| 1 |
Hallo, |
| 2 |
|
| 3 |
Seit längerer Zeit plagt mich das Problem, dass mein einer |
| 4 |
USB-Port (Bus 5) stockend arbeitet. Egal, was für eine Peripherie ich |
| 5 |
dran hab'. Unter Windows kann ich das Phänomen, genauso wie an dem |
| 6 |
zweiten Port (Bus 4), nicht beobachten. Damit schließe ich einen |
| 7 |
Defekt der Hardware aus. |
| 8 |
Das "stocken" kommt meistens erst nach einiger Zeit, setzt manchmal |
| 9 |
wieder aus, usw. : |
| 10 |
|
| 11 |
# lsusb |
| 12 |
Bus 001 Device 001: ID 0000:0000 |
| 13 |
Bus 005 Device 002: ID 046d:c016 Logitech, Inc. M-UV69a Optical Wheel |
| 14 |
Mouse |
| 15 |
Bus 005 Device 001: ID 0000:0000 |
| 16 |
Bus 004 Device 002: ID 0ccd:0013 TerraTec Electronic GmbH |
| 17 |
Bus 004 Device 001: ID 0000:0000 |
| 18 |
Bus 003 Device 001: ID 0000:0000 |
| 19 |
Bus 002 Device 001: ID 0000:0000 |
| 20 |
|
| 21 |
#dmesg Zeigt nichts an Veränderungen an |
| 22 |
|
| 23 |
(Weitere Ausgaben weiter unten) |
| 24 |
|
| 25 |
Ich hoffe, ihr könnt mir zur weiteren Fehleranalyse, oder -bewältigung |
| 26 |
behilflich sein. |
| 27 |
|
| 28 |
MfG, |
| 29 |
Jan |
| 30 |
|
| 31 |
|
| 32 |
|
| 33 |
|
| 34 |
|
| 35 |
|
| 36 |
#lspci (gekürzt) |
| 37 |
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI |
| 38 |
Controller #1 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu Siemens |
| 39 |
Computer GmbH Unknown device 10b0 Flags: bus master, medium devsel, |
| 40 |
latency 0, IRQ 5 I/O ports at 1800 [size=32] |
| 41 |
|
| 42 |
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI |
| 43 |
Controller #2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu Siemens |
| 44 |
Computer GmbH Unknown device 10b0 Flags: bus master, medium devsel, |
| 45 |
latency 0, IRQ 11 I/O ports at 1820 [size=32] |
| 46 |
|
| 47 |
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI |
| 48 |
Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu Siemens |
| 49 |
Computer GmbH Unknown device 10b0 Flags: bus master, medium devsel, |
| 50 |
latency 0, IRQ 3 I/O ports at 1840 [size=32] |
| 51 |
|
| 52 |
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI |
| 53 |
Controller #4 (rev 02) (prog-if 00 [UHCI]) Subsystem: Fujitsu Siemens |
| 54 |
Computer GmbH Unknown device 10b0 Flags: bus master, medium devsel, |
| 55 |
latency 0, IRQ 10 I/O ports at 1860 [size=32] |
| 56 |
|
| 57 |
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 |
| 58 |
EHCI Controller (rev 02) (prog-if 20 [EHCI]) Subsystem: Fujitsu Siemens |
| 59 |
Computer GmbH Unknown device 10b0 Flags: bus master, medium devsel, |
| 60 |
latency 0, IRQ 5 Memory at b0004000 (32-bit, non-prefetchable) [size=1K] |
| 61 |
Capabilities: [50] Power Management version 2 |
| 62 |
Capabilities: [58] Debug port |
| 63 |
|
| 64 |
|
| 65 |
#lsusb -v (vom Bus 005) |
| 66 |
Bus 005 Device 002: ID 046d:c016 Logitech, Inc. M-UV69a Optical Wheel |
