1 |
在 2006-12-19二的 09:40 -0500,Will Simoneau写道: |
2 |
|
3 |
> Your kernel dumped stack and part of it is showing in your dmesg |
4 |
> fragment... please post the rest of that info, because it very likely |
5 |
> will help in figuring out what's wrong. |
6 |
|
7 |
Thank you for prompted me. Here is the full dmesg |
8 |
|
9 |
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 3.15.2 1998/11/10 10:35' |
10 |
[ 0.000000] PROMLIB: Root node compatible: |
11 |
[ 0.000000] Linux version 2.6.18-gentoo-r3 (root@×××××××××××××.com) (gcc version 3.4.5 (Gentoo Linux 3.4.5)) #11 Sun Dec 17 07:14:29 HKT 2006 |
12 |
[ 0.000000] ARCH: SUN4U |
13 |
[ 0.000000] Ethernet address: 08:00:20:b0:99:30 |
14 |
[ 0.000000] PROM: Built device tree with 48679 bytes of memory. |
15 |
[ 0.000000] On node 0 totalpages: 32142 |
16 |
[ 0.000000] DMA zone: 32142 pages, LIFO batch:7 |
17 |
[ 0.000000] CPU[0]: Caches D[sz(16384):line_sz(32)] I[sz(16384):line_sz(32)] E[sz(2097152):line_sz(64)] |
18 |
[ 0.000000] Built 1 zonelists. Total pages: 32142 |
19 |
[ 0.000000] Kernel command line: root=/dev/sda2 |
20 |
[ 0.000000] PID hash table entries: 1024 (order: 10, 8192 bytes) |
21 |
[ 0.134261] Console: colour dummy device 80x25 |
22 |
[ 0.135966] Dentry cache hash table entries: 32768 (order: 5, 262144 bytes) |
23 |
[ 0.137504] Inode-cache hash table entries: 16384 (order: 4, 131072 bytes) |
24 |
[ 0.151648] Memory: 254560k available (2560k kernel code, 976k data, 120k init) [fffff80000000000,0000000017f46000] |
25 |
[ 0.229714] Calibrating delay using timer specific routine.. 666.35 BogoMIPS (lpj=1332718) |
26 |
[ 0.230158] Mount-cache hash table entries: 512 |
27 |
[ 0.233508] NET: Registered protocol family 16 |
28 |
[ 0.244766] PCI: Probing for controllers. |
29 |
[ 0.248370] /pci@1f,0/pci@1,1: SABRE PCI Bus Module |
30 |
[ 0.248416] /pci@1f,0/pci@1: SABRE PCI Bus Module |
31 |
[ 0.253380] PCI0(PBMA): Bus running at 33MHz |
32 |
[ 0.253608] PCI0(PBMB): Bus running at 33MHz |
33 |
[ 0.253776] ebus0: [auxio] [power] [SUNW,pll] [se] [su] [su] [ecpp] [fdthree] [eeprom] [flashprom] [SUNW,CS4231] |
34 |
[ 0.257231] power: Control reg at 1fff1724000 ... powerd running. |
35 |
[ 0.258991] SCSI subsystem initialized |
36 |
[ 0.259324] usbcore: registered new driver usbfs |
37 |
[ 0.259588] usbcore: registered new driver hub |
38 |
[ 0.260568] AUXIO: Found device at /pci@1f,0/pci@1,1/ebus@1/auxio@14,726000 |
39 |
[ 0.260891] /pci@1f,0/pci@1,1/ebus@1/eeprom@14,0: Clock regs at 000001fff1000000 |
40 |
[ 0.262936] NET: Registered protocol family 2 |
41 |
[ 0.298023] IP route cache hash table entries: 2048 (order: 1, 16384 bytes) |
42 |
[ 0.298790] TCP established hash table entries: 8192 (order: 3, 65536 bytes) |
43 |
[ 0.299211] TCP bind hash table entries: 4096 (order: 2, 32768 bytes) |
44 |
[ 0.299448] TCP: Hash tables configured (established 8192 bind 4096) |
45 |
[ 0.299488] TCP reno registered |
46 |
