| 1 |
I have a USB PCI card which stopped working, meaning my scanner stopped |
| 2 |
being detected. The problem remains also under KNOPPIX. |
| 3 |
Can I assume the card is dead? (But it is recognized, sort of...) |
| 4 |
|
| 5 |
Partial output of lspci -vvv (as root): |
| 6 |
02:0c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) |
| 7 |
Subsystem: ALi Corporation USB 1.1 Controller |
| 8 |
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- |
| 9 |
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ |
| 10 |
Interrupt: pin B routed to IRQ 5 |
| 11 |
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [disabled] |
| 12 |
Capabilities: [60] <chain broken> |
| 13 |
|
| 14 |
02:0c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) |
| 15 |
Subsystem: ALi Corporation USB 1.1 Controller |
| 16 |
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- |
| 17 |
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ |
| 18 |
Interrupt: pin C routed to IRQ 11 |
| 19 |
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [disabled] |
| 20 |
Capabilities: [60] <chain broken> |
| 21 |
|
| 22 |
02:0c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) |
| 23 |
Subsystem: ALi Corporation USB 1.1 Controller |
| 24 |
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- |
| 25 |
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ |
| 26 |
Interrupt: pin D routed to IRQ 11 |
| 27 |
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [disabled] |
| 28 |
Capabilities: [60] <chain broken> |
| 29 |
|
| 30 |
02:0c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if 20 [EHCI]) |
| 31 |
Subsystem: Unknown device 2020:8888 |
| 32 |
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- |
| 33 |
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ |
| 34 |
Interrupt: pin A routed to IRQ 11 |
| 35 |
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [disabled] |
| 36 |
Capabilities: [50] <chain broken> |
| 37 |
|
| 38 |
dmesg: (sorry for the long message) |
| 39 |
|
| 40 |
Linux version 2.6.15-gentoo-r1 (root@moria) (gcc version 3.3.6 (Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #1 SMP PREEMPT Fri Jan 27 15:16:19 WET 2006 |
| 41 |
BIOS-provided physical RAM map: |
| 42 |
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) |
| 43 |
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) |
| 44 |
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) |
| 45 |
BIOS-e820: 0000000000100000 - 000000001ffeb000 (usable) |
| 46 |
BIOS-e820: 000000001ffeb000 - 000000001ffef000 (ACPI data) |
| 47 |
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved) |
| 48 |
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) |
| 49 |
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) |
| 50 |
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) |
| 51 |
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) |
| 52 |
511MB LOWMEM available. |
| 53 |
On node 0 totalpages: 131051 |
| 54 |
DMA zone: 4096 pages, LIFO batch:0 |
| 55 |
DMA32 zone: 0 pages, LIFO batch:0 |
| 56 |
Normal zone: 126955 pages, LIFO batch:31 |
| 57 |
HighMem zone: 0 pages, LIFO batch:0 |
| 58 |
DMI 2.3 present. |
| 59 |
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) |
| 60 |
Built 1 zonelists |
