Re: [gentoo-user] Megaraid or XFS bug in 2.6.20-gentoo-r8?

[Joshua Schmidlkofer]

This is a late reply - but XFS detected what it suspected was underlying
hardware corruption, and it shut down the filesystem in an attempt to
preserve sanity of the filesystem.  This is most likely hardware failure.
Hope you had good luck with it.

On 5/25/07, Jules Colding <colding@×××××.com> wrote:
>
> Hi,
>
> Earlier today I was, as usual, pushing changes from my bk child
> repository to the master repository.
>
> What happened was that the box became totally unresponsive, but it did
> not lock up completely as I was able to ssh into it from another box. A
> quick "top" show that the load was above 22 but going down towards a
> more reasonable level.
>
> The VMware image was dead so I tried to reboot the box in an orderly
> fashin and then recover the VMware session when the box came up again.
>
> Unfortunately this never happened. 3 of my 5 disks in my raid 5 array
> was down. I had to let my raid card check the consistency before it was
> possible to boot. This took a few hours...
>
> The box is now up and running smoothly, but the system log showed that
> something bad had happened with the disks. I can't tell if it is XFS,
> the LSI Logic MegaRAID driver or a hardware problem. The hardware is
> about one year old and has never acted unreasonably.
>
> The child repo is a w2003 virtual VMware guest box hosted on localhost.
> The master is a local repository on localhost. The VMware image is on
> and external SCSI raid 5 array with 5 disks. The disks are all "Seagate
> ST336754LW". The raid card is a "LSI Logic MegaRAID SCSI 320-4x". The
> filesystem is XFS and the device is "/dev/sdb1".
>
> I've appended the relevant log below the "emerge --info" and dmseg
> output.
>
> Sorry for the long mail but thanks,
>   jules
>
>
>
> #################### emerge --info #######################
> omc-2 ~ # emerge --info
> Portage 2.1.2.7 (default-linux/amd64/2007.0, gcc-4.1.2, glibc-2.5-r2,
> 2.6.20-gentoo-r8 x86_64)
> =================================================================
> System uname: 2.6.20-gentoo-r8 x86_64 AMD Opteron(tm) Processor 252
> Gentoo Base System release 1.12.9
> Timestamp of tree: Fri, 25 May 2007 19:20:01 +0000
> dev-java/java-config: 1.3.7, 2.0.31-r5
> dev-lang/python:     2.3.5-r3, 2.4.4-r4
> dev-python/pycrypto: 2.0.1-r5
> sys-apps/sandbox:    1.2.17
> sys-devel/autoconf:  2.13, 2.61
> sys-devel/automake:  1.4_p6, 1.5, 1.6.3, 1.7.9-r1, 1.8.5-r3, 1.9.6-r2,
> 1.10
> sys-devel/binutils:  2.16.1-r3
> sys-devel/gcc-config: 1.3.16
> sys-devel/libtool:   1.5.22
> virtual/os-headers:  2.6.17-r2
> ACCEPT_KEYWORDS="amd64"
> AUTOCLEAN="yes"
> CBUILD="x86_64-pc-linux-gnu"
> CFLAGS="-march=k8 -O2 -pipe"
> CHOST="x86_64-pc-linux-gnu"
> CONFIG_PROTECT="/etc /usr/share/X11/xkb"
> CONFIG_PROTECT_MASK="/etc/env.d /etc/env.d/java/ /etc/gconf
> /etc/java-config/vms/ /etc/revdep-rebuild /etc/terminfo /etc/texmf/web2c"
> CXXFLAGS="-march=k8 -O2 -pipe"
> DISTDIR="/usr/portage/distfiles"
> FEATURES="distlocks metadata-transfer sandbox sfperms strict"
> GENTOO_MIRRORS="http://ftp.belnet.be/mirror/rsync.gentoo.org/gentoo/
> http://mirrors.sec.informatik.tu-darmstadt.de/gentoo/
> http://pandemonium.tiscali.de/pub/gentoo/
> ftp://ftp.snt.utwente.nl/pub/os/linux/gentoo http://mirror.gentoo.no/
> http://gentoo.prz.rzeszow.pl http://ftp.du.se/pub/os/gentoo
> ftp://mirror.pudas.net/gentoo"
> LC_ALL="en_US.utf8"
> MAKEOPTS="-j3"
> PKGDIR="/usr/portage/packages"
> PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times
> --compress --force --whole-file --delete --delete-after --stats
> --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages
> --filter=H_**/files/digest-*"
> PORTAGE_TMPDIR="/var/tmp"
> PORTDIR="/usr/portage"
> PORTDIR_OVERLAY="/usr/local/portage"
> SYNC="rsync://rsync.europe.gentoo.org/gentoo-portage"
> USE="X aac aalib acl alsa amd64 apache2 berkdb bitmap-fonts browserplugin
> bzip2 cdr cli cracklib crypt cups dri dvd dvdr dvdread emacs fam fbcon
> firefox foomaticdb fortran gdbm gnome gpm gtk gtk2 hal iconv ipv6 isdnlog
> jpeg libg++ midi mmx mp3 mudflap ncurses nls nptl nptlonly nsplugin nvidia
> ogg opengl openmp oss pam pcre pdf perl png portaudio pppd python readline
> reflection session spl sse sse2 ssl tcpd tetex theora truetype-fonts
> type1-fonts unicode vorbis wma xine xorg xvid zlib" ALSA_CARDS="emu10k1"
> ALSA_PCM_PLUGINS="adpcm alaw asym copy dmix dshare dsnoop empty extplug file
> hooks iec958 ioplug ladspa lfloat linear meter mulaw multi null plug rate
> route share shm softvol" ELIBC="glibc" INPUT_DEVICES="evdev keyboard mouse"
> KERNEL="linux" LCD_DEVICES="bayrad cfontz cfontz633 glk hd44780 lb216
> lcdm001 mtxorb ncurses text" USERLAND="GNU" VIDEO_CARDS="nv nvidia vesa"
> Unset:  CTARGET, EMERGE_DEFAULT_OPTS, INSTALL_MASK, LANG, LDFLAGS,
> LINGUAS, PORTAGE_COMPRESS, PORTAGE_COMPRESS_FLAGS, PORTAGE_RSYNC_EXTRA_OPTS
>
> ############################ dmesg ############################
> [    0.000000] Linux version 2.6.20-gentoo-r8 (root@omc-2) (gcc version
> 4.1.1 (Gentoo 4.1.1-r3)) #1 SMP Wed May 16 13:59:23 CEST 2007
> [    0.000000] Command line: root=/dev/sda4 vga=0x31B
> video=vesafb:mtrr,ywrap
> [    0.000000] BIOS-provided physical RAM map:
> [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> [    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> [    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> [    0.000000]  BIOS-e820: 0000000000100000 - 00000000ca000000 (usable)
> [    0.000000]  BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
> [    0.000000]  BIOS-e820: 0000000100000000 - 0000000200000000 (usable)
> [    0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
> [    0.000000] Entering add_active_range(0, 256, 827392) 1 entries of 3200
> used
> [    0.000000] Entering add_active_range(0, 1048576, 2097152) 2 entries of
> 3200 used
> [    0.000000] end_pfn_map = 2097152
> [    0.000000] DMI 2.3 present.
