[gentoo-user-ru] Nokia 6021 & gprs

[Vladimir Rusinov]

Доброго времени суток!

Проблемы с подключением gprs через Nokia 6021:

При первой попытке подключения:

# wvdial
WvDial<*1>: WvDial: Internet dialer version 1.56
WvDial<*1>: Initializing modem.
WvDial<*1>: Sending: ATZ
WvDial Modem<*1>: ATZ
WvDial Modem<*1>: OK
WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
WvDial Modem<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
WvDial Modem<*1>: OK
WvDial<*1>: Sending: AT+CGDCONT=1,"IP","internet.mts.ru"
WvDial Modem<*1>: AT+CGDCONT=1,"IP","internet.mts.ru"
WvDial Modem<*1>: OK
WvDial<*1>: Modem initialized.
WvDial<*1>: Sending: ATDT*99#
WvDial<*1>: Waiting for carrier.
WvDial Modem<*1>: ATDT*99#
WvDial Modem<*1>: CONNECT
WvDial Modem<*1>: ~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
WvDial<*1>: Carrier detected.  Waiting for prompt.
WvDial<Err>: Connected, but carrier signal lost!  Retrying...
WvDial<*1>: Sending: ATDT*99#
WvDial<*1>: Waiting for carrier.
WvDial Modem<*1>: ~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} }
g}%~~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~~[7f]}#@!}!} }
}2}#}$@#}!}$}%\}"}&} }*} } g}%~~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*}
} g}%~~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~~[7f]}#@!}!} }
}2}#}$@#}!}$}%\}"}&} }*} } g}%~~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*}
} g}%~~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~~[7f]}#@!}!} }
}2}#}$@#}!}$}%\}"}&} }*} } g}%~
WvDial<Warn>: Timed out while dialing.  Trying again.
WvDial<*1>: Sending: ATDT*99#
WvDial<*1>: Waiting for carrier.
WvDial<Warn>: Timed out while dialing.  Trying again.
WvDial<*1>: Sending: ATDT*99#
< и т.д. >

При последующих - просто 'modem not responding'

# dmesg | tail
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead

# cat /etc/wvdial.conf

[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,"IP","internet.mts.ru"
Modem Type = Analog Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = mts
Password = mts
Baud = 230400

В чем может быть проблема?

-- 
Vladimir Rusinov
GreenMice Solutions: IT-решения на базе Linux
http://greenmice.info/