| 61 |
Kernel command line: root=/dev/hda5 video=vesafb:ywrap,mtrr vga=0x31a pci=usepirqmask |
| 62 |
Found and enabled local APIC! |
| 63 |
mapped APIC to ffffd000 (fee00000) |
| 64 |
Initializing CPU#0 |
| 65 |
PID hash table entries: 2048 (order: 11, 32768 bytes) |
| 66 |
Detected 1506.827 MHz processor. |
| 67 |
Using tsc for high-res timesource |
| 68 |
Console: colour dummy device 80x25 |
| 69 |
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) |
| 70 |
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) |
| 71 |
Memory: 514696k/524204k available (2069k kernel code, 9000k reserved, 845k data, 172k init, 0k highmem) |
| 72 |
Checking if this processor honours the WP bit even in supervisor mode... Ok. |
| 73 |
Calibrating delay using timer specific routine.. 3018.88 BogoMIPS (lpj=6037760) |
| 74 |
Mount-cache hash table entries: 512 |
| 75 |
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 |
| 76 |
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 |
| 77 |
CPU: Trace cache: 12K uops, L1 D cache: 8K |
| 78 |
CPU: L2 cache: 256K |
| 79 |
CPU: Hyper-Threading is disabled |
| 80 |
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000 00000000 00000000 |
| 81 |
Intel machine check architecture supported. |
| 82 |
Intel machine check reporting enabled on CPU#0. |
| 83 |
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available |
| 84 |
CPU0: Thermal monitoring enabled |
| 85 |
mtrr: v2.0 (20020519) |
| 86 |
Enabling fast FPU save and restore... done. |
| 87 |
Enabling unmasked SIMD FPU exception support... done. |
| 88 |
Checking 'hlt' instruction... OK. |
| 89 |
CPU0: Intel(R) Pentium(R) 4 CPU 1.50GHz stepping 02 |
| 90 |
SMP motherboard not detected. |
| 91 |
Brought up 1 CPUs |
| 92 |
NET: Registered protocol family 16 |
| 93 |
PCI: PCI BIOS revision 2.10 entry at 0xf0ed0, last bus=2 |
| 94 |
PCI: Using configuration type 1 |
| 95 |
SCSI subsystem initialized |
| 96 |
usbcore: registered new driver usbfs |
| 97 |
usbcore: registered new driver hub |
| 98 |
PCI: Probing PCI hardware |
| 99 |
PCI: Probing PCI hardware (bus 00) |
| 100 |
PCI quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO |
| 101 |
PCI quirk: region ec00-ec3f claimed by ICH4 GPIO |
| 102 |
Boot video device is 0000:01:00.0 |
| 103 |
PCI: Transparent bridge - 0000:00:1e.0 |
| 104 |
PCI: Using IRQ router PIIX/ICH [8086/2440] at 0000:00:1f.0 |
| 105 |
PCI: Found IRQ 9 for device 0000:02:0b.0 |
| 106 |
PCI: Sharing IRQ 9 with 0000:00:1f.4 |
| 107 |
IRQ routing conflict for 0000:02:0c.2, have irq 11, want irq 9 |
| 108 |
PCI: Found IRQ 3 for device 0000:02:0d.2 |
| 109 |
PCI: Sharing IRQ 3 with 0000:00:1f.2 |
| 110 |
PCI: Bridge: 0000:00:01.0 |
| 111 |
IO window: d000-dfff |
| 112 |
MEM window: ef000000-efdfffff |
| 113 |
PREFETCH window: eff00000-f7ffffff |
| 114 |
PCI: Bridge: 0000:00:1e.0 |
| 115 |
IO window: b000-bfff |
| 116 |
MEM window: ed800000-eeffffff |
| 117 |
PREFETCH window: efe00000-efefffff |
| 118 |
PCI: Setting latency timer of device 0000:00:01.0 to 64 |
| 119 |
PCI: Setting latency timer of device 0000:00:1e.0 to 64 |
| 120 |
Machine check exception polling timer started. |
| 121 |
Installing knfsd (copyright (C) 1996 okir@×××××××××.de). |
| 122 |
io scheduler noop registered |