[ 0.307212] Total HugeTLB memory allocated, 0 |
47 |
[ 0.309055] Initializing Cryptographic API |
48 |
[ 0.309118] io scheduler noop registered |
49 |
[ 0.309181] io scheduler anticipatory registered (default) |
50 |
[ 0.309252] io scheduler deadline registered |
51 |
[ 0.309376] io scheduler cfq registered |
52 |
[ 2.763446] Console: switching to mono PROM 80x34 |
53 |
[ 5.222193] lp: driver loaded but no devices found |
54 |
[ 5.269419] rtc_init: no PC rtc found |
55 |
[ 5.309221] /pci@1f,0/pci@1,1/ebus@1/su@14,3083f8: Keyboard port at 1fff13083f8, irq 6 |
56 |
[ 5.401245] /pci@1f,0/pci@1,1/ebus@1/su@14,3062f8: Mouse port at 1fff13062f8, irq 7 |
57 |
[ 5.490780] parport0: PC-style at 0x1fff13043bc (0x1fff13047bc), irq 8, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA] |
58 |
[ 5.741625] parport0: Printer, Hewlett-Packard hp LaserJet 3015 |
59 |
[ 5.908842] lp0: using parport0 (interrupt-driven). |
60 |
[ 6.045027] mice: PS/2 mouse device common for all mice |
61 |
[ 6.183845] sunhme.c:v3.00 June 23, 2006 David S. Miller (davem@×××××××××.net) |
62 |
[ 6.446394] eth0: HAPPY MEAL (PCI/CheerIO) 10/100BaseT Ethernet 08:00:20:b0:99:30 |
63 |
[ 6.796018] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 |
64 |
[ 6.941406] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
65 |
[ 7.208813] CMD646: IDE controller at PCI slot 0000:01:03.0 |
66 |
[ 7.348860] CMD646: chipset revision 3 |
67 |
[ 7.476287] CMD646: chipset revision 0x03, MultiWord DMA Force Limited |
68 |
[ 7.635645] CMD646: 100% native mode on irq 14 |
69 |
[ 7.767906] ide0: BM-DMA at 0x1fe02c00020-0x1fe02c00027, BIOS settings: hda:pio, hdb:pio |
70 |
[ 8.051049] ide1: BM-DMA at 0x1fe02c00028-0x1fe02c0002f, BIOS settings: hdc:pio, hdd:pio |
71 |
[ 8.334190] Probing IDE interface ide0... |
72 |
[ 8.343815] input: Sun Type 127 keyboard as /class/input/input0 |
73 |
[ 8.487042] input: Sun Mouse as /class/input/input1 |
74 |
[ 8.845673] hda: QUANTUM FIREBALL1280A, ATA DISK drive |
75 |
[ 9.665802] ide0 at 0x1fe02c00000-0x1fe02c00007,0x1fe02c0000a on irq 14 |
76 |
[ 9.814283] Probing IDE interface ide1... |
77 |
[ 10.213624] hdc: CRD-8322B, ATAPI CD/DVD-ROM drive |
78 |
[ 11.053513] ide1 at 0x1fe02c00010-0x1fe02c00017,0x1fe02c0001a on irq 14 (shared with ide0) |
79 |
[ 11.337021] hda: max request size: 128KiB |
80 |
[ 11.466281] hda: 2503872 sectors (1281 MB) w/83KiB Cache, CHS=2484/16/63, DMA |
81 |
[ 11.665455] hda: hda1 hda2 hda3 |
82 |
[ 11.838217] hdc: ATAPI 32X CD-ROM drive, 128kB Cache |
83 |
[ 12.022040] Uniform CD-ROM driver Revision: 3.20 |
84 |
[ 12.159289] libata version 2.00 loaded. |
85 |
[ 12.159525] sata_via 0000:02:02.0: version 2.0 |
86 |
[ 12.159561] PCI: VIA IRQ fixup for 0000:02:02.0, from 18 to 2 |
87 |
[ 12.300799] sata_via 0000:02:02.0: routed to hard irq line 2 |
88 |
[ 12.441801] ata1: SATA max UDMA/133 cmd 0x1FE02000400 ctl 0x1FE0200040A bmdma 0x1FE02000440 irq 18 |
89 |