| 67 |
Mouse Device Descriptor: |
| 68 |
bLength 18 |
| 69 |
bDescriptorType 1 |
| 70 |
bcdUSB 2.00 |
| 71 |
bDeviceClass 0 (Defined at Interface level) |
| 72 |
bDeviceSubClass 0 |
| 73 |
bDeviceProtocol 0 |
| 74 |
bMaxPacketSize0 8 |
| 75 |
idVendor 0x046d Logitech, Inc. |
| 76 |
idProduct 0xc016 M-UV69a Optical Wheel Mouse |
| 77 |
bcdDevice 3.40 |
| 78 |
iManufacturer 1 Logitech |
| 79 |
iProduct 2 Optical USB Mouse |
| 80 |
iSerial 0 |
| 81 |
bNumConfigurations 1 |
| 82 |
Configuration Descriptor: |
| 83 |
bLength 9 |
| 84 |
bDescriptorType 2 |
| 85 |
wTotalLength 34 |
| 86 |
bNumInterfaces 1 |
| 87 |
bConfigurationValue 1 |
| 88 |
iConfiguration 0 |
| 89 |
bmAttributes 0xa0 |
| 90 |
(Bus Powered) |
| 91 |
Remote Wakeup |
| 92 |
MaxPower 100mA |
| 93 |
Interface Descriptor: |
| 94 |
bLength 9 |
| 95 |
bDescriptorType 4 |
| 96 |
bInterfaceNumber 0 |
| 97 |
bAlternateSetting 0 |
| 98 |
bNumEndpoints 1 |
| 99 |
bInterfaceClass 3 Human Interface Devices |
| 100 |
bInterfaceSubClass 1 Boot Interface Subclass |
| 101 |
bInterfaceProtocol 2 Mouse |
| 102 |
iInterface 0 |
| 103 |
HID Device Descriptor: |
| 104 |
bLength 9 |
| 105 |
bDescriptorType 33 |
| 106 |
bcdHID 1.10 |
| 107 |
bCountryCode 0 Not supported |
| 108 |
bNumDescriptors 1 |
| 109 |
bDescriptorType 34 Report |
| 110 |
wDescriptorLength 52 |
| 111 |
Report Descriptors: |
| 112 |
** UNAVAILABLE ** |
| 113 |
Endpoint Descriptor: |
| 114 |
bLength 7 |
| 115 |
bDescriptorType 5 |
| 116 |
bEndpointAddress 0x81 EP 1 IN |
| 117 |
bmAttributes 3 |
| 118 |
Transfer Type Interrupt |
| 119 |
Synch Type None |
| 120 |
Usage Type Data |
| 121 |
wMaxPacketSize 0x0004 1x 4 bytes |
| 122 |
bInterval 10 |
| 123 |
Device Status: 0x0000 |
| 124 |
(Bus Powered) |
| 125 |
|
| 126 |
Bus 005 Device 001: ID 0000:0000 |
| 127 |
Device Descriptor: |
| 128 |
bLength 18 |
| 129 |
bDescriptorType 1 |
| 130 |
bcdUSB 1.10 |
| 131 |
bDeviceClass 9 Hub |
| 132 |
bDeviceSubClass 0 Unused |
| 133 |
bDeviceProtocol 0 |
| 134 |
bMaxPacketSize0 64 |
| 135 |
idVendor 0x0000 |
| 136 |
idProduct 0x0000 |
| 137 |
bcdDevice 2.06 |
| 138 |
iManufacturer 3 Linux 2.6.22-gentoo-r9 uhci_hcd |
| 139 |
iProduct 2 UHCI Host Controller |
| 140 |
iSerial 1 0000:00:1d.3 |
| 141 |
bNumConfigurations 1 |
| 142 |
Configuration Descriptor: |
| 143 |
bLength 9 |
| 144 |
bDescriptorType 2 |
| 145 |
wTotalLength 25 |
| 146 |
bNumInterfaces 1 |
| 147 |
bConfigurationValue 1 |
| 148 |
iConfiguration 0 |
| 149 |
bmAttributes 0xe0 |
| 150 |
Self Powered |
| 151 |
Remote Wakeup |
| 152 |
MaxPower 0mA |
| 153 |
Interface Descriptor: |
| 154 |
bLength 9 |
| 155 |
bDescriptorType 4 |
| 156 |
bInterfaceNumber 0 |
| 157 |
bAlternateSetting 0 |
| 158 |
bNumEndpoints 1 |
| 159 |
bInterfaceClass 9 Hub |
| 160 |
bInterfaceSubClass 0 Unused |
| 161 |
bInterfaceProtocol 0 |