> [    0.000000] ACPI: Unable to locate RSDP
> [    0.000000] No NUMA configuration found
> [    0.000000] Faking a node at 0000000000000000-0000000200000000
> [    0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
> [    0.000000] Entering add_active_range(0, 256, 827392) 1 entries of 3200
> used
> [    0.000000] Entering add_active_range(0, 1048576, 2097152) 2 entries of
> 3200 used
> [    0.000000] Bootmem setup node 0 0000000000000000-0000000200000000
> [    0.000000] Zone PFN ranges:
> [    0.000000]   DMA             0 ->     4096
> [    0.000000]   DMA32        4096 ->  1048576
> [    0.000000]   Normal    1048576 ->  2097152
> [    0.000000] early_node_map[3] active PFN ranges
> [    0.000000]     0:        0 ->      159
> [    0.000000]     0:      256 ->   827392
> [    0.000000]     0:  1048576 ->  2097152
> [    0.000000] On node 0 totalpages: 1875871
> [    0.000000]   DMA zone: 56 pages used for memmap
> [    0.000000]   DMA zone: 1351 pages reserved
> [    0.000000]   DMA zone: 2592 pages, LIFO batch:0
> [    0.000000]   DMA32 zone: 14280 pages used for memmap
> [    0.000000]   DMA32 zone: 809016 pages, LIFO batch:31
> [    0.000000]   Normal zone: 14336 pages used for memmap
> [    0.000000]   Normal zone: 1034240 pages, LIFO batch:31
> [    0.000000] Intel MultiProcessor Specification v1.4
> [    0.000000] MPTABLE: OEM ID: TYAN     MPTABLE: Product ID: RHAPSODY
> MPTABLE: APIC at: 0xFEE00000
> [    0.000000] Processor #0 (Bootup-CPU)
> [    0.000000] Processor #1
> [    0.000000] I/O APIC #2 at 0xFEC00000.
> [    0.000000] I/O APIC #3 at 0xFA9FE000.
> [    0.000000] I/O APIC #4 at 0xFA9FF000.
> [    0.000000] Setting APIC routing to flat
> [    0.000000] Processors: 2
> [    0.000000] Nosave address range: 000000000009f000 - 00000000000a0000
> [    0.000000] Nosave address range: 00000000000a0000 - 00000000000e0000
> [    0.000000] Nosave address range: 00000000000e0000 - 0000000000100000
> [    0.000000] Nosave address range: 00000000ca000000 - 00000000ff780000
> [    0.000000] Nosave address range: 00000000ff780000 - 0000000100000000
> [    0.000000] Allocating PCI resources starting at cc000000 (gap:
> ca000000:35780000)
> [    0.000000] PERCPU: Allocating 32384 bytes of per cpu data
> [    0.000000] Built 1 zonelists.  Total pages: 1845848
> [    0.000000] Kernel command line: root=/dev/sda4 vga=0x31B
> video=vesafb:mtrr,ywrap
> [    0.000000] Initializing CPU#0
> [    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
> [   72.475397] Console: colour dummy device 80x25
> [   72.479079] Dentry cache hash table entries: 1048576 (order: 11,
> 8388608 bytes)
> [   72.484875] Inode-cache hash table entries: 524288 (order: 10, 4194304
> bytes)
> [   72.486803] Checking aperture...
> [   72.486810] CPU 0: aperture @ f0000000 size 128 MB
> [   72.486814] CPU 1: aperture @ f0000000 size 128 MB
> [   72.562934] Memory: 7370788k/8388608k available (3373k kernel code,
> 132696k reserved, 1220k data, 332k init)
> [   72.641234] Calibrating delay using timer specific routine.. 5190.87BogoMIPS (lpj=10381746)
> [   72.641300] Mount-cache hash table entries: 256
> [   72.641399] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
> bytes/line)
> [   72.641403] CPU: L2 Cache: 1024K (64 bytes/line)
> [   72.641406] CPU 0/0 -> Node 0
> [   72.641419] Freeing SMP alternatives: 32k freed
> [   72.681984] Using local APIC timer interrupts.
> [   72.720561] result 12452622
> [   72.720563] Detected 12.452 MHz APIC timer.
> [   72.721330] Booting processor 1/2 APIC 0x1
> [   72.731626] Initializing CPU#1
> [   72.809090] Calibrating delay using timer specific routine.. 5180.67BogoMIPS (lpj=10361356)
> [   72.809096] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
> bytes/line)
> [   72.809098] CPU: L2 Cache: 1024K (64 bytes/line)
> [   72.809101] CPU 1/1 -> Node 0
> [   72.809209] AMD Opteron(tm) Processor 252 stepping 01
> [   72.813099] CPU 1: Syncing TSC to CPU 0.
> [   72.813240] CPU 1: synchronized TSC with CPU 0 (last diff 152 cycles,
> maxerr 649 cycles)
> [   72.813248] Brought up 2 CPUs
> [   72.813347] testing NMI watchdog ... OK.
> [   72.853401] time.c: Using 1.193182 MHz WALL PIT GTOD PIT/TSC timer.
> [   72.853403] time.c: Detected 2590.142 MHz processor.
> [   72.872857] migration_cost=306
> [   72.873157] NET: Registered protocol family 16
> [   72.873238] PCI: Using configuration type 1
> [   72.874079] ACPI: Interpreter disabled.
> [   72.874200] SCSI subsystem initialized
> [   72.874247] usbcore: registered new interface driver usbfs
> [   72.874270] usbcore: registered new interface driver hub
> [   72.874297] usbcore: registered new device driver usb
> [   72.874323] PCI: Probing PCI hardware
> [   72.874327] PCI: Probing PCI hardware (bus 00)
> [   72.876042] Boot video device is 0000:06:00.0
> [   72.876088] PCI: Discovered primary peer bus 06 [IRQ]
> [   72.876093] PCI: Using IRQ router default [1022/746b] at 0000:00:07.3
> [   72.876103] PCI->APIC IRQ transform: 0000:00:07.2[D] -> IRQ 19
> [   72.876112] PCI->APIC IRQ transform: 0000:04:00.0[D] -> IRQ 19
> [   72.876115] PCI->APIC IRQ transform: 0000:04:00.1[D] -> IRQ 19
> [   72.876119] PCI->APIC IRQ transform: 0000:04:0a.0[A] -> IRQ 16
> [   72.876124] PCI->APIC IRQ transform: 0000:04:0a.2[B] -> IRQ 17
> [   72.876127] PCI->APIC IRQ transform: 0000:03:09.0[A] -> IRQ 24
> [   72.876132] PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 29
> [   72.876135] PCI->APIC IRQ transform: 0000:06:00.0[A] -> IRQ 16
> [   72.876220] PCI-DMA: Disabling AGP.
> [   72.876295] PCI-DMA: aperture base @ f0000000 size 131072 KB
> [   72.876298] PCI-DMA: using GART IOMMU.
> [   72.876302] PCI-DMA: Reserving 128MB of IOMMU area in the AGP aperture
> [   72.876567] PCI: Bridge: 0000:00:06.0
> [   72.876571]   IO window: b000-bfff
> [   72.876576]   MEM window: fa800000-fa8fffff
> [   72.876580]   PREFETCH window: disabled.
> [   72.876585] PCI: Bridge: 0000:00:0a.0
> [   72.876586]   IO window: disabled.
> [   72.876590]   MEM window: fa700000-fa7fffff
> [   72.876593]   PREFETCH window: ca200000-ca2fffff
> [   72.876596] PCI: Bridge: 0000:01:06.0
> [   72.876598]   IO window: disabled.
