Re: [gentoo-user-es] Cuelgues aleatorios.

[Angel Cervera Claudio]

Os envío el dmesg, por si os es de utilidad.
Gracias de nuevo.

# dmesg
Linux version 2.6.23-gentoo-r6 (root@lastres) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 SMP Mon Jan 28 14:44:32 CET 2008
Command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 udev
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ffd0000 (usable)
 BIOS-e820: 000000007ffd0000 - 000000007ffde000 (ACPI data)
 BIOS-e820: 000000007ffde000 - 0000000080000000 (ACPI NVS)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 524240) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000F7BB0, 0014 (r0 ACPIAM)
ACPI: RSDT 7FFD0000, 0038 (r1 A M I  OEMRSDT   7000627 MSFT       97)
ACPI: FACP 7FFD0200, 0084 (r2 A M I  OEMFACP   7000627 MSFT       97)
ACPI: DSDT 7FFD0460, 7AD4 (r1  A6JC0 A6JC0219      219 INTL  2002026)
ACPI: FACS 7FFDE000, 0040
ACPI: APIC 7FFD0390, 005C (r1 A M I  OEMAPIC   7000627 MSFT       97)
ACPI: MCFG 7FFD03F0, 003C (r1 A M I  OEMMCFG   7000627 MSFT       97)
ACPI: BOOT 7FFD0430, 0028 (r1 A M I  OEMBOOT   7000627 MSFT       97)
ACPI: OEMB 7FFDE040, 0046 (r1 A M I  AMI_OEM   7000627 MSFT       97)
No NUMA configuration found
Faking a node at 0000000000000000-000000007ffd0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 524240) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000007ffd0000
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   524240
On node 0 totalpages: 524143
  DMA zone: 56 pages used for memmap
  DMA zone: 1251 pages reserved
  DMA zone: 2692 pages, LIFO batch:0
  DMA32 zone: 7111 pages used for memmap
  DMA32 zone: 513033 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 34536 bytes of per cpu data
Built 1 zonelists in Node order.  Total pages: 515725
Policy zone: DMA32
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 udev
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1662.522 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Memory: 2060456k/2096960k available (2901k kernel code, 36116k reserved, 1142k data, 332k init)
Calibrating delay using timer specific routine.. 3328.40 BogoMIPS (lpj=6656804)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 10390760
Detected 10.390 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.22 BogoMIPS (lpj=6650456)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU         T5500  @ 1.66GHz stepping 06
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 12)
ACPI: Power Resource [GFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-GART: No AMD northbridge found.
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:09: iomem range 0xffb80000-0xffbfffff could not be reserved
pnp: 00:09: iomem range 0xfff80000-0xffffffff could not be reserved
pnp: 00:0a: iomem range 0xffc00000-0xfff7ffff could not be reserved
pnp: 00:0b: ioport range 0x400-0x41f has been reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0b: iomem range 0xfec10000-0xfec17fff has been reserved
pnp: 00:0b: iomem range 0xfec28000-0xfec2ffff has been reserved
pnp: 00:0c: iomem range 0xe0000000-0xe3ffffff has been reserved
pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0d: iomem range 0xc0000-0xcffff has been reserved
pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: f9f00000-fdffffff
  PREFETCH window: bdf00000-ddefffff
PCI: Bridge: 0000:00:1c.0
  IO window: c000-cfff
  MEM window: fe000000-fe0fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
  IO window: disabled.
  MEM window: fe100000-fe1fffff
  PREFETCH window: disabled.
