| 1 |
Bon alors voici en vrac : |
| 2 |
|
| 3 |
cat /etc/conf.d/net |
| 4 |
modules_wlan0=( "iwconfig" ) |
| 5 |
config_wlan0=( "dhcp" ) |
| 6 |
modules_wlan1=( "iwconfig" ) |
| 7 |
config_wlan1=( "dhcp" ) |
| 8 |
config_eth0=( "dhcp" ) |
| 9 |
dhcpcd_eth0="-t 10" |
| 10 |
|
| 11 |
|
| 12 |
cat /etc/conf.d/wireless |
| 13 |
essid_wlan0="hilson" |
| 14 |
essid_wlan1="hilson" |
| 15 |
|
| 16 |
|
| 17 |
(il faut savoir que avant, ndiswrapper me mettait la clé sur wlan0, |
| 18 |
puis ensuite, après un upgrade, il me l'a mise en wlan1, donc j'ai |
| 19 |
simplement copié-collé la config) |
| 20 |
|
| 21 |
(autre il faut savoir : mon wireless n'est pas sécurisé. NON ! Ne me |
| 22 |
frappez pas :-P ) |
| 23 |
|
| 24 |
|
| 25 |
tail /var/log/messages |
| 26 |
|
| 27 |
Feb 19 22:35:50 diva usb 1-3: new high speed USB device using ehci_hcd |
| 28 |
and address 3 |
| 29 |
Feb 19 22:35:50 diva usb 1-3: configuration #1 chosen from 1 choice |
| 30 |
Feb 19 22:36:25 diva ndiswrapper version 1.33 loaded (preempt=yes,smp=no) |
| 31 |
Feb 19 22:36:25 diva usb 1-3: reset high speed USB device using |
| 32 |
ehci_hcd and address 3 |
| 33 |
Feb 19 22:36:25 diva ndiswrapper: driver sis163u (Silicon Integrated |
| 34 |
Systems Corp.(1.02.01),10/28/2004,5.1.1039.1020) loaded |
| 35 |
Feb 19 22:36:26 diva wlan0: ethernet device 00:03:2f:2a:e3:12 using |
| 36 |
NDIS driver: sis163u, version: 0x1000000, NDIS version: 0x501, vendor: |
| 37 |
'Wireless Driver', 0D8E:0163.F.conf |
| 38 |
Feb 19 22:36:26 diva wlan0: encryption modes supported: WEP; TKIP with |
| 39 |
WPA; AES/CCMP with WPA |
| 40 |
Feb 19 22:36:26 diva usbcore: registered new driver ndiswrapper |
| 41 |
Feb 19 22:36:26 diva ndiswrapper: changing interface name from 'wlan0' |
| 42 |
to 'wlan1' |
| 43 |
Feb 19 22:36:28 diva dhcpcd[6302]: MAC address = 00:03:2f:2a:e3:12 |
| 44 |
Feb 19 22:36:28 diva dhcpcd[6302]: verified 192.168.1.100 address is not in use |
| 45 |
Feb 19 22:36:28 diva dhcpcd[6302]: your IP address = 192.168.1.100 |
| 46 |
|
| 47 |
(bizarre, on dirait qu'il la met sur wlan0 puis qu'il la switch sur wlan1...) |
| 48 |
|
| 49 |
iwconfig |
| 50 |
lo no wireless extensions. |
| 51 |
|
| 52 |
eth0 no wireless extensions. |
| 53 |
|
| 54 |
wlan1 IEEE 802.11FH ESSID:"hilson" |
| 55 |
Mode:Managed Frequency:2.437 GHz Access Point: 00:03:2F:2A:32:6C |
| 56 |
Bit Rate:48 Mb/s Tx-Power:24 dBm Sensitivity=0/3 |
| 57 |
RTS thr:-1 B Fragment thr:65535 B |
| 58 |
Encryption key:off |
| 59 |
Power Management:off |
| 60 |
Link Quality:9/100 Signal level:-90 dBm Noise level:-96 dBm |
| 61 |
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 |
| 62 |
Tx excessive retries:14 Invalid misc:111 Missed beacon:0 |
| 63 |
|
| 64 |
|
| 65 |
route -n |
| 66 |
Kernel IP routing table |
| 67 |
Destination Gateway Genmask Flags Metric Ref Use Iface |
| 68 |
192.168.1.0 0.0.0.0 255.255.255.0 U 2000 0 0 wlan1 |
| 69 |
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo |
| 70 |
0.0.0.0 192.168.1.1 0.0.0.0 UG 2000 0 0 wlan1 |
| 71 |
|
| 72 |
Vraiment tout a l'air nickel, mais quand je fais un ping 192.168.1.1, |
| 73 |
il me dit host unreachable. |
| 74 |
|
| 75 |
Et si je fais un /etc/init.d/wlan1 restart |
| 76 |
j'ai un dhcp timeout :-( |
| 77 |
|
| 78 |
-- |
| 79 |
(\__/) |
| 80 |
(='.'=) Ceci est un petit lapin. Copiez/collez-le dans |
| 81 |
(")_(") votre signature pour l'aider à dominer le monde |
| 82 |
-- |
| 83 |
gentoo-user-fr@g.o mailing list |
Archives