[ 12.715904] ata2: SATA max UDMA/133 cmd 0x1FE02000410 ctl 0x1FE0200041A bmdma 0x1FE02000448 irq 18 |
90 |
[ 12.989620] scsi0 : sata_via |
91 |
[ 13.421412] ata1: SATA link down (SStatus 0 SControl 310) |
92 |
[ 13.570951] ATA: abnormal status 0x7F on port 0x1FE02000407 |
93 |
[ 13.710928] scsi1 : sata_via |
94 |
[ 14.297407] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) |
95 |
[ 14.442543] ata2.00: ATA-7, max UDMA/133, 625140335 sectors: LBA48 NCQ (depth 0/32) |
96 |
[ 14.708379] ata2.00: configured for UDMA/133 |
97 |
[ 14.839752] Vendor: ATA Model: ST3320620AS Rev: 3.AA |
98 |
[ 15.335720] Type: Direct-Access ANSI SCSI revision: 05 |
99 |
[ 15.611638] SCSI device sda: 625140335 512-byte hdwr sectors (320072 MB) |
100 |
[ 15.759459] sda: Write Protect is off |
101 |
[ 15.886427] sda: Mode Sense: 00 3a 00 00 |
102 |
[ 15.886577] SCSI device sda: drive cache: write back |
103 |
[ 16.022795] SCSI device sda: 625140335 512-byte hdwr sectors (320072 MB) |
104 |
[ 16.170584] sda: Write Protect is off |
105 |
[ 16.297434] sda: Mode Sense: 00 3a 00 00 |
106 |
[ 16.297580] SCSI device sda: drive cache: write back |
107 |
[ 16.433475] sda: sda1 sda2 sda3 |
108 |
[ 16.615811] sd 1:0:0:0: Attached scsi disk sda |
109 |
[ 16.748404] rtc_sun_init: Registered Mostek RTC driver. |
110 |
[ 16.886232] ehci_hcd 0000:02:01.2: EHCI Host Controller |
111 |
[ 17.024179] ehci_hcd 0000:02:01.2: new USB bus registered, assigned bus number 1 |
112 |
[ 17.309330] ehci_hcd 0000:02:01.2: irq 17, io mem 0x1ff00006000 |
113 |
[ 17.451556] ehci_hcd 0000:02:01.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 |
114 |
[ 17.715313] usb usb1: configuration #1 chosen from 1 choice |
115 |
[ 17.855609] hub 1-0:1.0: USB hub found |
116 |
[ 17.983082] hub 1-0:1.0: 5 ports detected |
117 |
[ 18.213877] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) |
118 |
[ 18.214144] ohci_hcd 0000:02:01.0: OHCI Host Controller |
119 |
[ 18.352069] ohci_hcd 0000:02:01.0: new USB bus registered, assigned bus number 2 |
120 |
[ 18.614743] ohci_hcd 0000:02:01.0: irq 15, io mem 0x1ff00002000 |
121 |
[ 19.316296] usb usb2: configuration #1 chosen from 1 choice |
122 |
[ 19.456816] hub 2-0:1.0: USB hub found |
123 |
[ 19.584239] hub 2-0:1.0: 3 ports detected |
124 |
[ 19.921252] usb 1-2: new high speed USB device using ehci_hcd and address 3 |
125 |
[ 20.203672] usb 1-2: configuration #1 chosen from 1 choice |
126 |
[ 20.363091] ohci_hcd 0000:02:01.1: OHCI Host Controller |
127 |
[ 20.521580] ohci_hcd 0000:02:01.1: new USB bus registered, assigned bus number 3 |
128 |
[ 20.815596] ohci_hcd 0000:02:01.1: irq 16, io mem 0x1ff00004000 |
129 |
[ 21.524234] usb usb3: configuration #1 chosen from 1 choice |
130 |
[ 21.664614] hub 3-0:1.0: USB hub found |
131 |
[ 21.792248] hub 3-0:1.0: 2 ports detected |
132 |
[ 22.233193] usb 2-1: new full speed USB device using ohci_hcd and address 2 |
133 |
[ 22.549143] usb 2-1: configuration #1 chosen from 1 choice |
134 |
