1 |
On Tue, 13 Nov 2007 22:27:52 +0100 Till Schwalbe <gentoo@×××××××.de> |
2 |
wrote: |
3 |
> |
4 |
>Und was hat das Ganze jetzt mit iwl und kismet zu tun? |
5 |
> |
6 |
> |
7 |
|
8 |
Oh, verdammt, da dachte ich wohl, wenn ich das "Subject" ändere, kann |
9 |
ich auch eine Nachricht mittels Antworten erstellen. |
10 |
Immerhin habe ich mal nen Blick af Message-header |
11 |
geworfen...naja vorher wusste ich nichts von "replay-to:". |
12 |
|
13 |
Ansonsten ist dies natürlich auch meine Entschuldigung für den |
14 |
"eingefügten" Beitrag im "iwl und kismet". |
15 |
|
16 |
> Hallo, |
17 |
> |
18 |
> Seit längerer Zeit plagt mich das Problem, dass mein einer |
19 |
> USB-Port (Bus 5) stockend arbeitet. Egal, was für eine Peripherie ich |
20 |
> dran hab'. Unter Windows kann ich das Phänomen, genauso wie an dem |
21 |
> zweiten Port (Bus 4), nicht beobachten. Damit schließe ich einen |
22 |
> Defekt der Hardware aus. |
23 |
> Das "stocken" kommt meistens erst nach einiger Zeit, setzt manchmal |
24 |
> wieder aus, usw. : |
25 |
> |
26 |
> # lsusb |
27 |
> Bus 001 Device 001: ID 0000:0000 |
28 |
> Bus 005 Device 002: ID 046d:c016 Logitech, Inc. M-UV69a Optical Wheel |
29 |
> Mouse |
30 |
> Bus 005 Device 001: ID 0000:0000 |
31 |
> Bus 004 Device 002: ID 0ccd:0013 TerraTec Electronic GmbH |
32 |
> Bus 004 Device 001: ID 0000:0000 |
33 |
> Bus 003 Device 001: ID 0000:0000 |
34 |
> Bus 002 Device 001: ID 0000:0000 |
35 |
> |
36 |
> #dmesg Zeigt nichts an Veränderungen an |
37 |
> |
38 |
> (Weitere Ausgaben weiter unten) |
39 |
> |
40 |
> Ich hoffe, ihr könnt mir zur weiteren Fehleranalyse, oder -bewältigung |
41 |
> behilflich sein. |
42 |
> |
43 |
> MfG, |
44 |
> Jan |
45 |
> |
46 |
> |
47 |
> |
48 |
> |
49 |
> |
50 |
> |
51 |
> #lspci (gekürzt) |
52 |
> 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB |
53 |
> UHCI Controller #1 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu |
54 |
> Siemens Computer GmbH Unknown device 10b0 Flags: bus master, medium |
55 |
> devsel, latency 0, IRQ 5 I/O ports at 1800 [size=32] |
56 |
> |
57 |
> 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB |
58 |
> UHCI Controller #2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu |
59 |
> Siemens Computer GmbH Unknown device 10b0 Flags: bus master, medium |
60 |
> devsel, latency 0, IRQ 11 I/O ports at 1820 [size=32] |
61 |
> |
62 |
> 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB |
63 |
> UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu |
64 |
> Siemens Computer GmbH Unknown device 10b0 Flags: bus master, medium |
65 |
> devsel, latency 0, IRQ 3 I/O ports at 1840 [size=32] |
66 |
> |
67 |
> 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB |
68 |
> UHCI Controller #4 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu |
69 |
> Siemens Computer GmbH Unknown device 10b0 Flags: bus master, medium |
70 |
> devsel, latency 0, IRQ 10 I/O ports at 1860 [size=32] |
71 |
> |
72 |
> 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 |
