
| 216 |
bDescriptorType 1 |
| 217 |
bcdUSB 1.10 |
| 218 |
bDeviceClass 9 Hub |
| 219 |
bDeviceSubClass 0 Unused |
| 220 |
bDeviceProtocol 0 Full speed hub |
| 221 |
bMaxPacketSize0 64 |
| 222 |
idVendor 0x0000 |
| 223 |
idProduct 0x0000 |
| 224 |
bcdDevice 2.06 |
| 225 |
iManufacturer 3 Linux 2.6.17-2-686 ohci_hcd |
| 226 |
iProduct 2 OHCI Host Controller |
| 227 |
iSerial 1 0000:00:03.1 |
| 228 |
bNumConfigurations 1 |
| 229 |
Configuration Descriptor: |
| 230 |
bLength 9 |
| 231 |
bDescriptorType 2 |
| 232 |
wTotalLength 25 |
| 233 |
bNumInterfaces 1 |
| 234 |
bConfigurationValue 1 |
| 235 |
iConfiguration 0 |
| 236 |
bmAttributes 0xe0 |
| 237 |
Self Powered |
| 238 |
Remote Wakeup |
| 239 |
MaxPower 0mA |
| 240 |
Interface Descriptor: |
| 241 |
bLength 9 |
| 242 |
bDescriptorType 4 |
| 243 |
bInterfaceNumber 0 |
| 244 |
bAlternateSetting 0 |
| 245 |
bNumEndpoints 1 |
| 246 |
bInterfaceClass 9 Hub |
| 247 |
bInterfaceSubClass 0 Unused |
| 248 |
bInterfaceProtocol 0 Full speed hub |
| 249 |
iInterface 0 |
| 250 |
Endpoint Descriptor: |
| 251 |
bLength 7 |
| 252 |
bDescriptorType 5 |
| 253 |
bEndpointAddress 0x81 EP 1 IN |
| 254 |
bmAttributes 3 |
| 255 |
Transfer Type Interrupt |
| 256 |
Synch Type None |
| 257 |
Usage Type Data |
| 258 |
wMaxPacketSize 0x0002 1x 2 bytes |
| 259 |
bInterval 255 |
| 260 |
Hub Descriptor: |
| 261 |
bLength 9 |
| 262 |
bDescriptorType 41 |
| 263 |
nNbrPorts 3 |
| 264 |
wHubCharacteristic 0x0012 |
| 265 |
No power switching (usb 1.0) |
| 266 |
No overcurrent protection |
| 267 |
bPwrOn2PwrGood 1 * 2 milli seconds |
| 268 |
bHubContrCurrent 0 milli Ampere |
| 269 |
DeviceRemovable 0x00 |
| 270 |
PortPwrCtrlMask 0xff |
| 271 |
Hub Port Status: |
| 272 |
Port 1: 0000.0303 lowspeed power enable connect |
| 273 |
Port 2: 0000.0103 power enable connect |
| 274 |
Port 3: 0000.0100 power |
| 275 |
Device Status: 0x0003 |
| 276 |
Self Powered |
| 277 |
Remote Wakeup Enabled |
| 278 |
|
| 279 |
Bus 001 Device 001: ID 0000:0000 |
| 280 |
Device Descriptor: |
| 281 |
bLength 18 |
| 282 |
bDescriptorType 1 |
| 283 |
bcdUSB 1.10 |
| 284 |
bDeviceClass 9 Hub |
| 285 |
bDeviceSubClass 0 Unused |
| 286 |
bDeviceProtocol 0 Full speed hub |
| 287 |
bMaxPacketSize0 64 |
| 288 |
idVendor 0x0000 |
| 289 |
idProduct 0x0000 |
| 290 |
bcdDevice 2.06 |
| 291 |
iManufacturer 3 Linux 2.6.17-2-686 ohci_hcd |
| 292 |
iProduct 2 OHCI Host Controller |
| 293 |
iSerial 1 0000:00:03.0 |
| 294 |
bNumConfigurations 1 |
| 295 |
Configuration Descriptor: |
| 296 |
bLength 9 |
| 297 |
bDescriptorType 2 |
| 298 |
wTotalLength 25 |
| 299 |
bNumInterfaces 1 |
| 300 |
bConfigurationValue 1 |
| 301 |
iConfiguration 0 |
| 302 |
bmAttributes 0xe0 |
| 303 |
Self Powered |
| 304 |
Remote Wakeup |
| 305 |
MaxPower 0mA |
| 306 |
Interface Descriptor: |
| 307 |
bLength 9 |
| 308 |
bDescriptorType 4 |
| 309 |
bInterfaceNumber 0 |
| 310 |
bAlternateSetting 0 |
| 311 |
bNumEndpoints 1 |
| 312 |
bInterfaceClass 9 Hub |
| 313 |
bInterfaceSubClass 0 Unused |
| 314 |
bInterfaceProtocol 0 Full speed hub |
| 315 |
iInterface 0 |
| 316 |
Endpoint Descriptor: |
| 317 |
bLength 7 |
| 318 |
bDescriptorType 5 |
| 319 |
bEndpointAddress 0x81 EP 1 IN |
| 320 |
bmAttributes 3 |
| 321 |
Transfer Type Interrupt |
| 322 |
Synch Type None |
| 323 |
Usage Type Data |
| 324 |
wMaxPacketSize 0x0002 1x 2 bytes |
| 325 |
bInterval 255 |
| 326 |
Hub Descriptor: |
| 327 |
bLength 9 |
| 328 |
bDescriptorType 41 |
| 329 |
nNbrPorts 3 |
| 330 |
wHubCharacteristic 0x0012 |
| 331 |
No power switching (usb 1.0) |
| 332 |
No overcurrent protection |
| 333 |
bPwrOn2PwrGood 1 * 2 milli seconds |
| 334 |
bHubContrCurrent 0 milli Ampere |
| 335 |
DeviceRemovable 0x00 |
| 336 |
PortPwrCtrlMask 0xff |
| 337 |
Hub Port Status: |
| 338 |
Port 1: 0000.0100 power |
| 339 |
Port 2: 0000.0100 power |
| 340 |
Port 3: 0000.0100 power |
| 341 |
Device Status: 0x0003 |
| 342 |
Self Powered |
| 343 |
Remote Wakeup Enabled |
| 344 |
this is the result of the relevant part of lsusb -v: |
| 345 |
|
| 346 |
|
| 347 |
|
| 348 |
> You mentioned that the mouse still works. Assuming you are running X, |
| 349 |
> please switch to VT1 before plugging in the device. If you are |
| 350 |
> actually experiencing a kernel oops, the stack trace will be written |
| 351 |
> to vt1. |
| 352 |
|
| 353 |
Actually the mouse is _SOMETIMES_ working. Most of the times |
| 354 |
everything hangs up... |
| 355 |
However, i'll have a look. |
| 356 |
|
| 357 |
Regards, |
| 358 |
m |
| 359 |
-- |
| 360 |
gentoo-laptop@g.o mailing list |
Archives