| 123 |
io scheduler anticipatory registered |
| 124 |
io scheduler deadline registered |
| 125 |
io scheduler cfq registered |
| 126 |
0000:00:1f.2: uhci_check_and_reset_hc: legsup = 0x053a |
| 127 |
0000:00:1f.2: Performing full reset |
| 128 |
0000:00:1f.4: uhci_check_and_reset_hc: legsup = 0x0010 |
| 129 |
0000:00:1f.4: Performing full reset |
| 130 |
PCI: Found IRQ 11 for device 0000:01:00.0 |
| 131 |
radeonfb: Found Intel x86 BIOS ROM Image |
| 132 |
radeonfb: Retreived PLL infos from BIOS |
| 133 |
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=290.00 Mhz, System=230.00 MHz |
| 134 |
radeonfb: PLL min 20000 max 35000 |
| 135 |
radeonfb: Monitor 1 type DFP found |
| 136 |
radeonfb: EDID probed |
| 137 |
radeonfb: Monitor 2 type no found |
| 138 |
Console: switching to colour frame buffer device 160x64 |
| 139 |
radeonfb (0000:01:00.0): ATI Radeon QW |
| 140 |
vesafb: cannot reserve video memory at 0xf0000000 |
| 141 |
vesafb: framebuffer at 0xf0000000, mapped to 0xe1900000, using 5120k, total 65536k |
| 142 |
vesafb: mode is 1280x1024x16, linelength=2560, pages=24 |
| 143 |
vesafb: protected mode interface info at c000:5460 |
| 144 |
vesafb: pmi: set display start = c00c54f4, set palette = c00c5540 |
| 145 |
vesafb: pmi: ports = d810 d816 d854 d838 d83c d85c d800 d804 d8b0 d8b2 d8b4 |
| 146 |
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=2048 |
| 147 |
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 |
| 148 |
vesafb: Mode is VGA compatible |
| 149 |
fb1: VESA VGA frame buffer device |
| 150 |
Linux agpgart interface v0.101 (c) Dave Jones |
| 151 |
agpgart: Detected an Intel i850 Chipset. |
| 152 |
agpgart: AGP aperture is 64M @ 0xf8000000 |
| 153 |
[drm] Initialized drm 1.0.0 20040925 |
| 154 |
PCI: Found IRQ 11 for device 0000:01:00.0 |
| 155 |
[drm] Initialized radeon 1.19.0 20050911 on minor 0: |
| 156 |
serio: i8042 AUX port at 0x60,0x64 irq 12 |
| 157 |
serio: i8042 KBD port at 0x60,0x64 irq 1 |
| 158 |
mice: PS/2 mouse device common for all mice |
| 159 |
input: AT Translated Set 2 keyboard as /class/input/input0 |
| 160 |
floppy0: no floppy controllers found |
| 161 |
8139too Fast Ethernet driver 0.9.27 |
| 162 |
PCI: Enabling device 0000:02:0b.0 (0004 -> 0007) |
| 163 |
PCI: Found IRQ 9 for device 0000:02:0b.0 |
| 164 |
PCI: Sharing IRQ 9 with 0000:00:1f.4 |
| 165 |
IRQ routing conflict for 0000:02:0c.2, have irq 11, want irq 9 |
| 166 |
eth0: RealTek RTL8139 at 0xb800, 00:50:fc:4c:9e:08, IRQ 9 |
| 167 |
eth0: Identified 8139 chip type 'RTL-8139C' |
| 168 |
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 |
| 169 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
| 170 |
ICH2: IDE controller at PCI slot 0000:00:1f.1 |
| 171 |
ICH2: chipset revision 18 |
| 172 |
ICH2: not 100% native mode: will probe irqs later |
| 173 |
ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:DMA |
| 174 |
ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:DMA, hdd:DMA |
| 175 |
Probing IDE interface ide0... |
| 176 |
hda: ST340016A, ATA DISK drive |
| 177 |
hdb: ST380021A, ATA DISK drive |
| 178 |
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 |
| 179 |
Probing IDE interface ide1... |
| 180 |
hdc: HL-DT-ST GCE-8160B, ATAPI CD/DVD-ROM drive |