73 |
> EHCI Controller (rev 02) (prog-if 20 [EHCI]) Subsystem: Fujitsu |
74 |
> Siemens Computer GmbH Unknown device 10b0 Flags: bus master, medium |
75 |
> devsel, latency 0, IRQ 5 Memory at b0004000 (32-bit, |
76 |
> non-prefetchable) [size=1K] Capabilities: [50] Power Management |
77 |
> version 2 Capabilities: [58] Debug port |
78 |
> |
79 |
> |
80 |
> #lsusb -v (vom Bus 005) |
81 |
> Bus 005 Device 002: ID 046d:c016 Logitech, Inc. M-UV69a Optical Wheel |
82 |
> Mouse Device Descriptor: |
83 |
> bLength 18 |
84 |
> bDescriptorType 1 |
85 |
> bcdUSB 2.00 |
86 |
> bDeviceClass 0 (Defined at Interface level) |
87 |
> bDeviceSubClass 0 |
88 |
> bDeviceProtocol 0 |
89 |
> bMaxPacketSize0 8 |
90 |
> idVendor 0x046d Logitech, Inc. |
91 |
> idProduct 0xc016 M-UV69a Optical Wheel Mouse |
92 |
> bcdDevice 3.40 |
93 |
> iManufacturer 1 Logitech |
94 |
> iProduct 2 Optical USB Mouse |
95 |
> iSerial 0 |
96 |
> bNumConfigurations 1 |
97 |
> Configuration Descriptor: |
98 |
> bLength 9 |
99 |
> bDescriptorType 2 |
100 |
> wTotalLength 34 |
101 |
> bNumInterfaces 1 |
102 |
> bConfigurationValue 1 |
103 |
> iConfiguration 0 |
104 |
> bmAttributes 0xa0 |
105 |
> (Bus Powered) |
106 |
> Remote Wakeup |
107 |
> MaxPower 100mA |
108 |
> Interface Descriptor: |
109 |
> bLength 9 |
110 |
> bDescriptorType 4 |
111 |
> bInterfaceNumber 0 |
112 |
> bAlternateSetting 0 |
113 |
> bNumEndpoints 1 |
114 |
> bInterfaceClass 3 Human Interface Devices |
115 |
> bInterfaceSubClass 1 Boot Interface Subclass |
116 |
> bInterfaceProtocol 2 Mouse |
117 |
> iInterface 0 |
118 |
> HID Device Descriptor: |
119 |
> bLength 9 |
120 |
> bDescriptorType 33 |
121 |
> bcdHID 1.10 |
122 |
> bCountryCode 0 Not supported |
123 |
> bNumDescriptors 1 |
124 |
> bDescriptorType 34 Report |
125 |
> wDescriptorLength 52 |
126 |
> Report Descriptors: |
127 |
> ** UNAVAILABLE ** |
128 |
> Endpoint Descriptor: |
129 |
> bLength 7 |
130 |
> bDescriptorType 5 |
131 |
> bEndpointAddress 0x81 EP 1 IN |
132 |
> bmAttributes 3 |
133 |
> Transfer Type Interrupt |
134 |
> Synch Type None |
135 |
> Usage Type Data |
136 |
> wMaxPacketSize 0x0004 1x 4 bytes |
137 |
> bInterval 10 |
138 |
> Device Status: 0x0000 |
139 |
> (Bus Powered) |
140 |
> |
141 |
> Bus 005 Device 001: ID 0000:0000 |
142 |
> Device Descriptor: |
143 |
> bLength 18 |
144 |
> bDescriptorType 1 |
145 |
> bcdUSB 1.10 |
146 |
> bDeviceClass 9 Hub |
147 |
> bDeviceSubClass 0 Unused |
148 |
> bDeviceProtocol 0 |
149 |
> bMaxPacketSize0 64 |
150 |
> idVendor 0x0000 |
151 |
> idProduct 0x0000 |
152 |
> bcdDevice 2.06 |
153 |
> iManufacturer 3 Linux 2.6.22-gentoo-r9 uhci_hcd |
154 |
> iProduct 2 UHCI Host Controller |
155 |
> iSerial 1 0000:00:1d.3 |
156 |
> bNumConfigurations 1 |
157 |
> Configuration Descriptor: |
158 |
> bLength 9 |
159 |
> bDescriptorType 2 |
160 |
> wTotalLength 25 |
161 |
> bNumInterfaces 1 |
162 |
> bConfigurationValue 1 |
163 |
> iConfiguration 0 |
164 |
> bmAttributes 0xe0 |
165 |
> Self Powered |