PCI: Bus 5, cardbus bridge: 0000:04:01.0
  IO window: 0000d000-0000d0ff
  IO window: 0000d400-0000d4ff
  PREFETCH window: 88000000-8bffffff
  MEM window: 8c000000-8fffffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: fe200000-feafffff
  PREFETCH window: ddf00000-dfefffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 17
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2245k freed
Simple Boot Flag at 0x52 set to 0x1
audit: initializing netlink socket (disabled)
audit(1201794721.664:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Linux agpgart interface v0.102
ACPI: AC Adapter [AC0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input3
ACPI: Sleep Button (CM) [SLPB]
ACPI: Transitioning device [FN00] to D3
ACPI: Transitioning device [FN00] to D3
ACPI: Fan [FN00] (off)
input: Video Bus as /class/input/input4
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ACPI Warning (tbutils-0217): Incorrect checksum in table [SSDT] -  83, should be 6F [20070126]
ACPI: SSDT 7FFD7F40, 0CC3 (r1    AMI   CPU1PM        1 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Warning (tbutils-0217): Incorrect checksum in table [SSDT] -  3C, should be 02 [20070126]
ACPI: SSDT 7FFD8C10, 04A4 (r1    AMI   CPU2PM        1 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (68 C)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
asus-laptop: Asus Laptop Support version 0.42
asus-laptop:   A6JC model detected
Registered led device: asus:mail
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HTS541010G9AT00, ATA DISK drive
hdb: MATSHITADVD-RAM UJ-850S, ATAPI CD/DVD-ROM drive
hda: selected mode 0x45
hdb: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 195371568 sectors (100030 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3
hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input5
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 332k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfbc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ec00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input6
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 22, io base 0x0000e480
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-2: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech Optical USB Mouse as /class/input/input7
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
ACPI: PCI Interrupt 0000:04:01.1[B] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18]  MMIO=[feaff800-feafffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
libata version 2.21 loaded.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@××××××.com
JFS: nTxBlock = 8192, nTxLock = 65536
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800036e619e]
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age
30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
input: PC Speaker as /class/input/input8
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xffffc200011d4000, 00:18:f3:83:3e:dc, XID 38000000 IRQ 16
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  100.14.19  Wed Sep 12 14:08:38 PDT 2007
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:04:01.2 [1180:0822] (rev 17)
ACPI: PCI Interrupt 0000:04:01.2[C] -> GSI 19 (level, low) -> IRQ 19
mmc0: SDHCI at 0xfeaff400 irq 19 DMA
Yenta: CardBus bridge found at 0000:04:01.0 [1043:1237]
Yenta: ISA IRQ mask 0x04b8, PCI irq 17
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#04) from #05 to #08
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
pcmcia: parent PCI bridge Memory window: 0xfe200000 - 0xfeafffff
pcmcia: parent PCI bridge Memory window: 0xddf00000 - 0xdfefffff
Adding 522104k swap on /dev/hda2.  Priority:-1 extents:1 across:522104k
r8169: eth0: link up
r8169: eth0: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present


Angel Cervera Claudio escribió:
> Hola a todos.
> He reinstalado mi gentoo x86_64 y de vez en cuando se me queda colgado.
> No consigo averiguar cual puede ser la causa, ya que no parece repetirse la misma casuística.
> En /var/log/messages no aparece nada raro ni mensajes de error.
> Qué podría hacer para buscar la causa del problema?