| 181 |
hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive |
| 182 |
ide1 at 0x170-0x177,0x376 on irq 15 |
| 183 |
hda: max request size: 128KiB |
| 184 |
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) |
| 185 |
hda: cache flushes not supported |
| 186 |
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 > |
| 187 |
hdb: max request size: 128KiB |
| 188 |
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) |
| 189 |
hdb: cache flushes not supported |
| 190 |
hdb: hdb1 hdb2 hdb3 hdb4 |
| 191 |
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, DMA |
| 192 |
Uniform CD-ROM driver Revision: 3.20 |
| 193 |
hdd: ATAPI 16X DVD-ROM drive, 512kB Cache, UDMA(33) |
| 194 |
libata version 1.20 loaded. |
| 195 |
usbmon: debugfs is not available |
| 196 |
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 |
| 197 |
PCI: setting IRQ 11 as level-triggered |
| 198 |
PCI: Assigned IRQ 11 for device 0000:02:0c.3 |
| 199 |
ehci_hcd 0000:02:0c.3: controller already in use |
| 200 |
ehci_hcd 0000:02:0c.3: init 0000:02:0c.3 fail, -16 |
| 201 |
ehci_hcd: probe of 0000:02:0c.3 failed with error -16 |
| 202 |
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) |
| 203 |
ohci_hcd: block sizes: ed 64 td 64 |
| 204 |
PCI: setting IRQ 5 as level-triggered |
| 205 |
PCI: Assigned IRQ 5 for device 0000:02:0c.0 |
| 206 |
ohci_hcd 0000:02:0c.0: controller already in use |
| 207 |
ohci_hcd 0000:02:0c.0: init 0000:02:0c.0 fail, -16 |
| 208 |
ohci_hcd: probe of 0000:02:0c.0 failed with error -16 |
| 209 |
PCI: Assigned IRQ 11 for device 0000:02:0c.1 |
| 210 |
ohci_hcd 0000:02:0c.1: controller already in use |
| 211 |
ohci_hcd 0000:02:0c.1: init 0000:02:0c.1 fail, -16 |
| 212 |
ohci_hcd: probe of 0000:02:0c.1 failed with error -16 |
| 213 |
PCI: Found IRQ 9 for device 0000:02:0c.2 |
| 214 |
PCI: Sharing IRQ 9 with 0000:00:1f.4 |
| 215 |
PCI: Sharing IRQ 9 with 0000:02:0b.0 |
| 216 |
IRQ routing conflict for 0000:02:0c.2, have irq 11, want irq 9 |
| 217 |
ohci_hcd 0000:02:0c.2: controller already in use |
| 218 |
ohci_hcd 0000:02:0c.2: init 0000:02:0c.2 fail, -16 |
| 219 |
ohci_hcd: probe of 0000:02:0c.2 failed with error -16 |
| 220 |
USB Universal Host Controller Interface driver v2.3 |
| 221 |
PCI: Found IRQ 3 for device 0000:00:1f.2 |
| 222 |
PCI: Sharing IRQ 3 with 0000:02:0d.2 |
| 223 |
PCI: Setting latency timer of device 0000:00:1f.2 to 64 |
| 224 |
uhci_hcd 0000:00:1f.2: UHCI Host Controller |
| 225 |
uhci_hcd 0000:00:1f.2: detected 2 ports |
| 226 |
uhci_hcd 0000:00:1f.2: uhci_check_and_reset_hc: cmd = 0x0000 |
| 227 |
uhci_hcd 0000:00:1f.2: Performing full reset |
| 228 |
drivers/usb/core/inode.c: creating file 'devices' |
| 229 |
drivers/usb/core/inode.c: creating file '001' |
| 230 |
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 |
| 231 |
uhci_hcd 0000:00:1f.2: irq 3, io base 0x0000a400 |
| 232 |
usb usb1: default language 0x0409 |
| 233 |
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 |
| 234 |
usb usb1: Product: UHCI Host Controller |
| 235 |
usb usb1: Manufacturer: Linux 2.6.15-gentoo-r1 uhci_hcd |
| 236 |
usb usb1: SerialNumber: 0000:00:1f.2 |
| 237 |
usb usb1: hotplug |
| 238 |
usb usb1: adding 1-0:1.0 (config #1, interface 0) |
| 239 |