> [   72.876601]   MEM window: fa500000-fa6fffff
> [   72.876605]   PREFETCH window: ca100000-ca1fffff
> [   72.876608] PCI: Bridge: 0000:00:0b.0
> [   72.876610]   IO window: disabled.
> [   72.876613]   MEM window: fa500000-fa6fffff
> [   72.876616]   PREFETCH window: ca100000-ca1fffff
> [   72.876680] NET: Registered protocol family 2
> [   72.909049] IP route cache hash table entries: 262144 (order: 9,
> 2097152 bytes)
> [   72.910349] TCP established hash table entries: 262144 (order: 10,
> 4194304 bytes)
> [   72.912992] TCP bind hash table entries: 65536 (order: 8, 1048576
> bytes)
> [   72.913713] TCP: Hash tables configured (established 262144 bind 65536)
> [   72.913717] TCP reno registered
> [   72.925808] Total HugeTLB memory allocated, 0
> [   72.926016] SGI XFS with large block/inode numbers, no debug enabled
> [   72.926186] io scheduler noop registered
> [   72.926189] io scheduler anticipatory registered (default)
> [   72.926201] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for
> 0000:00:0a.0 subordinate bus.
> [   72.926206] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for
> 0000:00:0b.0 subordinate bus.
> [   72.988079] Real Time Clock Driver v1.12ac
> [   72.988088] Linux agpgart interface v0.101 (c) Dave Jones
> [   72.988195] vesafb: framebuffer at 0xd0000000, mapped to
> 0xffffc20000000000, using 10240k, total 262144k
> [   72.988200] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
> [   72.988202] vesafb: scrolling: redraw
> [   72.988205] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
> [   73.582014] Console: switching to colour frame buffer device 160x64
> [   74.180002] fb0: VESA VGA frame buffer device
> [   74.182902] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
> sharing disabled
> [   74.188264] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [   74.188577] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> [   74.188877] Floppy drive(s): fd0 is 1.44M
> [   74.219762] FDC 0 is a post-1991 82077
> [   74.223408] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024
> blocksize
> [   74.228074] loop: loaded (max 8 devices)
> [   74.230484] tg3.c:v3.72 (January 8, 2007)
> [   74.259489] eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)]
> (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:2f:8a:1c
> [   74.267224] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0]
> WireSpeed[1] TSOcap[1]
> [   74.272244] eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
> [   74.275437] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> [   74.279252] ide: Assuming 33MHz system bus speed for PIO modes;
> override with idebus=xx
> [   74.284087] AMD8111: IDE controller at PCI slot 0000:00:07.1
> [   74.287480] AMD8111: chipset revision 3
> [   74.289783] AMD8111: not 100% native mode: will probe irqs later
> [   74.293392] AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
> [   74.296844]     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA,
> hdb:DMA
> [   74.301394] Probing IDE interface ide0...
> [   74.591686] hda: Maxtor 6Y120P0, ATA DISK drive
> [   75.043245] hdb: _NEC DVD_RW ND-3520A, ATAPI CD/DVD-ROM drive
> [   75.103631] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> [   75.106536] Probing IDE interface ide1...
> [   75.670596] hda: max request size: 128KiB
> [   75.673565] hda: 240121728 sectors (122942 MB) w/7936KiB Cache,
> CHS=65535/16/63<6>hda: hw_config=403b
> [   75.680069] , UDMA(133)
> [   75.681947] hda: cache flushes supported
> [   75.684596]  hda: hda1
> [   75.691357] hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache,
> UDMA(33)
> [   75.697102] Uniform CD-ROM driver Revision: 3.20
> [   75.701665] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03
> EST 2006)
> [   75.706536] megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST
> 2006)
> [   75.711221] megaraid: probe new device 0x1000:0x0407:0x1000:0x0531: bus
> 2:slot 0:func 0
> [   75.734551] megaraid: fw version:[413B] bios version:[H409]
> [   75.738644] scsi0 : LSI Logic MegaRAID driver
> [   75.741606] scsi[0]: scanning scsi channel 0 [Phy 0] for non-raid
> devices
> [   78.497750] scsi[0]: scanning scsi channel 1 [Phy 1] for non-raid
> devices
> [   81.033700] scsi[0]: scanning scsi channel 2 [Phy 2] for non-raid
> devices
> [   84.787253] scsi[0]: scanning scsi channel 3 [Phy 3] for non-raid
> devices
> [   88.540752] scsi[0]: scanning scsi channel 4 [virtual] for logical
> drives
> [   88.673881] scsi 0:4:0:0: Direct-Access     MegaRAID LD 0 RAID5  210G
> 413B PQ: 0 ANSI: 2
> [   88.811985] scsi 0:4:1:0: Direct-Access     MegaRAID LD 1 RAID5  139G
> 413B PQ: 0 ANSI: 2
> [   88.952484] SCSI device sda: 430098432 512-byte hdwr sectors (220210
> MB)
> [   89.094379] sda: Write Protect is off
> [   89.237761] sda: Mode Sense: 00 00 00 00
> [   89.237826] sda: asking for cache data failed
> [   89.383379] sda: assuming drive cache: write through
> [   89.531549] SCSI device sda: 430098432 512-byte hdwr sectors (220210
> MB)
> [   89.684225] sda: Write Protect is off
> [   89.838341] sda: Mode Sense: 00 00 00 00
> [   89.838405] sda: asking for cache data failed
> [   89.994374] sda: assuming drive cache: write through
> [   90.153129]  sda: sda1 sda2 sda3 sda4
> [   90.314524] sd 0:4:0:0: Attached scsi disk sda
> [   90.477578] SCSI device sdb: 286711808 512-byte hdwr sectors (146796
> MB)
> [   90.645235] sdb: Write Protect is off
> [   90.814662] sdb: Mode Sense: 00 00 00 00
> [   90.814726] sdb: asking for cache data failed
> [   90.986349] sdb: assuming drive cache: write through
> [   91.160574] SCSI device sdb: 286711808 512-byte hdwr sectors (146796
> MB)
> [   91.339343] sdb: Write Protect is off
> [   91.519545] sdb: Mode Sense: 00 00 00 00
> [   91.519608] sdb: asking for cache data failed
> [   91.701958] sdb: assuming drive cache: write through
> [   91.886738]  sdb: sdb1
> [   92.086112] sd 0:4:1:0: Attached scsi disk sdb
> [   92.274839] has_svm: svm not available
> [   92.274840] kvm: no hardware support
> [   92.465190] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
> (OHCI) Driver (PCI)
> [   92.465297] ohci_hcd 0000:04:00.0: OHCI Host Controller
> [   92.656093] ohci_hcd 0000:04:00.0: new USB bus registered, assigned bus
> number 1
> [   92.847546] ohci_hcd 0000:04:00.0: irq 19, io mem 0xfa8fc000
> [   93.097355] usb usb1: configuration #1 chosen from 1 choice
> [   93.285754] hub 1-0:1.0: USB hub found
> [   93.475178] hub 1-0:1.0: 3 ports detected
> [   93.766720] ohci_hcd 0000:04:00.1: OHCI Host Controller
> [   93.956254] ohci_hcd 0000:04:00.1: new USB bus registered, assigned bus
> number 2
> [   94.146257] ohci_hcd 0000:04:00.1: irq 19, io mem 0xfa8fd000
> [   94.392174] usb usb2: configuration #1 chosen from 1 choice
> [   94.580748] hub 2-0:1.0: USB hub found
> [   94.764097] hub 2-0:1.0: 3 ports detected
> [   95.049580] Initializing USB Mass Storage driver...