>
> Un saludo y gracias
>
> Mi emerge:
> # emerge --info
> Portage 2.1.3.19 (default-linux/amd64/2007.0/desktop, gcc-4.1.2, glibc-2.6.1-r0, 2.6.23-gentoo-r6 x86_64)
> =================================================================
> System uname: 2.6.23-gentoo-r6 x86_64 Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz
> Timestamp of tree: Thu, 31 Jan 2008 07:46:01 +0000
> app-shells/bash:     3.2_p17-r1
> dev-java/java-config: 1.3.7, 2.0.33-r1
> dev-lang/python:     2.4.4-r6
> dev-python/pycrypto: 2.0.1-r6
> sys-apps/baselayout: 1.12.10-r5
> sys-apps/sandbox:    1.2.18.1-r2
> sys-devel/autoconf:  2.13, 2.61-r1
> sys-devel/automake:  1.5, 1.7.9-r1, 1.8.5-r3, 1.9.6-r2, 1.10
> sys-devel/binutils:  2.18-r1
> sys-devel/gcc-config: 1.4.0-r4
> sys-devel/libtool:   1.5.24
> virtual/os-headers:  2.6.23-r3
> ACCEPT_KEYWORDS="amd64"
> CBUILD="x86_64-pc-linux-gnu"
> CFLAGS="-march=nocona -O2 -pipe"
> CHOST="x86_64-pc-linux-gnu"
> CONFIG_PROTECT="/etc /usr/share/X11/xkb"
> CONFIG_PROTECT_MASK="/etc/env.d /etc/env.d/java/ /etc/fonts/fonts.conf /etc/gconf /etc/revdep-rebuild /etc/terminfo /etc/udev/rules.d"
> CXXFLAGS="-march=nocona -O2 -pipe"
> DISTDIR="/usr/portage/distfiles"
> FEATURES="distlocks metadata-transfer sfperms strict unmerge-orphans userfetch"
> GENTOO_MIRRORS="http://ftp.uni-erlangen.de/pub/mirrors/gentoo http://mirrors.sec.informatik.tu-darmstadt.de/gentoo/
> http://ftp.udc.es/gentoo/ ftp://ftp.udc.es/gentoo/ "
> LINGUAS="es es-ES"
> MAKEOPTS="-j3"
> PKGDIR="/usr/portage/packages"
> PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times --compress --force --whole-file --delete --delete-after --stats
> --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages --filter=H_**/files/digest-*"
> PORTAGE_TMPDIR="/var/tmp"
> PORTDIR="/usr/portage"
> SYNC="rsync://rsync.europe.gentoo.org/gentoo-portage"
> USE="X acl acpi alsa amd64 avahi bash-completion berkdb bitmap-fonts bluetooth cairo cdr cli cracklib crypt cups dbus dri dvd dvdr
> dvdread eds emboss encode esd evo exif fam ffmpeg firefox flac fontconfig foomaticdb fortran gdbm gif gnome gpm gstreamer gtk
> gtkhtml hal iconv imagemagick ipv6 isdnlog jpeg kerberos ldap mad midi mikmod mmx mp3 mpeg mudflap ncurses nls nptl nptlonly
> nsplugin nvidia ogg opengl openmp oss pam pcre pdf perl png ppds pppd python qt3support quicktime readline reflection sdl session
> spell spl sse sse2 ssl ssse3 svg tcpd tiff tk truetype truetype-fonts type1 type1-fonts unicode vorbis wmf xinerama xml xorg xpm xv
> zlib" ALSA_CARDS="ali5451 als4000 atiixp atiixp-modem bt87x ca0106 cmipci emu10k1x ens1370 ens1371 es1938 es1968 fm801 hda-intel
> intel8x0 intel8x0m maestro3 trident usb-audio via82xx via82xx-modem ymfpci" ALSA_PCM_PLUGINS="adpcm alaw asym copy dmix dshare
> dsnoop empty extplug file hooks iec958 ioplug ladspa lfloat linear meter mulaw multi null plug rate route share shm softvol"
> APACHE2_MODULES="actions alias auth_basic authn_alias authn_anon authn_dbm authn_default authn_file authz_dbm authz_default
> authz_groupfile authz_host authz_owner authz_user autoindex cache dav dav_fs dav_lock deflate dir disk_cache env expires ext_filter
> file_cache filter headers include info log_config logio mem_cache mime mime_magic negotiation rewrite setenvif speling status
> unique_id userdir usertrack vhost_alias" ELIBC="glibc" INPUT_DEVICES="keyboard mouse" KERNEL="linux" LCD_DEVICES="bayrad cfontz
> cfontz633 glk hd44780 lb216 lcdm001 mtxorb ncurses text" LINGUAS="es es-ES" USERLAND="GNU" VIDEO_CARDS="nvidia"
> Unset:  CPPFLAGS, CTARGET, EMERGE_DEFAULT_OPTS, INSTALL_MASK, LANG, LC_ALL, LDFLAGS, PORTAGE_COMPRESS, PORTAGE_COMPRESS_FLAGS,
> PORTAGE_RSYNC_EXTRA_OPTS, PORTDIR_OVERLAY
>
>
-- 
gentoo-user-es@l.g.o mailing list