| 162 |
iInterface 0 |
| 163 |
Endpoint Descriptor: |
| 164 |
bLength 7 |
| 165 |
bDescriptorType 5 |
| 166 |
bEndpointAddress 0x81 EP 1 IN |
| 167 |
bmAttributes 3 |
| 168 |
Transfer Type Interrupt |
| 169 |
Synch Type None |
| 170 |
Usage Type Data |
| 171 |
wMaxPacketSize 0x0002 1x 2 bytes |
| 172 |
bInterval 255 |
| 173 |
Hub Descriptor: |
| 174 |
bLength 9 |
| 175 |
bDescriptorType 41 |
| 176 |
nNbrPorts 2 |
| 177 |
wHubCharacteristic 0x000a |
| 178 |
No power switching (usb 1.0) |
| 179 |
Per-port overcurrent protection |
| 180 |
bPwrOn2PwrGood 1 * 2 milli seconds |
| 181 |
bHubContrCurrent 0 milli Ampere |
| 182 |
DeviceRemovable 0x00 |
| 183 |
PortPwrCtrlMask 0xff |
| 184 |
Hub Port Status: |
| 185 |
Port 1: 0000.0303 lowspeed power enable connect |
| 186 |
Port 2: 0000.0100 power |
| 187 |
Device Status: 0x0003 |
| 188 |
Self Powered |
| 189 |
Remote Wakeup Enabled |
| 190 |
|
| 191 |
|
| 192 |
Kernel-Config: |
| 193 |
# cat .config | egrep "HID|USB" |
| 194 |
# USB Network Adapters |
| 195 |
# CONFIG_USB_CATC is not set |
| 196 |
# CONFIG_USB_KAWETH is not set |
| 197 |
# CONFIG_USB_PEGASUS is not set |
| 198 |
# CONFIG_USB_RTL8150 is not set |
| 199 |
# CONFIG_USB_USBNET_MII is not set |
| 200 |
# CONFIG_USB_USBNET is not set |
| 201 |
# USB-based Watchdog Cards |
| 202 |
# CONFIG_USBPCWATCHDOG is not set |
| 203 |
# CONFIG_I2C_TINY_USB is not set |
| 204 |
CONFIG_V4L_USB_DRIVERS=y |
| 205 |
# CONFIG_VIDEO_PVRUSB2 is not set |
| 206 |
# CONFIG_VIDEO_USBVISION is not set |
| 207 |
# CONFIG_USB_VICAM is not set |
| 208 |
# CONFIG_USB_IBMCAM is not set |
| 209 |
# CONFIG_USB_KONICAWC is not set |
| 210 |
# CONFIG_USB_QUICKCAM_MESSENGER is not set |
| 211 |
# CONFIG_USB_ET61X251 is not set |
| 212 |
# CONFIG_USB_W9968CF is not set |
| 213 |
# CONFIG_USB_OV511 is not set |
| 214 |
# CONFIG_USB_SE401 is not set |
| 215 |
# CONFIG_USB_SN9C102 is not set |
| 216 |
# CONFIG_USB_STV680 is not set |
| 217 |
# CONFIG_USB_ZC0301 is not set |
| 218 |
# CONFIG_USB_PWC is not set |
| 219 |
# CONFIG_USB_ZR364XX is not set |
| 220 |
# CONFIG_USB_DSBR is not set |
| 221 |
# Supported USB Adapters |
| 222 |
# CONFIG_DVB_USB is not set |
| 223 |
# CONFIG_DVB_TTUSB_BUDGET is not set |
| 224 |
# CONFIG_DVB_TTUSB_DEC is not set |
| 225 |
# USB devices |
| 226 |
CONFIG_SND_USB_AUDIO=m |
| 227 |
# CONFIG_SND_USB_USX2Y is not set |
| 228 |
# CONFIG_SND_USB_CAIAQ is not set |
| 229 |
# HID Devices |
| 230 |
CONFIG_HID=y |
| 231 |
# CONFIG_HID_DEBUG is not set |
| 232 |
# USB Input Devices |
| 233 |
CONFIG_USB_HID=y |
| 234 |
CONFIG_USB_HIDINPUT_POWERBOOK=y |
| 235 |
CONFIG_HID_FF=y |
| 236 |
CONFIG_HID_PID=y |
| 237 |
CONFIG_USB_HIDDEV=y |
| 238 |
# USB support |
| 239 |
CONFIG_USB_ARCH_HAS_HCD=y |
| 240 |
CONFIG_USB_ARCH_HAS_OHCI=y |
| 241 |
CONFIG_USB_ARCH_HAS_EHCI=y |
| 242 |