[ 22.819194] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x04B8 pid 0x081E |
135 |
[ 23.149740] drivers/usb/class/usblp.c: usblp1: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1617 |
136 |
[ 23.436372] usbcore: registered new driver usblp |
137 |
[ 23.569857] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver |
138 |
[ 23.729389] Initializing USB Mass Storage driver... |
139 |
[ 24.269144] usb 2-3: new low speed USB device using ohci_hcd and address 3 |
140 |
[ 24.586761] usb 2-3: configuration #1 chosen from 1 choice |
141 |
[ 24.734770] scsi2 : SCSI emulation for USB Mass Storage devices |
142 |
[ 24.877684] usbcore: registered new driver usb-storage |
143 |
[ 25.014713] USB Mass Storage support registered. |
144 |
[ 25.148344] usb-storage: device found at 3 |
145 |
[ 25.148363] usb-storage: waiting for device to settle before scanning |
146 |
[ 25.148555] usbcore: registered new driver hiddev |
147 |
[ 25.291021] input: CHESEN PS2 to USB Converter as /class/input/input2 |
148 |
[ 25.437207] input: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-0000:02:01.0-3 |
149 |
[ 25.833686] input: CHESEN PS2 to USB Converter as /class/input/input3 |
150 |
[ 25.980221] input: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-0000:02:01.0-3 |
151 |
[ 26.272963] usbcore: registered new driver usbhid |
152 |
[ 26.407084] drivers/usb/input/hid-core.c: v2.6:USB HID core driver |
153 |
[ 26.551490] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC). |
154 |
[ 26.986597] ALSA device list: |
155 |
[ 27.108836] #0: Sun CS4231 at 0x1fff1200000, irq 10 |
156 |
[ 27.245683] TCP bic registered |
157 |
[ 27.368525] NET: Registered protocol family 1 |
158 |
[ 27.500112] NET: Registered protocol family 17 |
159 |
[ 27.639634] EXT3-fs: INFO: recovery required on readonly filesystem. |
160 |
[ 27.785050] EXT3-fs: write access will be enabled during recovery. |
161 |
[ 27.954723] kjournald starting. Commit interval 5 seconds |
162 |
[ 28.094210] EXT3-fs: recovery complete. |
163 |
[ 28.222854] EXT3-fs: mounted filesystem with ordered data mode. |
164 |
[ 28.365479] VFS: Mounted root (ext3 filesystem) readonly. |
165 |
[ 30.146288] Vendor: EPSON Model: Stylus Storage Rev: 1.00 |
166 |
[ 30.646137] Type: Direct-Access ANSI SCSI revision: 02 |
167 |
[ 30.927111] sd 2:0:0:0: Attached scsi removable disk sdb |
168 |
[ 31.088639] usb-storage: device scan complete |
169 |
[ 31.603865] Adding 594352k swap on /dev/sda1. Priority:-1 extents:1 across:594352k |
170 |
[ 32.665534] EXT3 FS on sda2, internal journal |
171 |
[ 54.055095] kjournald starting. Commit interval 5 seconds |
172 |
[ 54.056064] EXT3 FS on sda3, internal journal |
173 |
[ 54.056094] EXT3-fs: mounted filesystem with ordered data mode. |
174 |
[ 69.819619] lp0: ECP mode |
175 |
[ 70.268832] lp0: ECP mode |
176 |
[ 70.303791] lp0: ECP mode |
177 |
[ 72.020026] eth0: Link is up using internal transceiver at 100Mb/s, Full Duplex. |
178 |