> [   95.453144] usb 2-3: new low speed USB device using ohci_hcd and
> address 2
> [   95.791737] usb 2-3: configuration #1 chosen from 1 choice
> [   95.969580] usbcore: registered new interface driver usb-storage
> [   96.144838] USB Mass Storage support registered.
> [   96.331198] input: Logitech USB Receiver as /class/input/input0
> [   96.508054] input: USB HID v1.11 Mouse [Logitech USB Receiver] on
> usb-0000:04:00.1-3
> [   96.687803] usbcore: registered new interface driver usbhid
> [   96.866331] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> [   97.046768] serio: i8042 KBD port at 0x60,0x64 irq 1
> [   97.224607] serio: i8042 AUX port at 0x60,0x64 irq 12
> [   97.400305] mice: PS/2 mouse device common for all mice
> [   97.576465] Advanced Linux Sound Architecture Driver Version 1.0.14rc1(Tue Jan 09 09:56:17 2007 UTC).
> [   97.760904] Installing spdif_bug patch: Audigy 2 ZS [SB0350]
> [   97.949676] input: AT Translated Set 2 keyboard as /class/input/input1
> [   98.111897] ALSA device list:
> [   98.290473]   #0: Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) at
> 0xb800, irq 16
> [   98.472515] TCP bic registered
> [   98.651740] TCP cubic registered
> [   98.828468] TCP westwood registered
> [   99.003403] TCP htcp registered
> [   99.175735] NET: Registered protocol family 1
> [   99.347429] NET: Registered protocol family 17
> [   99.516685] NET: Registered protocol family 15
> [   99.698885] ReiserFS: sda4: found reiserfs format "3.6" with standard
> journal
> [   99.870347] ReiserFS: sda4: using ordered data mode
> [  100.044561] ReiserFS: sda4: journal params: device sda4, size 8192,
> journal first block 18, max trans len 1024, max batch 900, max commit age
> 30, max trans age 30
> [  100.411682] ReiserFS: sda4: checking transaction log (sda4)
> [  100.636903] ReiserFS: sda4: Using r5 hash to sort names
> [  100.821776] VFS: Mounted root (reiserfs filesystem) readonly.
> [  101.006065] Freeing unused kernel memory: 332k freed
> [  106.195023] nvidia: module license 'NVIDIA' taints kernel.
> [  106.199832] NVRM: loading NVIDIA Linux x86_64 Kernel Module  1.0-8776  Mon
> Oct 16 21:53:43 PDT 2006
> [  117.596625] kjournald starting.  Commit interval 5 seconds
> [  117.604901] EXT3 FS on sda1, internal journal
> [  117.604908] EXT3-fs: mounted filesystem with ordered data mode.
> [  117.625471] ReiserFS: sda2: found reiserfs format "3.6" with standard
> journal
> [  117.625482] ReiserFS: sda2: using ordered data mode
> [  117.627327] ReiserFS: sda2: journal params: device sda2, size 8192,
> journal first block 18, max trans len 1024, max batch 900, max commit age
> 30, max trans age 30
> [  117.628128] ReiserFS: sda2: checking transaction log (sda2)
> [  117.659938] ReiserFS: sda2: Using r5 hash to sort names
> [  117.718214] XFS mounting filesystem sdb1
> [  117.813532] Ending clean XFS mount for filesystem: sdb1
> [  118.552329] Adding 1004052k swap on /dev/sda3.  Priority:-1 extents:1
> across:1004052k
> [  129.801479] PM: Writing back config space on device 0000:03:09.0 at
> offset b (was 164714e4, writing 288510f1)
> [  129.801490] PM: Writing back config space on device 0000:03:09.0 at
> offset 3 (was 4000, writing 4010)
> [  129.801495] PM: Writing back config space on device 0000:03:09.0 at
> offset 2 (was 2000000, writing 2000002)
> [  129.801499] PM: Writing back config space on device 0000:03:09.0 at
> offset 1 (was 2b00000, writing 2b00106)
> [  129.801504] PM: Writing back config space on device 0000:03:09.0 at
> offset 0 (was 164714e4, writing 16a714e4)
> [  133.044742] tg3: eth0: Link is up at 1000 Mbps, full duplex.
> [  133.044746] tg3: eth0: Flow control is on for TX and on for RX.
> [  137.375696] vmmon: no version for "struct_module" found: kernel
> tainted.
> [  137.375703] vmmon: no version magic, tainting kernel.
> [  137.376351] /dev/vmmon[5345]: Module vmmon: registered with major=10
> minor=165
> [  137.376405] /dev/vmmon[5345]: Module vmmon: initialized
> [  137.534575] vmnet: no version magic, tainting kernel.
> [  137.773329] /dev/vmnet: open called by PID 5381 (vmnet-bridge)
> [  137.773426] /dev/vmnet: hub 0 does not exist, allocating memory.
> [  137.773504] /dev/vmnet: port on hub 0 successfully opened
> [  137.773543] bridge-eth0: enabling the bridge
> [  137.773575] bridge-eth0: up
> [  137.773603] bridge-eth0: already up
> [  137.773632] bridge-eth0: attached
>
> ##################### /var/log/messages #######################
> May 25 13:01:03 omc-2 [767512.128964] megaraid: aborting-49554524 cmd=2a
> <c=4 t=1 l=0>
> May 25 13:01:03 omc-2 [767512.128973] megaraid abort:
> 49554524:85[255:129], fw owner
> May 25 13:01:03 omc-2 [767512.128981] megaraid: 1 outstanding commands.
