| 1 |
I have just installed gentoo on my ibook 12". It has dual boot with |
| 2 |
yaboot. Sometimes it works fine but sometimes, without any reason it |
| 3 |
starts as follows and stops: |
| 4 |
|
| 5 |
> NET: Registered protocol family 16 |
| 6 |
> PCI: Probing PCI hardware |
| 7 |
> PCI: Cannot allocate resource region 0 of device 0001:10:18.0 |
| 8 |
> PCI: Cannot allocate resource region 0 of device 0001:10:19.0 |
| 9 |
> SCSI subsystem initialized |
| 10 |
> usbcore: registered new driver usbfs |
| 11 |
> usbcore: registered new driver hub |
| 12 |
> Thermal assist unit not available |
| 13 |
> Registering PowerMac CPU frequency driver |
| 14 |
> Low: 599 Mhz, High: 1199 Mhz, Boot: 599 Mhz |
| 15 |
> Installing knfsd (copyright (C) 1996 okir@×××××××××.de). |
| 16 |
> NTFS driver 2.1.22 [Flags: R/W]. |
| 17 |
> inotify device minor=63 |
| 18 |
> Generic RTC Driver v1.07 |
| 19 |
> Macintosh non-volatile memory driver v1.1 |
| 20 |
> PCI: Enabling device 0000:00:10.0 (0006 -> 0007) |
| 21 |
> radeonfb: Invalid ROM signature 0 should be 0xaa55 |
| 22 |
> radeonfb: Retrieved PLL infos from Open Firmware |
| 23 |
> radeonfb: Reference=27.00 Mhz (RefDiv=12) Memory=190.00 Mhz, System=183.00 |
| 24 |
> Mhz |
| 25 |
> radeonfb: PLL min 12000 max 35000 |
| 26 |
> radeonfb: Monitor 1 type LCD found |
| 27 |
> radeonfb: EDID probed |
| 28 |
> radeonfb: Monitor 2 type no found |
| 29 |
> radeonfb: Power Management enabled for Mobility chipsets |
| 30 |
> Console: switching to colour frame buffer device 128x48 |
| 31 |
> Registered "mnca" backlight controller, level: 15/15 |
| 32 |
> radeonfb: ATI Radeon \c DDR SGRAM 32 MB |
| 33 |
> i8042.c: i8042 controller self test timeout. |
| 34 |
> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled |
| 35 |
|
| 36 |
|
| 37 |
At this point it stops and nothing happens... then I need to turn the |
| 38 |
machine off and then turn it on again. Today, in particular, I needed to |
| 39 |
do this around 10 times before it worked ... |
| 40 |
|
| 41 |
It doesn't seem to be hardware problem because macosx always works fine. |
| 42 |
Maybe there is a problem with my yaboot.conf: |
| 43 |
|
| 44 |
boot=/dev/hda2 |
| 45 |
device=/pci@f4000000/ata-6@d/disk@0: |
| 46 |
partition=5 |
| 47 |
root=/dev/hda5 |
| 48 |
timeout=30 |
| 49 |
install=/usr/lib/yaboot/yaboot |
| 50 |
magicboot=/usr/lib/yaboot/ofboot |
| 51 |
|
| 52 |
image=/boot/kernel-2.6.10 |
| 53 |
label=Linux |
| 54 |
read-only |
| 55 |
|
| 56 |
macosx=/dev/hda3 |
| 57 |
|
| 58 |
My current partition table is like that: |
| 59 |
|
| 60 |
/dev/hda1 Apple_partittion_map |
| 61 |
/dev/hda2 Apple_Bootstrap |
| 62 |
/dev/hda3 Apple_HFS |
| 63 |
/dev/hda4 swap |
| 64 |
/dev/hda5 linux partition |
| 65 |
|
| 66 |
|
| 67 |
Does anyone know what is the problem? |
| 68 |
|
| 69 |
Best regards, |
| 70 |
|
| 71 |
Flavio Leonardo Cavalcanti de Moura |
| 72 |
email: flavio@×××××××.br |
| 73 |
homepage: flavio.mat.unb.br |
| 74 |
|
| 75 |
-- |
| 76 |
gentoo-ppc-user@g.o mailing list |
Archives