[ 73.783620] Unable to load NLS charset utf-8 |
179 |
[ 73.783647] smbfs: failed to load nls 'utf-8' |
180 |
[ 1105.664443] lp0: ECP mode |
181 |
[ 1105.958804] lp0: ECP mode |
182 |
[ 1105.991826] lp0: ECP mode |
183 |
[ 4970.226814] SMB connection re-established (-5) |
184 |
[ 5250.224599] Unable to handle kernel paging request at virtual address 0000000100038000 |
185 |
[ 5250.224635] tsk->{mm,active_mm}->context = 0000000000001f7c |
186 |
[ 5250.224659] tsk->{mm,active_mm}->pgd = fffff800155a2000 |
187 |
[ 5250.224682] \|/ ____ \|/ |
188 |
[ 5250.224693] "@'/ .. \`@" |
189 |
[ 5250.224704] /_| \__/ |_\ |
190 |
[ 5250.224714] \__U_/ |
191 |
[ 5250.224737] madplay(20175): Oops [#1] |
192 |
[ 5250.224765] TSTATE: 0000000080009600 TPC: 0000000000543cd0 TNPC: 0000000000543cd4 Y: 00000000 Not tainted |
193 |
[ 5250.224814] TPC: <memcpy+0x218/0x13c0> |
194 |
[ 5250.224836] g0: 0000000000612fe4 g1: 0000000100039078 g2: 0000000000000000 g3: 0000000000000038 |
195 |
[ 5250.224873] g4: fffff80010430da0 g5: 0000000000000000 g6: fffff80005638000 g7: 0000000000001080 |
196 |
[ 5250.224909] o0: fffff800002b6700 o1: 0000000100038000 o2: 0000000000000008 o3: 0000000000543c40 |
197 |
[ 5250.224946] o4: fffff800002b6080 o5: 0000000000000000 sp: fffff8000563aaf1 ret_pc: 0000000000545928 |
198 |
[ 5250.224978] RPC: <memcpy_user_stub+0x14/0x24> |
199 |
[ 5250.225004] l0: 0000000000000001 l1: fffff80017ad0420 l2: 0000000000000000 l3: 00000000006ff400 |
200 |
[ 5250.225041] l4: fffff80017ad0420 l5: 00000000000019b7 l6: 00000000007b7728 l7: fffff80010430fa0 |
201 |
[ 5250.225077] i0: fffff800002b6080 i1: 00000001000378c0 i2: 00000000000017c0 i3: 000000000027e48e |
202 |
[ 5250.225114] i4: 00000000000005f0 i5: fffff800156a2c00 i6: fffff8000563abb1 i7: 0000000000613078 |
203 |
[ 5250.225152] I7: <snd_pcm_lib_write_transfer+0x9c/0xc8> |
204 |
[ 5250.225172] Caller[0000000000613078]: snd_pcm_lib_write_transfer+0x9c/0xc8 |
205 |
[ 5250.225204] Caller[00000000006133a4]: snd_pcm_lib_write1+0x300/0x43c |
206 |
[ 5250.225235] Caller[0000000010026750]: snd_pcm_oss_sync+0x170/0x27c [snd_pcm_oss] |
207 |
[ 5250.225307] Caller[00000000100271e4]: snd_pcm_oss_release+0x24/0x9c [snd_pcm_oss] |
208 |
[ 5250.225356] Caller[00000000004869f8]: __fput+0xb8/0x178 |
209 |
[ 5250.225394] Caller[0000000000485670]: filp_close+0x70/0x7c |
210 |
[ 5250.225424] Caller[0000000000446a0c]: put_files_struct+0xa8/0xf0 |
211 |
[ 5250.225461] Caller[00000000004471fc]: do_exit+0x200/0x844 |
212 |
[ 5250.225490] Caller[0000000000447900]: do_group_exit+0x88/0x8c |
213 |
[ 5250.225519] Caller[0000000000450ca0]: get_signal_to_deliver+0x320/0x334 |
214 |
[ 5250.225567] Caller[0000000000433f24]: do_signal32+0x40/0xe00 |
215 |
[ 5250.225603] Caller[00000000004207f8]: do_notify_resume+0x4c/0x574 |
216 |
[ 5250.225646] Caller[00000000004053dc]: __handle_signal+0x18/0x34 |
217 |
[ 5250.225683] Caller[00000000f7db3070]: 0xf7db3078 |
218 |