> Max wait 300 sec
> May 25 13:01:03 omc-2 [767512.128985] megaraid mbox: Wait for 1 commands
> to complete:300
> May 25 13:01:08 omc-2 [767517.143637] megaraid mbox: Wait for 1 commands
> to complete:295
> May 25 13:01:13 omc-2 [767522.162314] megaraid mbox: Wait for 1 commands
> to complete:290
> May 25 13:01:18 omc-2 [767527.176984] megaraid mbox: Wait for 1 commands
> to complete:285
> May 25 13:01:23 omc-2 [767532.191660] megaraid mbox: Wait for 1 commands
> to complete:280
> May 25 13:01:28 omc-2 [767537.206339] megaraid mbox: Wait for 1 commands
> to complete:275
> May 25 13:01:33 omc-2 [767542.225017] megaraid mbox: Wait for 1 commands
> to complete:270
> May 25 13:01:38 omc-2 [767547.239687] megaraid mbox: Wait for 1 commands
> to complete:265
> May 25 13:01:43 omc-2 [767552.254399] megaraid mbox: Wait for 1 commands
> to complete:260
> May 25 13:01:48 omc-2 [767557.269041] megaraid mbox: Wait for 1 commands
> to complete:255
> May 25 13:01:53 omc-2 [767562.283719] megaraid mbox: Wait for 1 commands
> to complete:250
> May 25 13:01:58 omc-2 [767567.302385] megaraid mbox: Wait for 1 commands
> to complete:245
> May 25 13:02:03 omc-2 [767572.317057] megaraid mbox: Wait for 1 commands
> to complete:240
> May 25 13:02:08 omc-2 [767577.331727] megaraid mbox: Wait for 1 commands
> to complete:235
> May 25 13:02:13 omc-2 [767582.346403] megaraid mbox: Wait for 1 commands
> to complete:230
> May 25 13:02:19 omc-2 [767587.365074] megaraid mbox: Wait for 1 commands
> to complete:225
> May 25 13:02:24 omc-2 [767592.379752] megaraid mbox: Wait for 1 commands
> to complete:220
> May 25 13:02:29 omc-2 [767597.394424] megaraid mbox: Wait for 1 commands
> to complete:215
> May 25 13:02:34 omc-2 [767602.409101] megaraid mbox: Wait for 1 commands
> to complete:210
> May 25 13:02:39 omc-2 [767607.423775] megaraid mbox: Wait for 1 commands
> to complete:205
> May 25 13:02:44 omc-2 [767612.438450] megaraid mbox: Wait for 1 commands
> to complete:200
> May 25 13:02:49 omc-2 [767617.453126] megaraid mbox: Wait for 1 commands
> to complete:195
> May 25 13:02:54 omc-2 [767622.467800] megaraid mbox: Wait for 1 commands
> to complete:190
> May 25 13:02:59 omc-2 [767627.482476] megaraid mbox: Wait for 1 commands
> to complete:185
> May 25 13:03:04 omc-2 [767632.501146] megaraid mbox: Wait for 1 commands
> to complete:180
> May 25 13:03:09 omc-2 [767637.515821] megaraid mbox: Wait for 1 commands
> to complete:175
> May 25 13:03:14 omc-2 [767642.530497] megaraid mbox: Wait for 1 commands
> to complete:170
> May 25 13:03:19 omc-2 [767647.545172] megaraid mbox: Wait for 1 commands
> to complete:165
> May 25 13:03:24 omc-2 [767652.563843] megaraid mbox: Wait for 1 commands
> to complete:160
> May 25 13:04:03 omc-2 [767657.578518] megaraid mbox: Wait for 1 commands
> to complete:155
> May 25 13:04:03 omc-2 [767662.593192] megaraid mbox: Wait for 1 commands
> to complete:150
> May 25 13:04:03 omc-2 [767667.607869] megaraid mbox: Wait for 1 commands
> to complete:145
> May 25 13:04:03 omc-2 [767672.626539] megaraid mbox: Wait for 1 commands
> to complete:140
> May 25 13:04:03 omc-2 [767677.641214] megaraid mbox: Wait for 1 commands
> to complete:135
> May 25 13:04:03 omc-2 [767682.655896] megaraid mbox: Wait for 1 commands
> to complete:130
> May 25 13:04:03 omc-2 [767687.674560] megaraid mbox: Wait for 0 commands
> to complete:125
> May 25 13:04:03 omc-2 [767687.674565] megaraid mbox: reset sequence
> completed sucessfully
> May 25 13:04:03 omc-2 [767687.684016] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684018] end_request: I/O error, dev sdb,
> sector 143460946
> May 25 13:04:03 omc-2 [767687.684048] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0a13       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.684053] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684106] Filesystem "sdb1": Log I/O Error
> Detected.  Shutting down filesystem: sdb1
> May 25 13:04:03 omc-2 [767687.684109] Please umount the filesystem, and
> rectify the problem(s)
> May 25 13:04:03 omc-2 [767687.684115] xfs_force_shutdown(sdb1,0x2) called
> from line 730 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff8039b689
> May 25 13:04:03 omc-2 [767687.684261] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684263] end_request: I/O error, dev sdb,
> sector 49649471
> May 25 13:04:03 omc-2 [767687.684274] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684275] end_request: I/O error, dev sdb,
> sector 50712559
> May 25 13:04:03 omc-2 [767687.684289] Buffer I/O error on device sdb1,
> logical block 6206176
> May 25 13:04:03 omc-2 [767687.684291] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684296] Buffer I/O error on device sdb1,
> logical block 6339062
> May 25 13:04:03 omc-2 [767687.684298] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684302] Buffer I/O error on device sdb1,
> logical block 6339063
> May 25 13:04:03 omc-2 [767687.684303] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684307] Buffer I/O error on device sdb1,
> logical block 6339064
> May 25 13:03:26 omc-2 sshd[30048]: Accepted keyboard-interactive/pam for
> colding from 192.168.0.6 port 56229 ssh2
> May 25 13:04:03 omc-2 [767687.684308] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684321] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684323] end_request: I/O error, dev sdb,
> sector 143461010
> May 25 13:04:03 omc-2 [767687.684345] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0a53       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.684348] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684371] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684373] end_request: I/O error, dev sdb,
> sector 49653607
> May 25 13:04:03 omc-2 [767687.684382] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684384] end_request: I/O error, dev sdb,
> sector 50712583
> May 25 13:04:03 omc-2 [767687.684396] Buffer I/O error on device sdb1,
> logical block 6206693
> May 25 13:04:03 omc-2 [767687.684398] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684402] Buffer I/O error on device sdb1,
> logical block 6339065
> May 25 13:04:03 omc-2 [767687.684403] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684407] Buffer I/O error on device sdb1,
> logical block 6339066
> May 25 13:04:03 omc-2 [767687.684408] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684412] Buffer I/O error on device sdb1,
> logical block 6339067
> May 25 13:04:03 omc-2 [767687.684418] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684420] end_request: I/O error, dev sdb,
> sector 143461074
> May 25 13:04:03 omc-2 [767687.684450] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684455] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0a93       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.684459] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684469] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684471] end_request: I/O error, dev sdb,
> sector 49654071
> May 25 13:04:03 omc-2 [767687.684479] Buffer I/O error on device sdb1,
> logical block 6206751
> May 25 13:04:03 omc-2 [767687.684480] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684495] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:03:26 omc-2 sshd(pam_unix)[30054]: session opened for user
> colding by (uid=0)
> May 25 13:04:03 omc-2 [767687.684497] end_request: I/O error, dev sdb,
> sector 50712607
> May 25 13:04:03 omc-2 [767687.684507] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684508] end_request: I/O error, dev sdb,
> sector 71528687
> May 25 13:04:03 omc-2 [767687.684517] Buffer I/O error on device sdb1,
> logical block 6339068
> May 25 13:04:03 omc-2 [767687.684518] lost page write due to I/O error on
> sdb1
> May 25 13:04:03 omc-2 [767687.684546] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684548] end_request: I/O error, dev sdb,
> sector 143461138
> May 25 13:04:03 omc-2 [767687.684603] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684604] end_request: I/O error, dev sdb,
> sector 49660391
> May 25 13:04:03 omc-2 [767687.684613] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684615] end_request: I/O error, dev sdb,
> sector 50712631
> May 25 13:04:03 omc-2 [767687.684643] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0ad3       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.684651] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684652] end_request: I/O error, dev sdb,
> sector 143461202
