1 |
Am Samstag, 25. September 2004, 11:55:29, Daniel Rindt hast Du geschrieben: |
2 |
|
3 |
> Hallo, |
4 |
|
5 |
> Ich habe nach HOWTO entsprechend ein UML System erstellt. Leider bootet es |
6 |
> nicht richtig: |
7 |
> === |
8 |
> radium uml # linux ubd0=root_fs ubd1=swap_fs |
9 |
> Checking for the skas3 patch in the host...not found |
10 |
> Checking for /proc/mm...not found |
11 |
> tracing thread pid = 9859 |
12 |
> Checking for /dev/anon on the host...Not available (open failed with errno |
13 |
> 2) |
14 |
> Checking for /dev/anon on the host...Not available (open failed with errno |
15 |
> 2) |
16 |
> Checking for /dev/anon on the host...Not available (open failed with errno |
17 |
> 2) |
18 |
> Checking for /dev/anon on the host...Not available (open failed with errno |
19 |
> 2) |
20 |
> Linux version 2.4.24-uml1-r9 (root@radium) (gcc version 3.3.4 20040623 |
21 |
> (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #1 Sun Sep 19 18:04:27 CEST |
22 |
> 2004 |
23 |
> On node 0 totalpages: 8192 |
24 |
> zone(0): 8192 pages. |
25 |
> zone(1): 0 pages. |
26 |
> zone(2): 0 pages. |
27 |
> Kernel command line: ubd0=root_fs ubd1=swap_fs root=/dev/ubd0 |
28 |
> Calibrating delay loop... 1189.47 BogoMIPS |
29 |
> Memory: 28860k available |
30 |
> Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) |
31 |
> Inode cache hash table entries: 2048 (order: 2, 16384 bytes) |
32 |
> Mount cache hash table entries: 512 (order: 0, 4096 bytes) |
33 |
> Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) |
34 |
> Page-cache hash table entries: 8192 (order: 3, 32768 bytes) |
35 |
> Checking for host processor cmov support...Yes |
36 |
> Checking for host processor xmm support...No |
37 |
> Checking that ptrace can change system call numbers...OK |
38 |
> Checking that host ptys support output SIGIO...Yes |
39 |
> Checking that host ptys support SIGIO on close...No, enabling workaround |
40 |
> POSIX conformance testing by UNIFIX |
41 |
> Linux NET4.0 for Linux 2.4 |
42 |
> Based upon Swansea University Computer Society NET3.039 |
43 |
> Initializing RT netlink socket |
44 |
> Starting kswapd |
45 |
> VFS: Disk quotas vdquot_6.5.1 |
46 |
> devfs: v1.12c (20020818) Richard Gooch (rgooch@××××××××××.au) |
47 |
> devfs: boot_options: 0x1 |
48 |
> JFFS version 1.0, (C) 1999, 2000 Axis Communications AB |
49 |
> JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications |
50 |
> AB. |
51 |
> pty: 256 Unix98 ptys configured |
52 |
> SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). |
53 |
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize |
54 |
> loop: loaded (max 8 devices) |
55 |
> PPP generic driver version 2.4.2 |
56 |
> Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky |
57 |
> SCSI subsystem driver Revision: 1.00 |
58 |
> scsi0 : scsi_debug, Version: 0.61 (20020815), num_devs=1, dev_size_mb=8, |
59 |
> opts=0x0 |
60 |
> Vendor: Linux Model: scsi_debug Rev: 0004 |
61 |
> Type: Direct-Access ANSI SCSI revision: 03 |
62 |
> blkmtd: error: missing `device' name |
63 |
|
64 |
> Initializing software serial port version 1 |
65 |
> mconsole (version 2) initialized on /root/.uml/YMdLpg/mconsole |
66 |
> Partition check: |
67 |
> ubda: unknown partition table |
68 |
> ubdb: unknown partition table |
69 |
> UML Audio Relay (host dsp = /dev/sound/dsp, host mixer = /dev/sound/mixer) |
70 |
> Initializing stdio console driver |
71 |
> NET4: Linux TCP/IP 1.0 for NET4.0 |
72 |
> IP Protocols: ICMP, UDP, TCP |
73 |
> IP: routing cache hash table of 512 buckets, 4Kbytes |
74 |
> TCP: Hash tables configured (established 2048 bind 4096) |
75 |
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. |
76 |
> VFS: Mounted root (ext2 filesystem) readonly. |
77 |
> Mounted devfs on /dev |
78 |
> INIT: version 2.84 booting |
79 |
|
80 |
> Gentoo Linux; http://www.gentoo.org/ |
81 |
> Copyright 2001-2004 Gentoo Technologies, Inc.; Distributed under the GPL |
82 |
|
83 |
> * Mounting proc at /proc... [ ok ] |
84 |
> * Starting devfsd...Started device management daemon v1.3.25 for /dev |
85 |
> [ ok ] |
86 |
> * Activating (possible) swap...modprobe: Can't open dependencies file |
87 |
> /lib/modules/2.4.24-uml1-r9/modules.dep (No such file or directory) |
88 |
> [ ok ] |
89 |
> * Remounting root filesystem read-only (if necessary)... [ ok ] |
90 |
> * Checking root filesystem...ext2fs_check_if_mount: No such file or |
91 |
> directory while determining whether / is mounted. |
92 |
> fsck.ext2: Is a directory while trying to open / |
93 |
> /: |
94 |
|
95 |
Schreibe mal bitte dein UML Start Zeile. |
96 |
|
97 |
|
98 |
> Vielen Dank. |
99 |
> Daniel |
100 |
|
101 |
UML wurde ja hier schon des oeftern angesprochen. |
102 |
Viele Problem wurden schon damit geloest das als Grundlagen der |
103 |
UML-2.6 Kernel eingesetzt wurde. Ist ~x86, laueft bei mir aber |
104 |
problemlos. |
105 |
|
106 |
-- |
107 |
Gruss Joerg |
108 |
|
109 |
NEUER SCHLUESSEL !!! |
110 |
GPG-Key 0x34C2808A |
111 |
Fingerprint: 9591 AAA8 E8CC 1BCC 767D 3B1D 34C2 808A |