[ 5250.225707] Instruction DUMP: b7b2c90d bbb3490f bfb3c900 <c39a5e00> e3ba1e00 92026040 8ea1e040 02600032 90022040 |
219 |
[ 5250.225774] Fixing recursive fault but reboot is needed! |
220 |
[68491.048413] eth0: Happy Meal out of receive descriptors, packet dropped. |
221 |
[68511.586097] eth0: Happy Meal out of receive descriptors, packet dropped. |
222 |
[69308.765671] usb 1-2: USB disconnect, address 3 |
223 |
[69308.771124] drivers/usb/class/usblp.c: usblp0: removed |
224 |
[69326.897173] usb 1-2: new high speed USB device using ehci_hcd and address 6 |
225 |
[69327.031978] usb 1-2: configuration #1 chosen from 1 choice |
226 |
[69327.032954] scsi3 : SCSI emulation for USB Mass Storage devices |
227 |
[69327.033492] usb-storage: device found at 6 |
228 |
[69327.033510] usb-storage: waiting for device to settle before scanning |
229 |
[69327.035609] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 6 if 1 alt 0 proto 2 vid 0x04B8 pid 0x081E |
230 |
[69332.035228] Vendor: EPSON Model: Stylus Storage Rev: 1.00 |
231 |
[69332.035300] Type: Direct-Access ANSI SCSI revision: 02 |
232 |
[69332.040422] sd 3:0:0:0: Attached scsi removable disk sdb |
233 |
[69332.042608] usb-storage: device scan complete |
234 |
[69594.022714] usb 1-2: USB disconnect, address 6 |
235 |
[69594.893131] drivers/usb/class/usblp.c: usblp0: removed |
236 |
[69705.183927] usb 1-2: new high speed USB device using ehci_hcd and address 7 |
237 |
[69705.318570] usb 1-2: configuration #1 chosen from 1 choice |
238 |
[69705.319513] scsi4 : SCSI emulation for USB Mass Storage devices |
239 |
[69705.320052] usb-storage: device found at 7 |
240 |
[69705.320072] usb-storage: waiting for device to settle before scanning |
241 |
[69705.322301] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 7 if 1 alt 0 proto 2 vid 0x04B8 pid 0x081E |
242 |
[69710.321844] Vendor: EPSON Model: Stylus Storage Rev: 1.00 |
243 |
[69710.321989] Type: Direct-Access ANSI SCSI revision: 02 |
244 |
[69710.327006] sd 4:0:0:0: Attached scsi removable disk sdb |
245 |
[69710.329115] usb-storage: device scan complete |
246 |
[70193.264110] usb 1-2: USB disconnect, address 7 |
247 |
[70194.055131] drivers/usb/class/usblp.c: usblp0: removed |
248 |
[70696.987743] usb 1-2: new high speed USB device using ehci_hcd and address 8 |
249 |
[70697.129249] usb 1-2: configuration #1 chosen from 1 choice |
250 |
[70697.130294] scsi5 : SCSI emulation for USB Mass Storage devices |
251 |
[70697.130813] usb-storage: device found at 8 |
252 |
[70697.130832] usb-storage: waiting for device to settle before scanning |
253 |
[70697.133038] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 8 if 1 alt 0 proto 2 vid 0x04B8 pid 0x081E |
254 |
[70702.130040] Vendor: EPSON Model: Stylus Storage Rev: 1.00 |
255 |
[70702.130110] Type: Direct-Access ANSI SCSI revision: 02 |
256 |
[70702.135597] sd 5:0:0:0: Attached scsi removable disk sdb |
257 |
[70702.137503] usb-storage: device scan complete |