> May 25 13:04:03 omc-2 [767687.684672] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684676] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0b13       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.684679] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684701] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684703] end_request: I/O error, dev sdb,
> sector 49670759
> May 25 13:04:03 omc-2 [767687.684711] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684713] end_request: I/O error, dev sdb,
> sector 50712655
> May 25 13:04:03 omc-2 [767687.684749] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684751] end_request: I/O error, dev sdb,
> sector 143461266
> May 25 13:04:03 omc-2 [767687.684784] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0b53       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:03:46 omc-2 sshd[30055]: Accepted keyboard-interactive/pam for
> colding from 192.168.0.6 port 56230 ssh2
> May 25 13:04:03 omc-2 [767687.684787] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684803] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684804] end_request: I/O error, dev sdb,
> sector 49671311
> May 25 13:04:03 omc-2 [767687.684813] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684815] end_request: I/O error, dev sdb,
> sector 50712679
> May 25 13:04:03 omc-2 [767687.684835] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684837] end_request: I/O error, dev sdb,
> sector 50712759
> May 25 13:04:03 omc-2 [767687.684869] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684871] end_request: I/O error, dev sdb,
> sector 143461330
> May 25 13:04:03 omc-2 [767687.684903] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0b93       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.684907] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.684921] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684923] end_request: I/O error, dev sdb,
> sector 49671943
> May 25 13:04:03 omc-2 [767687.684946] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684948] end_request: I/O error, dev sdb,
> sector 50712727
> May 25 13:04:03 omc-2 [767687.684958] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684960] end_request: I/O error, dev sdb,
> sector 50712767
> May 25 13:04:03 omc-2 [767687.684997] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.684999] end_request: I/O error, dev sdb,
> sector 143461394
> May 25 13:04:03 omc-2 [767687.685989] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x88d0bd3       ("xlog_iodone") error 5 buf count
> 32768
> May 25 13:04:03 omc-2 [767687.685993] xfs_force_shutdown(sdb1,0x2) called
> from line 960 of file fs/xfs/xfs_log.c.  Return address = 0xffffffff80398b06
> May 25 13:04:03 omc-2 [767687.686002] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686004] end_request: I/O error, dev sdb,
> sector 49092751
> May 25 13:04:03 omc-2 [767687.686068] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686070] end_request: I/O error, dev sdb,
> sector 49098783
> May 25 13:03:46 omc-2 sshd(pam_unix)[30061]: session opened for user
> colding by (uid=0)
> May 25 13:04:03 omc-2 [767687.686087] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686089] end_request: I/O error, dev sdb,
> sector 49154783
> May 25 13:04:03 omc-2 [767687.686115] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686117] end_request: I/O error, dev sdb,
> sector 49170783
> May 25 13:04:03 omc-2 [767687.686152] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686154] end_request: I/O error, dev sdb,
> sector 49180591
> May 25 13:04:03 omc-2 [767687.686164] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686166] end_request: I/O error, dev sdb,
> sector 49184471
> May 25 13:04:03 omc-2 [767687.686179] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686181] end_request: I/O error, dev sdb,
> sector 49188791
> May 25 13:04:03 omc-2 [767687.686207] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686209] end_request: I/O error, dev sdb,
> sector 49196879
> May 25 13:04:03 omc-2 [767687.686244] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686245] end_request: I/O error, dev sdb,
> sector 49197919
> May 25 13:04:03 omc-2 [767687.686255] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686257] end_request: I/O error, dev sdb,
> sector 49201791
> May 25 13:04:03 omc-2 [767687.686271] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686273] end_request: I/O error, dev sdb,
> sector 49206887
> May 25 13:04:03 omc-2 [767687.686300] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686302] end_request: I/O error, dev sdb,
> sector 49211063
> May 25 13:04:03 omc-2 [767687.686337] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686339] end_request: I/O error, dev sdb,
> sector 49211671
> May 25 13:04:03 omc-2 [767687.686350] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686352] end_request: I/O error, dev sdb,
> sector 49277735
> May 25 13:04:03 omc-2 [767687.686385] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686387] end_request: I/O error, dev sdb,
> sector 49278039
> May 25 13:04:03 omc-2 [767687.686397] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686399] end_request: I/O error, dev sdb,
> sector 49480935
> May 25 13:04:03 omc-2 [767687.686412] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686414] end_request: I/O error, dev sdb,
> sector 49536415
> May 25 13:04:03 omc-2 [767687.686445] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686447] end_request: I/O error, dev sdb,
> sector 49540751
> May 25 13:04:03 omc-2 [767687.686483] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686485] end_request: I/O error, dev sdb,
> sector 49547087
> May 25 13:04:03 omc-2 [767687.686495] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686497] end_request: I/O error, dev sdb,
> sector 49553631
> May 25 13:04:03 omc-2 [767687.686516] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686518] end_request: I/O error, dev sdb,
> sector 49559671
> May 25 13:04:03 omc-2 [767687.686553] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686555] end_request: I/O error, dev sdb,
> sector 49562727
> May 25 13:04:03 omc-2 [767687.686580] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686582] end_request: I/O error, dev sdb,
> sector 49564375
> May 25 13:04:03 omc-2 [767687.686610] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686612] end_request: I/O error, dev sdb,
> sector 49566159
> May 25 13:04:03 omc-2 [767687.686648] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686650] end_request: I/O error, dev sdb,
> sector 49567407
> May 25 13:04:03 omc-2 [767687.686661] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686666] end_request: I/O error, dev sdb,
> sector 49569287
> May 25 13:04:03 omc-2 [767687.686675] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686677] end_request: I/O error, dev sdb,
> sector 49570423
> May 25 13:04:03 omc-2 [767687.686704] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686706] end_request: I/O error, dev sdb,
> sector 49572583
> May 25 13:04:03 omc-2 [767687.686739] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686741] end_request: I/O error, dev sdb,
> sector 49573615
> May 25 13:04:03 omc-2 [767687.686755] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686757] end_request: I/O error, dev sdb,
> sector 49575495
> May 25 13:04:03 omc-2 [767687.686790] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686792] end_request: I/O error, dev sdb,
> sector 49577759
> May 25 13:04:03 omc-2 [767687.686802] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686807] end_request: I/O error, dev sdb,
> sector 49579895
> May 25 13:04:03 omc-2 [767687.686815] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686816] end_request: I/O error, dev sdb,
> sector 49581975
> May 25 13:04:03 omc-2 [767687.686844] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686846] end_request: I/O error, dev sdb,
> sector 49584079
> May 25 13:04:03 omc-2 [767687.686881] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686883] end_request: I/O error, dev sdb,
> sector 49586143
> May 25 13:04:03 omc-2 [767687.686892] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686894] end_request: I/O error, dev sdb,
> sector 49588295
> May 25 13:04:03 omc-2 [767687.686931] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686933] end_request: I/O error, dev sdb,
> sector 49632591
> May 25 13:04:03 omc-2 [767687.686945] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686952] end_request: I/O error, dev sdb,
> sector 49634311
> May 25 13:04:03 omc-2 [767687.686958] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686960] end_request: I/O error, dev sdb,
> sector 49635399
