| 1 |
Hallo an alle |
| 2 |
|
| 3 |
Ich bin nun soweit, dass mir der Kernel alle Devices erkennt. |
| 4 |
|
| 5 |
Nun habe ich jedoch ein IRQ Problem und er deaktiviert die Drives wieder. |
| 6 |
|
| 7 |
nitro-2.6.9-rc4-r2: |
| 8 |
|
| 9 |
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 |
| 10 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
| 11 |
ICH5: IDE controller at PCI slot 0000:00:1f.1 |
| 12 |
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) |
| 13 |
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11 |
| 14 |
ICH5: chipset revision 2 |
| 15 |
ICH5: 100% native mode on irq 11 |
| 16 |
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA |
| 17 |
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:DMA |
| 18 |
Probing IDE interface ide0... |
| 19 |
hda: MAXTOR 6L060J3, ATA DISK drive |
| 20 |
hdb: Maxtor 53073U6, ATA DISK drive |
| 21 |
ide0 at 0xc800-0xc807,0xc402 on irq 11 |
| 22 |
Probing IDE interface ide1... |
| 23 |
hdc: LITE-ON DVDRW SOHW-1213S, ATAPI CD/DVD-ROM drive |
| 24 |
hdd: TSSTcorpDVD-ROM TS-H352A, ATAPI CD/DVD-ROM drive |
| 25 |
irq 11: nobody cared! |
| 26 |
[<b0107b52>] __report_bad_irq+0x2a/0x8b |
| 27 |
[<b0107c3c>] note_interrupt+0x6f/0x9f |
| 28 |
[<b0107e2c>] do_IRQ+0xdd/0xdf |
| 29 |
[<b0105fd8>] common_interrupt+0x18/0x20 |
| 30 |
[<b011ce3b>] __do_softirq+0x2f/0x87 |
| 31 |
[<b011ceb9>] do_softirq+0x26/0x28 |
| 32 |
[<b0107e13>] do_IRQ+0xc4/0xdf |
| 33 |
[<b0105fd8>] common_interrupt+0x18/0x20 |
| 34 |
[<b012007b>] del_timer+0x25/0x58 |
| 35 |
[<b0107cf3>] enable_irq+0x35/0x91 |
| 36 |
[<b032de66>] probe_hwif+0x270/0x542 |
| 37 |
[<b0328923>] ata_attach+0x77/0xcd |
| 38 |
[<b032e14f>] probe_hwif_init+0x17/0x60 |
| 39 |
[<b033122b>] ide_setup_pci_device+0x7c/0x89 |
| 40 |
[<b032693d>] piix_init_one+0x1e/0x24 |
| 41 |
[<b053c8f2>] ide_scan_pcidev+0x59/0x6b |
| 42 |
[<b053c942>] ide_scan_pcibus+0x3e/0xab |
| 43 |
[<b053c822>] probe_for_hwifs+0x10/0x14 |
| 44 |
[<b053c884>] ide_init+0x5e/0x73 |
| 45 |
[<b052673b>] do_initcalls+0x28/0xb4 |
| 46 |
[<b053eaf0>] sock_init+0x3f/0x48 |
| 47 |
[<b0100406>] init+0x0/0x102 |
| 48 |
[<b0100434>] init+0x2e/0x102 |
| 49 |
[<b0104258>] kernel_thread_helper+0x0/0xb |
| 50 |
[<b010425d>] kernel_thread_helper+0x5/0xb |
| 51 |
handlers: |
| 52 |
[<b032b07d>] (ide_intr+0x0/0x12a) |
| 53 |
Disabling IRQ #11 |
| 54 |
ide1 at 0xc000-0xc007,0xbc02 on irq 11 |
| 55 |
libata version 1.02 loaded. |
| 56 |
ata_piix version 1.02 |
| 57 |
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 11 (level, low) -> IRQ 11 |
| 58 |
PCI: Setting latency timer of device 0000:00:1f.2 to 64 |
| 59 |
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 11 |
| 60 |
ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 11 |
| 61 |
ata1: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3c68 86:3c01 87:4003 |
| 62 |
88:20ff |
| 63 |
ata1: dev 0 ATA, max UDMA7, 156368016 sectors: lba48 |
| 64 |
ata1: dev 0 configured for UDMA/133 |
| 65 |
scsi0 : ata_piix |
| 66 |
ata2: SATA port has no device. |
| 67 |
scsi1 : ata_piix |
| 68 |
Vendor: ATA Model: SAMSUNG SP0812C Rev: SU10 |
| 69 |
Type: Direct-Access ANSI SCSI revision: 05 |
| 70 |
SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB) |
| 71 |
SCSI device sda: drive cache: write back |
| 72 |
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 |
| 73 |
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 |
| 74 |
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 |
| 75 |
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) |
| 76 |
USB Universal Host Controller Interface driver v2.2 |
| 77 |
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 10 (level, low) -> IRQ 10 |
| 78 |
|
| 79 |
Kann mir da jemand weiterhelfen. Ich verlier langsam die Geduld.... |
| 80 |
|
| 81 |
Vielen Dank und Grüsse Cyrill |
| 82 |
|
| 83 |
-- |
| 84 |
gentoo-user-de@g.o mailing list |
Archives