usb 1-0:1.0: hotplug |
| 240 |
hub 1-0:1.0: usb_probe_interface |
| 241 |
hub 1-0:1.0: usb_probe_interface - got id |
| 242 |
hub 1-0:1.0: USB hub found |
| 243 |
hub 1-0:1.0: 2 ports detected |
| 244 |
hub 1-0:1.0: standalone hub |
| 245 |
hub 1-0:1.0: no power switching (usb 1.0) |
| 246 |
hub 1-0:1.0: individual port over-current protection |
| 247 |
hub 1-0:1.0: power on to power good time: 2ms |
| 248 |
hub 1-0:1.0: local power source is good |
| 249 |
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0000 |
| 250 |
drivers/usb/core/inode.c: creating file '001' |
| 251 |
uhci_hcd 0000:00:1f.2: port 1 portsc 01ab,00 |
| 252 |
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s |
| 253 |
PCI: Found IRQ 9 for device 0000:00:1f.4 |
| 254 |
PCI: Sharing IRQ 9 with 0000:02:0b.0 |
| 255 |
IRQ routing conflict for 0000:02:0c.2, have irq 11, want irq 9 |
| 256 |
PCI: Setting latency timer of device 0000:00:1f.4 to 64 |
| 257 |
uhci_hcd 0000:00:1f.4: UHCI Host Controller |
| 258 |
uhci_hcd 0000:00:1f.4: detected 2 ports |
| 259 |
uhci_hcd 0000:00:1f.4: uhci_check_and_reset_hc: cmd = 0x0000 |
| 260 |
uhci_hcd 0000:00:1f.4: Performing full reset |
| 261 |
drivers/usb/core/inode.c: creating file '002' |
| 262 |
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2 |
| 263 |
uhci_hcd 0000:00:1f.4: irq 9, io base 0x0000a000 |
| 264 |
usb usb2: default language 0x0409 |
| 265 |
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 |
| 266 |
usb usb2: Product: UHCI Host Controller |
| 267 |
usb usb2: Manufacturer: Linux 2.6.15-gentoo-r1 uhci_hcd |
| 268 |
usb usb2: SerialNumber: 0000:00:1f.4 |
| 269 |
usb usb2: hotplug |
| 270 |
usb usb2: adding 2-0:1.0 (config #1, interface 0) |
| 271 |
usb 2-0:1.0: hotplug |
| 272 |
hub 2-0:1.0: usb_probe_interface |
| 273 |
hub 2-0:1.0: usb_probe_interface - got id |
| 274 |
hub 2-0:1.0: USB hub found |
| 275 |
hub 2-0:1.0: 2 ports detected |
| 276 |
hub 2-0:1.0: standalone hub |
| 277 |
hub 2-0:1.0: no power switching (usb 1.0) |
| 278 |
hub 2-0:1.0: individual port over-current protection |
| 279 |
hub 2-0:1.0: power on to power good time: 2ms |
| 280 |
hub 2-0:1.0: local power source is good |
| 281 |
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 |
| 282 |
drivers/usb/core/inode.c: creating file '001' |
| 283 |
Initializing USB Mass Storage driver... |
| 284 |
usb 1-1: new low speed USB device using uhci_hcd and address 2 |
| 285 |
usb 1-1: skipped 1 descriptor after interface |
| 286 |
usb 1-1: default language 0x0409 |
| 287 |
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0 |
| 288 |
usb 1-1: Product: USB-PS/2 Optical Mouse |
| 289 |
usb 1-1: Manufacturer: Logitech |
| 290 |
usb 1-1: hotplug |
| 291 |
usb 1-1: adding 1-1:1.0 (config #1, interface 0) |
| 292 |
usb 1-1:1.0: hotplug |
| 293 |
drivers/usb/core/inode.c: creating file '002' |
| 294 |
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000 |
| 295 |
usbcore: registered new driver usb-storage |
| 296 |
USB Mass Storage support registered. |
| 297 |
usbhid 1-1:1.0: usb_probe_interface |
| 298 |
usbhid 1-1:1.0: usb_probe_interface - got id |
| 299 |
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1 |
| 300 |
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1f.2-1 |