> May 25 13:04:03 omc-2 [767687.686989] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.686991] end_request: I/O error, dev sdb,
> sector 49636711
> May 25 13:04:03 omc-2 [767687.687030] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687032] end_request: I/O error, dev sdb,
> sector 49637855
> May 25 13:04:03 omc-2 [767687.687042] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687049] end_request: I/O error, dev sdb,
> sector 49638983
> May 25 13:04:03 omc-2 [767687.687057] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687059] end_request: I/O error, dev sdb,
> sector 49640151
> May 25 13:04:03 omc-2 [767687.687086] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687087] end_request: I/O error, dev sdb,
> sector 49641687
> May 25 13:04:03 omc-2 [767687.687114] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687115] end_request: I/O error, dev sdb,
> sector 49643471
> May 25 13:04:03 omc-2 [767687.687150] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687152] end_request: I/O error, dev sdb,
> sector 49644279
> May 25 13:04:03 omc-2 [767687.687162] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687163] end_request: I/O error, dev sdb,
> sector 49644975
> May 25 13:04:03 omc-2 [767687.687187] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687188] end_request: I/O error, dev sdb,
> sector 49646287
> May 25 13:04:03 omc-2 [767687.687223] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687225] end_request: I/O error, dev sdb,
> sector 49673415
> May 25 13:04:03 omc-2 [767687.687234] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687236] end_request: I/O error, dev sdb,
> sector 50333919
> May 25 13:04:03 omc-2 [767687.687260] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687262] end_request: I/O error, dev sdb,
> sector 50345087
> May 25 13:04:03 omc-2 [767687.687295] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687297] end_request: I/O error, dev sdb,
> sector 50363479
> May 25 13:04:03 omc-2 [767687.687307] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687309] end_request: I/O error, dev sdb,
> sector 50373231
> May 25 13:04:03 omc-2 [767687.687344] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687346] end_request: I/O error, dev sdb,
> sector 50379167
> May 25 13:04:03 omc-2 [767687.687356] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687358] end_request: I/O error, dev sdb,
> sector 50384503
> May 25 13:04:03 omc-2 [767687.687393] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687395] end_request: I/O error, dev sdb,
> sector 50394823
> May 25 13:04:03 omc-2 [767687.687405] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687410] end_request: I/O error, dev sdb,
> sector 50439527
> May 25 13:04:03 omc-2 [767687.687420] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687421] end_request: I/O error, dev sdb,
> sector 50476087
> May 25 13:04:03 omc-2 [767687.687449] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687451] end_request: I/O error, dev sdb,
> sector 50477671
> May 25 13:04:03 omc-2 [767687.687485] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687487] end_request: I/O error, dev sdb,
> sector 50489247
> May 25 13:04:03 omc-2 [767687.687496] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687498] end_request: I/O error, dev sdb,
> sector 50502599
> May 25 13:04:03 omc-2 [767687.687532] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687534] end_request: I/O error, dev sdb,
> sector 50503191
> May 25 13:04:03 omc-2 [767687.687544] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687546] end_request: I/O error, dev sdb,
> sector 50508127
> May 25 13:04:03 omc-2 [767687.687580] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687582] end_request: I/O error, dev sdb,
> sector 50509135
> May 25 13:04:03 omc-2 [767687.687591] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687593] end_request: I/O error, dev sdb,
> sector 50510359
> May 25 13:04:03 omc-2 [767687.687614] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687616] end_request: I/O error, dev sdb,
> sector 50513783
> May 25 13:04:03 omc-2 [767687.687623] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687625] end_request: I/O error, dev sdb,
> sector 50514879
> May 25 13:04:03 omc-2 [767687.687632] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687634] end_request: I/O error, dev sdb,
> sector 50517975
> May 25 13:04:03 omc-2 [767687.687641] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687643] end_request: I/O error, dev sdb,
> sector 50519215
> May 25 13:04:03 omc-2 [767687.687650] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687652] end_request: I/O error, dev sdb,
> sector 50520735
> May 25 13:04:03 omc-2 [767687.687659] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687661] end_request: I/O error, dev sdb,
> sector 50522575
> May 25 13:04:03 omc-2 [767687.687668] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687670] end_request: I/O error, dev sdb,
> sector 50525567
> May 25 13:04:03 omc-2 [767687.687677] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687679] end_request: I/O error, dev sdb,
> sector 50526703
> May 25 13:04:03 omc-2 [767687.687695] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687697] end_request: I/O error, dev sdb,
> sector 50530087
> May 25 13:04:03 omc-2 [767687.687704] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687706] end_request: I/O error, dev sdb,
> sector 50528103
> May 25 13:04:03 omc-2 [767687.687713] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687715] end_request: I/O error, dev sdb,
> sector 50531207
> May 25 13:04:03 omc-2 [767687.687718] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687724] end_request: I/O error, dev sdb,
> sector 50532343
> May 25 13:04:03 omc-2 [767687.687727] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687729] end_request: I/O error, dev sdb,
> sector 50534535
> May 25 13:04:03 omc-2 [767687.687736] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687738] end_request: I/O error, dev sdb,
> sector 50535615
> May 25 13:04:03 omc-2 [767687.687754] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687755] end_request: I/O error, dev sdb,
> sector 50536863
> May 25 13:04:03 omc-2 [767687.687762] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687764] end_request: I/O error, dev sdb,
> sector 50539047
> May 25 13:04:03 omc-2 [767687.687768] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687773] end_request: I/O error, dev sdb,
> sector 50540207
> May 25 13:04:03 omc-2 [767687.687777] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687782] end_request: I/O error, dev sdb,
> sector 50541407
> May 25 13:04:03 omc-2 [767687.687786] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687791] end_request: I/O error, dev sdb,
> sector 50543487
> May 25 13:04:03 omc-2 [767687.687795] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687797] end_request: I/O error, dev sdb,
> sector 50545695
> May 25 13:04:03 omc-2 [767687.687812] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687814] end_request: I/O error, dev sdb,
> sector 50548415
> May 25 13:04:03 omc-2 [767687.687821] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687823] end_request: I/O error, dev sdb,
> sector 50547111
> May 25 13:04:03 omc-2 [767687.687830] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687832] end_request: I/O error, dev sdb,
> sector 50551479
> May 25 13:04:03 omc-2 [767687.687839] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687841] end_request: I/O error, dev sdb,
> sector 50550407
> May 25 13:04:03 omc-2 [767687.687848] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687850] end_request: I/O error, dev sdb,
> sector 50555527
> May 25 13:04:03 omc-2 [767687.687857] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687858] end_request: I/O error, dev sdb,
> sector 50553695
> May 25 13:04:03 omc-2 [767687.687866] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687868] end_request: I/O error, dev sdb,
> sector 50558839
> May 25 13:04:03 omc-2 [767687.687874] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687876] end_request: I/O error, dev sdb,
> sector 50556871
> May 25 13:04:03 omc-2 [767687.687883] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687885] end_request: I/O error, dev sdb,
> sector 50561999
> May 25 13:04:03 omc-2 [767687.687893] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687895] end_request: I/O error, dev sdb,
> sector 50631359
> May 25 13:04:03 omc-2 [767687.687898] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687904] end_request: I/O error, dev sdb,
