RE: [gentoo-ppc-user] Problem with the initialization of gentoo on ibook 12"

[Dræven]

Try turning off both of these driverss:

Device Drivers -> Character Devices -> Serial Drivers  < > 8250/16550 and
compatible serial support Device Drivers -> Input Device Support -> Hardware
I/O ports  < > i8042 PC Keyboard Controller

Hope this helps.

---

Dræven

-----Original Message-----
From: Flavio Leonardo Cavalcanti de Moura [mailto:flavio@×××××××.br] 
Sent: Thursday, July 07, 2005 6:04 PM
To: gentoo-ppc-user@l.g.o
Cc: Flavio Leonardo Cavalcanti de Moura (MAT-GRAD)
Subject: [gentoo-ppc-user] Problem with the initialization of gentoo on
ibook 12"


I have just installed gentoo on my ibook 12". It has dual boot with
yaboot. Sometimes it works fine but sometimes, without any reason it
 starts as follows and stops:

> NET: Registered protocol family 16
> PCI: Probing PCI hardware
> PCI: Cannot allocate resource region 0 of device 0001:10:18.0
> PCI: Cannot allocate resource region 0 of device 0001:10:19.0
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Thermal assist unit not available
> Registering PowerMac CPU frequency driver
> Low: 599 Mhz, High: 1199 Mhz, Boot: 599 Mhz
> Installing knfsd (copyright (C) 1996 okir@×××××××××.de).
> NTFS driver 2.1.22 [Flags: R/W].
> inotify device  minor=63
> Generic RTC Driver v1.07
> Macintosh non-volatile memory driver v1.1
> PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
> radeonfb: Invalid ROM signature 0 should be 0xaa55
> radeonfb: Retrieved PLL infos from Open Firmware
> radeonfb: Reference=27.00 Mhz (RefDiv=12) Memory=190.00 Mhz, System=183.00
> Mhz
> radeonfb: PLL min 12000 max 35000
> radeonfb: Monitor 1 type LCD found
> radeonfb: EDID probed
> radeonfb: Monitor 2 type no found
> radeonfb: Power Management enabled for Mobility chipsets
> Console: switching to colour frame buffer device 128x48
> Registered "mnca" backlight controller, level: 15/15
> radeonfb: ATI Radeon \c DDR SGRAM 32 MB
> i8042.c: i8042 controller self test timeout.
> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing  disabled


 At this point it stops and nothing happens... then I need to turn the
machine off and then turn it on again. Today, in particular, I needed to
do this around 10 times before it worked ...

It doesn't seem to be hardware problem because macosx always works fine.
Maybe there is a problem with my yaboot.conf:

boot=/dev/hda2
device=/pci@f4000000/ata-6@d/disk@0:
partition=5
root=/dev/hda5
timeout=30
install=/usr/lib/yaboot/yaboot
magicboot=/usr/lib/yaboot/ofboot

image=/boot/kernel-2.6.10
        label=Linux
        read-only

macosx=/dev/hda3

My current partition table is like that:

/dev/hda1	Apple_partittion_map
/dev/hda2	Apple_Bootstrap
/dev/hda3	Apple_HFS
/dev/hda4	swap
/dev/hda5	linux partition


 	Does anyone know what is the problem?

 Best regards,

   	Flavio Leonardo Cavalcanti de Moura
    	email:		flavio@×××××××.br
 	homepage: 	flavio.mat.unb.br

-- 
gentoo-ppc-user@g.o mailing list




-- 
gentoo-ppc-user@g.o mailing list