166 |
> Remote Wakeup |
167 |
> MaxPower 0mA |
168 |
> Interface Descriptor: |
169 |
> bLength 9 |
170 |
> bDescriptorType 4 |
171 |
> bInterfaceNumber 0 |
172 |
> bAlternateSetting 0 |
173 |
> bNumEndpoints 1 |
174 |
> bInterfaceClass 9 Hub |
175 |
> bInterfaceSubClass 0 Unused |
176 |
> bInterfaceProtocol 0 |
177 |
> iInterface 0 |
178 |
> Endpoint Descriptor: |
179 |
> bLength 7 |
180 |
> bDescriptorType 5 |
181 |
> bEndpointAddress 0x81 EP 1 IN |
182 |
> bmAttributes 3 |
183 |
> Transfer Type Interrupt |
184 |
> Synch Type None |
185 |
> Usage Type Data |
186 |
> wMaxPacketSize 0x0002 1x 2 bytes |
187 |
> bInterval 255 |
188 |
> Hub Descriptor: |
189 |
> bLength 9 |
190 |
> bDescriptorType 41 |
191 |
> nNbrPorts 2 |
192 |
> wHubCharacteristic 0x000a |
193 |
> No power switching (usb 1.0) |
194 |
> Per-port overcurrent protection |
195 |
> bPwrOn2PwrGood 1 * 2 milli seconds |
196 |
> bHubContrCurrent 0 milli Ampere |
197 |
> DeviceRemovable 0x00 |
198 |
> PortPwrCtrlMask 0xff |
199 |
> Hub Port Status: |
200 |
> Port 1: 0000.0303 lowspeed power enable connect |
201 |
> Port 2: 0000.0100 power |
202 |
> Device Status: 0x0003 |
203 |
> Self Powered |
204 |
> Remote Wakeup Enabled |
205 |
> |
206 |
> |
207 |
> Kernel-Config: |
208 |
> # cat .config | egrep "HID|USB" |
209 |
> # USB Network Adapters |
210 |
> # CONFIG_USB_CATC is not set |
211 |
> # CONFIG_USB_KAWETH is not set |
212 |
> # CONFIG_USB_PEGASUS is not set |
213 |
> # CONFIG_USB_RTL8150 is not set |
214 |
> # CONFIG_USB_USBNET_MII is not set |
215 |
> # CONFIG_USB_USBNET is not set |
216 |
> # USB-based Watchdog Cards |
217 |
> # CONFIG_USBPCWATCHDOG is not set |
218 |
> # CONFIG_I2C_TINY_USB is not set |
219 |
> CONFIG_V4L_USB_DRIVERS=y |
220 |
> # CONFIG_VIDEO_PVRUSB2 is not set |
221 |
> # CONFIG_VIDEO_USBVISION is not set |
222 |
> # CONFIG_USB_VICAM is not set |
223 |
> # CONFIG_USB_IBMCAM is not set |
224 |
> # CONFIG_USB_KONICAWC is not set |
225 |
> # CONFIG_USB_QUICKCAM_MESSENGER is not set |
226 |
> # CONFIG_USB_ET61X251 is not set |
227 |
> # CONFIG_USB_W9968CF is not set |
228 |
> # CONFIG_USB_OV511 is not set |
229 |
> # CONFIG_USB_SE401 is not set |
230 |
> # CONFIG_USB_SN9C102 is not set |
231 |
> # CONFIG_USB_STV680 is not set |
232 |
> # CONFIG_USB_ZC0301 is not set |
233 |
> # CONFIG_USB_PWC is not set |
234 |
> # CONFIG_USB_ZR364XX is not set |
235 |
> # CONFIG_USB_DSBR is not set |
236 |
> # Supported USB Adapters |
237 |
> # CONFIG_DVB_USB is not set |
238 |
> # CONFIG_DVB_TTUSB_BUDGET is not set |
239 |
> # CONFIG_DVB_TTUSB_DEC is not set |
240 |
> # USB devices |
241 |
> CONFIG_SND_USB_AUDIO=m |
242 |
> # CONFIG_SND_USB_USX2Y is not set |
243 |
> # CONFIG_SND_USB_CAIAQ is not set |
244 |
> # HID Devices |
245 |
> CONFIG_HID=y |
246 |
> # CONFIG_HID_DEBUG is not set |
247 |
> # USB Input Devices |
248 |
> CONFIG_USB_HID=y |
249 |
> CONFIG_USB_HIDINPUT_POWERBOOK=y |
250 |
> CONFIG_HID_FF=y |
251 |
> CONFIG_HID_PID=y |
252 |
> CONFIG_USB_HIDDEV=y |