> sector 50627199
> May 25 13:04:03 omc-2 [767687.687907] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687912] end_request: I/O error, dev sdb,
> sector 50634191
> May 25 13:04:03 omc-2 [767687.687916] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687921] end_request: I/O error, dev sdb,
> sector 50636975
> May 25 13:04:03 omc-2 [767687.687925] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687931] end_request: I/O error, dev sdb,
> sector 50662359
> May 25 13:04:03 omc-2 [767687.687934] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687936] end_request: I/O error, dev sdb,
> sector 50664503
> May 25 13:04:03 omc-2 [767687.687951] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687953] end_request: I/O error, dev sdb,
> sector 50679127
> May 25 13:04:03 omc-2 [767687.687956] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687961] end_request: I/O error, dev sdb,
> sector 50667743
> May 25 13:04:03 omc-2 [767687.687965] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687970] end_request: I/O error, dev sdb,
> sector 50684319
> May 25 13:04:03 omc-2 [767687.687974] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687979] end_request: I/O error, dev sdb,
> sector 50686423
> May 25 13:04:03 omc-2 [767687.687983] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687988] end_request: I/O error, dev sdb,
> sector 50693967
> May 25 13:04:03 omc-2 [767687.687992] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.687994] end_request: I/O error, dev sdb,
> sector 50695631
> May 25 13:04:03 omc-2 [767687.688008] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688010] end_request: I/O error, dev sdb,
> sector 50697343
> May 25 13:04:03 omc-2 [767687.688017] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688019] end_request: I/O error, dev sdb,
> sector 50696343
> May 25 13:04:03 omc-2 [767687.688026] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688028] end_request: I/O error, dev sdb,
> sector 50698767
> May 25 13:04:03 omc-2 [767687.688031] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688037] end_request: I/O error, dev sdb,
> sector 50699455
> May 25 13:04:03 omc-2 [767687.688040] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688042] end_request: I/O error, dev sdb,
> sector 50702095
> May 25 13:04:03 omc-2 [767687.688049] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688051] end_request: I/O error, dev sdb,
> sector 50703871
> May 25 13:04:03 omc-2 [767687.688066] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688068] end_request: I/O error, dev sdb,
> sector 50704303
> May 25 13:04:03 omc-2 [767687.688075] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688076] end_request: I/O error, dev sdb,
> sector 50704127
> May 25 13:04:03 omc-2 [767687.688084] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688086] end_request: I/O error, dev sdb,
> sector 50707975
> May 25 13:04:03 omc-2 [767687.688093] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688095] end_request: I/O error, dev sdb,
> sector 50706559
> May 25 13:04:03 omc-2 [767687.688102] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688104] end_request: I/O error, dev sdb,
> sector 50710239
> May 25 13:04:03 omc-2 [767687.688107] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688112] end_request: I/O error, dev sdb,
> sector 50709287
> May 25 13:04:03 omc-2 [767687.688116] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688118] end_request: I/O error, dev sdb,
> sector 50711143
> May 25 13:04:03 omc-2 [767687.688125] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688127] end_request: I/O error, dev sdb,
> sector 50712031
> May 25 13:04:03 omc-2 [767687.688143] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688144] end_request: I/O error, dev sdb,
> sector 107262855
> May 25 13:04:03 omc-2 [767687.688151] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688153] end_request: I/O error, dev sdb,
> sector 71543247
> May 25 13:04:03 omc-2 [767687.688162] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688164] end_request: I/O error, dev sdb,
> sector 117097335
> May 25 13:04:03 omc-2 [767687.688171] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688173] end_request: I/O error, dev sdb,
> sector 232940408
> May 25 13:04:03 omc-2 [767687.688180] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688181] end_request: I/O error, dev sdb,
> sector 143631967
> May 25 13:04:03 omc-2 [767687.688189] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688191] end_request: I/O error, dev sdb,
> sector 232940415
> May 25 13:04:03 omc-2 [767687.688194] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688200] end_request: I/O error, dev sdb,
> sector 232940423
> May 25 13:04:03 omc-2 [767687.688209] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688211] end_request: I/O error, dev sdb,
> sector 232963255
> May 25 13:04:03 omc-2 [767687.688251] sd 0:4:1:0: SCSI error: return code
> = 0x00040001
> May 25 13:04:03 omc-2 [767687.688253] end_request: I/O error, dev sdb,
> sector 119
> May 25 13:04:03 omc-2 [767687.688290] I/O error in filesystem ("sdb1")
> meta-data dev sdb1 block 0x38       ("xfs_trans_read_buf") error 5 buf count
> 4096
> May 25 13:04:03 omc-2 [767691.711032] vmmon: Had to deallocate locked
> 351637 pages from vm driver ffff810196f62000
> May 25 13:04:03 omc-2 [767691.722922] vmmon: Had to deallocate AWE 5561
> pages from vm driver ffff810196f62000
> May 25 13:04:05 omc-2 gdm(pam_unix)[5924]: session closed for user colding
> May 25 13:04:05 omc-2 gdm[5924]: Error reinitilizing server
> May 25 13:04:09 omc-2 [767698.027401] xfs_force_shutdown(sdb1,0x1) called
> from line 424 of file fs/xfs/xfs_rw.c.  Return address = 0xffffffff803afb9a
> May 25 13:04:19 omc-2 [767707.439322] /dev/vmmon[6221]: host clock rate
> change request 83 -> 0
> May 25 13:04:19 omc-2 [767707.448144] vmmon: Had to deallocate locked 4813
> pages from vm driver ffff8101dfdba000
> May 25 13:04:19 omc-2 [767707.459108] vmmon: Had to deallocate AWE 4718
> pages from vm driver ffff8101dfdba000
> May 25 13:04:19 omc-2 [767707.474370] device eth0 left promiscuous mode
> May 25 13:04:19 omc-2 [767707.474376] bridge-eth0: disabled promiscuous
> mode
> May 25 13:04:37 omc-2 su[30149]: Successful su for root by colding
> May 25 13:04:37 omc-2 su[30149]: + pts/3 colding:root
> May 25 13:04:37 omc-2 su(pam_unix)[30149]: session opened for user root by
> (uid=1000)
> May 25 13:04:59 omc-2 gdm[5922]: Restarting computer...
> May 25 13:04:59 omc-2 shutdown[5922]: shutting down for system reboot
> May 25 13:04:59 omc-2 [767747.674922] xfs_force_shutdown(sdb1,0x1) called
> from line 424 of file fs/xfs/xfs_rw.c.  Return address = 0xffffffff803afb9a
> May 25 13:04:59 omc-2 init: Switching to runlevel: 6
> May 25 13:05:01 omc-2 cron[30539]: (jail) CMD (cd /home/jail/BOINC ;
> ./boinc -return_results_immediately &>/dev/null)
> May 25 13:05:02 omc-2 sshd[5777]: Received signal 15; terminating.
> May 25 13:05:02 omc-2 spamd[5714]: spamd: server killed by SIGTERM,
> shutting down
> May 25 13:05:03 omc-2 [767751.374204] xfs_force_shutdown(sdb1,0x1) called
> from line 424 of file fs/xfs/xfs_rw.c.  Return address = 0xffffffff803afb9a
> May 25 13:05:05 omc-2 [767753.706435] /dev/vmmon[31085]: Module vmmon:
> unloaded
> May 25 13:05:05 omc-2 [767753.764389] bridge-eth0: down
> May 25 13:05:05 omc-2 [767753.764503] bridge-eth0: detached
> May 25 13:05:06 omc-2 dnsmasq[7883]: exiting on receipt of SIGTERM
> May 25 13:05:07 omc-2 dhcpcd[5131]: eth0: received SIGTERM, stopping
> May 25 13:05:07 omc-2 dhcpcd[5131]: eth0: removing default route via
> 192.168.0.1 metric 0
> May 25 13:05:07 omc-2 dhcpcd[5131]: eth0: deleting IP address
> 192.168.0.2/24
> May 25 13:05:07 omc-2 dhcpcd[5131]: eth0: exiting
> May 25 13:05:07 omc-2 [767755.948308] PM: Writing back config space on
> device 0000:03:09.0 at offset b (was 164714e4, writing 288510f1)
> May 25 13:05:07 omc-2 [767755.948319] PM: Writing back config space on
> device 0000:03:09.0 at offset 3 (was 4000, writing 4010)
> May 25 13:05:07 omc-2 [767755.948324] PM: Writing back config space on
> device 0000:03:09.0 at offset 2 (was 2000000, writing 2000002)
> May 25 13:05:07 omc-2 [767755.948328] PM: Writing back config space on
> device 0000:03:09.0 at offset 1 (was 2b00000, writing 2b00106)
> May 25 13:05:07 omc-2 [767755.948334] PM: Writing back config space on
> device 0000:03:09.0 at offset 0 (was 164714e4, writing 16a714e4)
> May 25 13:05:08 omc-2 syslog-ng[4655]: syslog-ng version 1.6.11 going down
>
>
>
> --
> gentoo-user@g.o mailing list
>
>