| 301 |
usbcore: registered new driver usbhid |
| 302 |
drivers/usb/input/hid-core.c: v2.6:USB HID core driver |
| 303 |
oprofile: using NMI interrupt. |
| 304 |
NET: Registered protocol family 2 |
| 305 |
IP route cache hash table entries: 8192 (order: 3, 32768 bytes) |
| 306 |
TCP established hash table entries: 32768 (order: 6, 393216 bytes) |
| 307 |
TCP bind hash table entries: 32768 (order: 6, 393216 bytes) |
| 308 |
TCP: Hash tables configured (established 32768 bind 32768) |
| 309 |
TCP reno registered |
| 310 |
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 212 bytes per conntrack |
| 311 |
ip_tables: (C) 2000-2002 Netfilter core team |
| 312 |
ipt_recent v0.3.1: Stephen Frost <sfrost@×××××××.net>. http://snowman.net/projects/ipt_recent/ |
| 313 |
arp_tables: (C) 2002 David S. Miller |
| 314 |
TCP bic registered |
| 315 |
NET: Registered protocol family 1 |
| 316 |
NET: Registered protocol family 17 |
| 317 |
Using IPI Shortcut mode |
| 318 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 319 |
VFS: Mounted root (ext3 filesystem) readonly. |
| 320 |
Freeing unused kernel memory: 172k freed |
| 321 |
kjournald starting. Commit interval 5 seconds |
| 322 |
uhci_hcd 0000:00:1f.4: suspend_rh (auto-stop) |
| 323 |
Adding 522072k swap on /dev/hda6. Priority:-1 extents:1 across:522072k |
| 324 |
Adding 265032k swap on /dev/hda7. Priority:-2 extents:1 across:265032k |
| 325 |
EXT3 FS on hda5, internal journal |
| 326 |
kjournald starting. Commit interval 5 seconds |
| 327 |
EXT3 FS on hdb2, internal journal |
| 328 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 329 |
kjournald starting. Commit interval 5 seconds |
| 330 |
EXT3 FS on hda13, internal journal |
| 331 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 332 |
kjournald starting. Commit interval 5 seconds |
| 333 |
EXT3 FS on hda3, internal journal |
| 334 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 335 |
kjournald starting. Commit interval 5 seconds |
| 336 |
EXT3 FS on hda11, internal journal |
| 337 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 338 |
kjournald starting. Commit interval 5 seconds |
| 339 |
EXT3 FS on hdb1, internal journal |
| 340 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 341 |
kjournald starting. Commit interval 5 seconds |
| 342 |
EXT3 FS on hda10, internal journal |
| 343 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 344 |
PCI: Enabling device 0000:02:0d.0 (0004 -> 0005) |
| 345 |
PCI: Assigned IRQ 5 for device 0000:02:0d.0 |
| 346 |
Installing spdif_bug patch: Audigy 2 [SB0240] |
| 347 |
PCI: Enabling device 0000:02:0d.1 (0004 -> 0005) |
| 348 |
gameport: EMU10K1 is pci0000:02:0d.1/gameport0, io 0xb000, speed 946kHz |
| 349 |
cdrom: open failed. |
| 350 |
cdrom: open failed. |
| 351 |
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 |
| 352 |
ipt_owner: pid, sid and command matching not supported anymore |
| 353 |
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. |
| 354 |
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode |
| 355 |
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode |
| 356 |
|
| 357 |
|
| 358 |
-- |
| 359 |
Jorge Almeida |
| 360 |
-- |
| 361 |
gentoo-user@g.o mailing list |
Archives