253 |
> # USB support |
254 |
> CONFIG_USB_ARCH_HAS_HCD=y |
255 |
> CONFIG_USB_ARCH_HAS_OHCI=y |
256 |
> CONFIG_USB_ARCH_HAS_EHCI=y |
257 |
> CONFIG_USB=y |
258 |
> # CONFIG_USB_DEBUG is not set |
259 |
> # Miscellaneous USB options |
260 |
> CONFIG_USB_DEVICEFS=y |
261 |
> # CONFIG_USB_DEVICE_CLASS is not set |
262 |
> # CONFIG_USB_DYNAMIC_MINORS is not set |
263 |
> # CONFIG_USB_SUSPEND is not set |
264 |
> # CONFIG_USB_OTG is not set |
265 |
> # USB Host Controller Drivers |
266 |
> CONFIG_USB_EHCI_HCD=y |
267 |
> CONFIG_USB_EHCI_SPLIT_ISO=y |
268 |
> CONFIG_USB_EHCI_ROOT_HUB_TT=y |
269 |
> CONFIG_USB_EHCI_TT_NEWSCHED=y |
270 |
> # CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set |
271 |
> # CONFIG_USB_ISP116X_HCD is not set |
272 |
> # CONFIG_USB_OHCI_HCD is not set |
273 |
> CONFIG_USB_UHCI_HCD=y |
274 |
> # CONFIG_USB_SL811_HCD is not set |
275 |
> # USB Device Class drivers |
276 |
> # CONFIG_USB_ACM is not set |
277 |
> # CONFIG_USB_PRINTER is not set |
278 |
> # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' |
279 |
> # may also be needed; see USB_STORAGE Help for more information |
280 |
> CONFIG_USB_STORAGE=y |
281 |
> # CONFIG_USB_STORAGE_DEBUG is not set |
282 |
> CONFIG_USB_STORAGE_DATAFAB=y |
283 |
> CONFIG_USB_STORAGE_FREECOM=y |
284 |
> CONFIG_USB_STORAGE_ISD200=y |
285 |
> CONFIG_USB_STORAGE_DPCM=y |
286 |
> CONFIG_USB_STORAGE_USBAT=y |
287 |
> # CONFIG_USB_STORAGE_SDDR09 is not set |
288 |
> # CONFIG_USB_STORAGE_SDDR55 is not set |
289 |
> # CONFIG_USB_STORAGE_JUMPSHOT is not set |
290 |
> # CONFIG_USB_STORAGE_ALAUDA is not set |
291 |
> # CONFIG_USB_STORAGE_KARMA is not set |
292 |
> # CONFIG_USB_LIBUSUAL is not set |
293 |
> # USB Imaging devices |
294 |
> # CONFIG_USB_MDC800 is not set |
295 |
> # CONFIG_USB_MICROTEK is not set |
296 |
> CONFIG_USB_MON=y |
297 |
> # USB port drivers |
298 |
> # CONFIG_USB_USS720 is not set |
299 |
> # USB Serial Converter support |
300 |
> # CONFIG_USB_SERIAL is not set |
301 |
> # USB Miscellaneous drivers |
302 |
> # CONFIG_USB_EMI62 is not set |
303 |
> # CONFIG_USB_EMI26 is not set |
304 |
> # CONFIG_USB_ADUTUX is not set |
305 |
> # CONFIG_USB_AUERSWALD is not set |
306 |
> # CONFIG_USB_RIO500 is not set |
307 |
> # CONFIG_USB_LEGOTOWER is not set |
308 |
> # CONFIG_USB_LCD is not set |
309 |
> # CONFIG_USB_BERRY_CHARGE is not set |
310 |
> # CONFIG_USB_LED is not set |
311 |
> # CONFIG_USB_CYPRESS_CY7C63 is not set |
312 |
> # CONFIG_USB_CYTHERM is not set |
313 |
> # CONFIG_USB_PHIDGET is not set |
314 |
> # CONFIG_USB_IDMOUSE is not set |
315 |
> # CONFIG_USB_FTDI_ELAN is not set |
316 |
> # CONFIG_USB_APPLEDISPLAY is not set |
317 |
> # CONFIG_USB_SISUSBVGA is not set |
318 |
> # CONFIG_USB_LD is not set |
319 |
> # CONFIG_USB_TRANCEVIBRATOR is not set |
320 |
> # CONFIG_USB_IOWARRIOR is not set |
321 |
> # CONFIG_USB_TEST is not set |
322 |
> # USB DSL modem support |
323 |
> # USB Gadget Support |
324 |
> # CONFIG_USB_GADGET is not set |