CONFIG_USB=y |
| 243 |
# CONFIG_USB_DEBUG is not set |
| 244 |
# Miscellaneous USB options |
| 245 |
CONFIG_USB_DEVICEFS=y |
| 246 |
# CONFIG_USB_DEVICE_CLASS is not set |
| 247 |
# CONFIG_USB_DYNAMIC_MINORS is not set |
| 248 |
# CONFIG_USB_SUSPEND is not set |
| 249 |
# CONFIG_USB_OTG is not set |
| 250 |
# USB Host Controller Drivers |
| 251 |
CONFIG_USB_EHCI_HCD=y |
| 252 |
CONFIG_USB_EHCI_SPLIT_ISO=y |
| 253 |
CONFIG_USB_EHCI_ROOT_HUB_TT=y |
| 254 |
CONFIG_USB_EHCI_TT_NEWSCHED=y |
| 255 |
# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set |
| 256 |
# CONFIG_USB_ISP116X_HCD is not set |
| 257 |
# CONFIG_USB_OHCI_HCD is not set |
| 258 |
CONFIG_USB_UHCI_HCD=y |
| 259 |
# CONFIG_USB_SL811_HCD is not set |
| 260 |
# USB Device Class drivers |
| 261 |
# CONFIG_USB_ACM is not set |
| 262 |
# CONFIG_USB_PRINTER is not set |
| 263 |
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' |
| 264 |
# may also be needed; see USB_STORAGE Help for more information |
| 265 |
CONFIG_USB_STORAGE=y |
| 266 |
# CONFIG_USB_STORAGE_DEBUG is not set |
| 267 |
CONFIG_USB_STORAGE_DATAFAB=y |
| 268 |
CONFIG_USB_STORAGE_FREECOM=y |
| 269 |
CONFIG_USB_STORAGE_ISD200=y |
| 270 |
CONFIG_USB_STORAGE_DPCM=y |
| 271 |
CONFIG_USB_STORAGE_USBAT=y |
| 272 |
# CONFIG_USB_STORAGE_SDDR09 is not set |
| 273 |
# CONFIG_USB_STORAGE_SDDR55 is not set |
| 274 |
# CONFIG_USB_STORAGE_JUMPSHOT is not set |
| 275 |
# CONFIG_USB_STORAGE_ALAUDA is not set |
| 276 |
# CONFIG_USB_STORAGE_KARMA is not set |
| 277 |
# CONFIG_USB_LIBUSUAL is not set |
| 278 |
# USB Imaging devices |
| 279 |
# CONFIG_USB_MDC800 is not set |
| 280 |
# CONFIG_USB_MICROTEK is not set |
| 281 |
CONFIG_USB_MON=y |
| 282 |
# USB port drivers |
| 283 |
# CONFIG_USB_USS720 is not set |
| 284 |
# USB Serial Converter support |
| 285 |
# CONFIG_USB_SERIAL is not set |
| 286 |
# USB Miscellaneous drivers |
| 287 |
# CONFIG_USB_EMI62 is not set |
| 288 |
# CONFIG_USB_EMI26 is not set |
| 289 |
# CONFIG_USB_ADUTUX is not set |
| 290 |
# CONFIG_USB_AUERSWALD is not set |
| 291 |
# CONFIG_USB_RIO500 is not set |
| 292 |
# CONFIG_USB_LEGOTOWER is not set |
| 293 |
# CONFIG_USB_LCD is not set |
| 294 |
# CONFIG_USB_BERRY_CHARGE is not set |
| 295 |
# CONFIG_USB_LED is not set |
| 296 |
# CONFIG_USB_CYPRESS_CY7C63 is not set |
| 297 |
# CONFIG_USB_CYTHERM is not set |
| 298 |
# CONFIG_USB_PHIDGET is not set |
| 299 |
# CONFIG_USB_IDMOUSE is not set |
| 300 |
# CONFIG_USB_FTDI_ELAN is not set |
| 301 |
# CONFIG_USB_APPLEDISPLAY is not set |
| 302 |
# CONFIG_USB_SISUSBVGA is not set |
| 303 |
# CONFIG_USB_LD is not set |
| 304 |
# CONFIG_USB_TRANCEVIBRATOR is not set |
| 305 |
# CONFIG_USB_IOWARRIOR is not set |
| 306 |
# CONFIG_USB_TEST is not set |
| 307 |
# USB DSL modem support |
| 308 |
# USB Gadget Support |
| 309 |
# CONFIG_USB_GADGET is not set |
Archives