| 1 |
Hallo, |
| 2 |
|
| 3 |
habe eine Avermedia 771 DVB-T Karte eingebaut. Dazu kernel 2.6.10-rc2 von |
| 4 |
kernel.org installiert. |
| 5 |
|
| 6 |
Habe viele howtos gelesen und komme dennoch nicht weiter. Ich verstehe das |
| 7 |
mit dem patchen und den dvb-t-kernel-cvs-checkout nicht so ganz.... brauch |
| 8 |
ich die überhaupt? Ich habe zumindest bis auf den Kernel nichts weiter |
| 9 |
installiert. |
| 10 |
|
| 11 |
Folgendes gebe ich ein: |
| 12 |
|
| 13 |
Code: |
| 14 |
modprobe bttv |
| 15 |
|
| 16 |
|
| 17 |
Und hier die Ausgabe von dmesg: |
| 18 |
|
| 19 |
Code: |
| 20 |
Linux video capture interface: v1.00 |
| 21 |
bttv: driver version 0.9.15 loaded |
| 22 |
bttv: using 8 buffers with 2080k (520 pages) each for capture |
| 23 |
bttv: Bt8xx card found (0). |
| 24 |
PCI: Found IRQ 11 for device 0000:00:0c.0 |
| 25 |
PCI: Sharing IRQ 11 with 0000:00:0a.0 |
| 26 |
PCI: Sharing IRQ 11 with 0000:00:0c.1 |
| 27 |
PCI: Sharing IRQ 11 with 0000:00:10.2 |
| 28 |
bttv0: Bt878 (rev 17) at 0000:00:0c.0, irq: 11, latency: 32, mmio: |
| 29 |
0xeb002000 |
| 30 |
bttv0: detected: AVermedia DVB-T 771 [card=123], PCI subsystem ID is |
| 31 |
1461:0771 |
| 32 |
bttv0: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected] |
| 33 |
bttv0: gpio: en=00000000, out=00000000 in=00f0ff0f [init] |
| 34 |
i2c_adapter i2c-0: registered as adapter #0 |
| 35 |
bttv0: using tuner=4 |
| 36 |
i2c-core: driver i2c TV tuner driver registered. |
| 37 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0060 |
| 38 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 39 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0061 |
| 40 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 41 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0062 |
| 42 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 43 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0063 |
| 44 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 45 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0064 |
| 46 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 47 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0065 |
| 48 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 49 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0066 |
| 50 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 51 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0067 |
| 52 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 53 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0068 |
| 54 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 55 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 0069 |
| 56 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 57 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 006a |
| 58 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 59 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 006b |
| 60 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 61 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 006c |
| 62 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 63 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 006d |
| 64 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 65 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 006e |
| 66 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 67 |
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr 006f |
| 68 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 69 |
bttv0: registered device video0 |
| 70 |
bttv0: registered device vbi0 |
| 71 |
bttv0: PLL: 28636363 => 35468950 .. ok |
| 72 |
bttv0: add subdevice "remote0" |
| 73 |
bttv0: add subdevice "dvb0" |
| 74 |
|
| 75 |
|
| 76 |
Code: |
| 77 |
modprobe mt352 |
| 78 |
|
| 79 |
|
| 80 |
Und hier die Ausgabe von dmesg: |
| 81 |
|
| 82 |
Code: |
| 83 |
i2c-core: driver dvbfe_mt352 registered. |
| 84 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 85 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 86 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 87 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 88 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 89 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 90 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 91 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 92 |
i2c_adapter i2c-0: master_xfer: with 2 msgs. |
| 93 |
dvbfe_mt352: Setup for AverMedia DVB-T 771 |
| 94 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 95 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 96 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 97 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 98 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 99 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 100 |
i2c_adapter i2c-0: master_xfer: with 1 msgs. |
| 101 |
i2c_adapter i2c-0: client [dvbfe_mt352] registered to adapter |
| 102 |
registering 0-0000 |
| 103 |
|
| 104 |
|
| 105 |
Code: |
| 106 |
modprobe dvb-bt8xx |
| 107 |
|
| 108 |
|
| 109 |
Und hier die Ausgabe von dmesg: |
| 110 |
|
| 111 |
Code: |
| 112 |
bt878: AUDIO driver version 0.0.0 loaded |
| 113 |
bt878: Bt878 AUDIO function found (0). |
| 114 |
PCI: Found IRQ 11 for device 0000:00:0c.1 |
| 115 |
PCI: Sharing IRQ 11 with 0000:00:0a.0 |
| 116 |
PCI: Sharing IRQ 11 with 0000:00:0c.0 |
| 117 |
PCI: Sharing IRQ 11 with 0000:00:10.2 |
| 118 |
bt878(0): Bt878 (rev 17) at 00:0c.1, irq: 11, latency: 32, memory: |
| 119 |
0xeb003000 |
| 120 |
DVB: registering new adapter (bttv0). |
| 121 |
|
| 122 |
|
| 123 |
|
| 124 |
|
| 125 |
Wie geht es nun weiter? Wie ich inzwischen las, kann tvtime nicht verwendet |
| 126 |
werden. |
| 127 |
|
| 128 |
|
| 129 |
|
| 130 |
Grüße |
| 131 |
Holger |
| 132 |
|
| 133 |
|
| 134 |
-- |
| 135 |
gentoo-user-de@g.o mailing list |
Archives