| 1 |
I posted the stuff below on the mythtvtalk forum and it's been a few |
| 2 |
days and I've heard nothing. I've also searched for answers |
| 3 |
elsewhere, but no go. Since I'm running my setup under gentoo, I |
| 4 |
thought I try this list. I hope you don't mind. |
| 5 |
|
| 6 |
I recently acquired a new Hauppauge WinTV 1600 and have successfully |
| 7 |
gotten the analog side working with the analog channels (1-99). That |
| 8 |
is, I can plug my (Comcast) cable from the wall to the tuner card's |
| 9 |
analog input and get the basic cable channels. |
| 10 |
|
| 11 |
However, the whole reason for getting tv tuner card and mythtv was to |
| 12 |
record japanTV, which is beyond channel 99 and requires a set top box |
| 13 |
to watch it on the TV. I've read the installation instructions for the |
| 14 |
ATSC input of the card but I'm having problems and am aware of the IR |
| 15 |
blaster option. |
| 16 |
|
| 17 |
I suppose the main problem . . . the one causing the other problems |
| 18 |
like not getting any channels is that mythtv is not "seeing" my card. |
| 19 |
When I go to configure the capture card there is not DVB DTV card type |
| 20 |
offered, which suggests to me that card is not being "seen." |
| 21 |
|
| 22 |
Suggestions? |
| 23 |
|
| 24 |
I have posted below some various info, but before that I want to ask |
| 25 |
one more thing, if all were fine, should it be the case that I plug |
| 26 |
the cable from the wall to the ATSC input (i.e., not through the set |
| 27 |
top box) and it just work (as if it were the set top box)? |
| 28 |
|
| 29 |
Thanks for your time. |
| 30 |
-neal |
| 31 |
|
| 32 |
russell ~ # uname -a |
| 33 |
Linux russell 2.6.30-gentoo-r5 #1 SMP Sun Aug 30 04:58:43 CDT 2009 |
| 34 |
i686 AMD Athlon(tm) Processor AuthenticAMD GNU/Linux |
| 35 |
|
| 36 |
|
| 37 |
russell ~ # dmesg | grep cx18 |
| 38 |
cx18: Start initialization, version 1.2.0 |
| 39 |
cx18-0: Initializing card 0 |
| 40 |
cx18-0: Autodetected Hauppauge card |
| 41 |
cx18 0000:00:11.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11 |
| 42 |
cx18-0: Unreasonably low latency timer, setting to 64 (was 32) |
| 43 |
cx18-0: cx23418 revision 01010000 (B) |
| 44 |
cx18-0: Autodetected Hauppauge HVR-1600 |
| 45 |
cx18-0: Simultaneous Digital and Analog TV capture supported |
| 46 |
IRQ 11/cx18-0: IRQF_DISABLED is not guaranteed on shared IRQs |
| 47 |
tuner 2-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) |
| 48 |
cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0) |
| 49 |
cx18-0: Registered device video0 for encoder MPEG (64 x 32 kB) |
| 50 |
DVB: registering new adapter (cx1 |
| 51 |
cx18-0: DVB Frontend registered |
| 52 |
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB) |
| 53 |
cx18-0: Registered device video32 for encoder YUV (16 x 128 kB) |
| 54 |
cx18-0: Registered device vbi0 for encoder VBI (20 x 51984 bytes) |
| 55 |
cx18-0: Registered device video24 for encoder PCM audio (256 x 4 kB) |
| 56 |
cx18-0: Initialized card: Hauppauge HVR-1600 |
| 57 |
cx18: End initialization |
| 58 |
russell ~ # dmesg | grep DVB |
| 59 |
DVB: registering new adapter (cx1 |
| 60 |
DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... |
| 61 |
cx18-0: DVB Frontend registered |
| 62 |
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB) |
| 63 |
|
| 64 |
lspci -v output: |
| 65 |
00:11.0 Multimedia video controller: Conexant CX23418 Single-Chip |
| 66 |
MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder |
| 67 |
Subsystem: Hauppauge computer works Inc. Device 7444 |
| 68 |
Flags: bus master, medium devsel, latency 64, IRQ 11 |
| 69 |
Memory at f0000000 (32-bit, non-prefetchable) [size=64M] |
| 70 |
Capabilities: [44] Vital Product Data <?> |
| 71 |
Capabilities: [4c] Power Management version 2 |
| 72 |
Kernel driver in use: cx18 |
| 73 |
Kernel modules: cx18 |
Archives