1 |
-----BEGIN PGP SIGNED MESSAGE----- |
2 |
Hash: SHA1 |
3 |
|
4 |
Hello! |
5 |
I try to setup a wireless card to my gentoo box, but I can't set it: |
6 |
the net is with a wpa-key (type tkip). The SSID is Super S and when I |
7 |
configure it so: |
8 |
#iwconfig wlan0 essid "my SSID" nick "Cinzia" key wep-key |
9 |
after that I read with iwconfig: |
10 |
# iwconfig wlan0 |
11 |
wlan0 IEEE 802.11b+/g+ ESSID:"my SSID" |
12 |
Mode:Managed Channel:1 Access Point: 00:00:80:F9:37:03 |
13 |
Bit Rate:268.501 Mb/s Tx-Power:268500993 Sensitivity:24937 |
14 |
Retry:on Fragment thr=256 B |
15 |
Encryption key:xxxx-xxxx-xxxx-xxxx-xxxx-xxxx-xx Security |
16 |
mode:restricted |
17 |
Power Management:on |
18 |
|
19 |
But if I do |
20 |
#dhcpd wlan0 |
21 |
the card doesn't try to contact the router (no log) and in dmesg: |
22 |
|
23 |
#dmesg |
24 |
updating initial settings on iface activation |
25 |
get_mask 0x00000000, set_mask 0x0006CEBC |
26 |
important setting has been changed. Need to update packet templates, too |
27 |
updating packet templates |
28 |
updating transmit power: 15 dBm |
29 |
updating antenna value: 0x4A |
30 |
updating Energy Detect (ED) threshold: 0 |
31 |
acx111 doesn't support ED! |
32 |
updating Channel Clear Assessment (CCA) value: 0x00 |
33 |
acx111 doesn't support CCA! |
34 |
updating channel to: 1 |
35 |
updating: enable Tx |
36 |
updating: enable Rx on channel: 1 |
37 |
updating regulatory domain: 0x30 |
38 |
updating WEP key settings |
39 |
setting WEP key: 0 with total size: 13 |
40 |
setting WEP key 0 as default |
41 |
acx_set_status(1):SCANNING |
42 |
starting radio scan |
43 |
get_mask 0x00000000, set_mask 0x00000000 - after update |
44 |
ADDRCONF(NETDEV_UP): wlan0: link is not ready |
45 |
acx_i_timer: adev->status=1 (SCANNING) |
46 |
continuing scan (1 sec) |
47 |
acx_i_timer: adev->status=1 (SCANNING) |
48 |
continuing scan (2 sec) |
49 |
acx_i_timer: adev->status=1 (SCANNING) |
50 |
continuing scan (3 sec) |
51 |
acx_i_timer: adev->status=1 (SCANNING) |
52 |
continuing scan (4 sec) |
53 |
acx_i_timer: adev->status=1 (SCANNING) |
54 |
continuing scan (5 sec) |
55 |
acx_i_timer: adev->status=1 (SCANNING) |
56 |
continuing scan (6 sec) |
57 |
acx_i_timer: adev->status=1 (SCANNING) |
58 |
stopping scan |
59 |
no matching station found in range yet |
60 |
acx_set_status(1):SCANNING |
61 |
starting radio scan |
62 |
rx: unsupported 802.11 protocol |
63 |
rx: unsupported 802.11 protocol |
64 |
acx_i_timer: adev->status=1 (SCANNING) |
65 |
continuing scan (1 sec) |
66 |
acx_i_timer: adev->status=1 (SCANNING) |
67 |
continuing scan (2 sec) |
68 |
acx_i_timer: adev->status=1 (SCANNING) |
69 |
continuing scan (3 sec) |
70 |
acx_i_timer: adev->status=1 (SCANNING) |
71 |
continuing scan (4 sec) |
72 |
acx_i_timer: adev->status=1 (SCANNING) |
73 |
continuing scan (5 sec) |
74 |
acx_i_timer: adev->status=1 (SCANNING) |
75 |
continuing scan (6 sec) |
76 |
acx_i_timer: adev->status=1 (SCANNING) |
77 |
stopping scan |
78 |
no matching station found in range yet |
79 |
acx_set_status(1):SCANNING |
80 |
starting radio scan |
81 |
rx: unsupported 802.11 protocol |
82 |
acx: truncated rx header (-1656 bytes)! |
83 |
|
84 |
rx: unsupported 802.11 protocol |
85 |
acx_i_timer: adev->status=1 (SCANNING) |
86 |
continuing scan (1 sec) |
87 |
acx_i_timer: adev->status=1 (SCANNING) |
88 |
continuing scan (2 sec) |
89 |
acx_i_timer: adev->status=1 (SCANNING) |
90 |
continuing scan (3 sec) |
91 |
acx_i_timer: adev->status=1 (SCANNING) |
92 |
continuing scan (4 sec) |
93 |
|
94 |
|
95 |
It is a card problem and a setup problem? The card uses experimental acx |
96 |
driver (it is a AVM Fritz! WLAN USB) |
97 |
Thanks a lot, |
98 |
Luigi |
99 |
- -- |
100 |
Public key GPG(0x633F86B7) on http://keyserver.linux.it/ |
101 |
-----BEGIN PGP SIGNATURE----- |
102 |
Version: GnuPG v1.4.2.2 (GNU/Linux) |
103 |
|
104 |
iD8DBQFEP/x+HmkkjmM/hrcRAtxDAJ0YMZxXmjQax5BMFAV49aaCaLrvTACfVKen |
105 |
D8O1UUSA0ctlJFUwiTdUmlA= |
106 |
=4cQv |
107 |
-----END PGP SIGNATURE----- |
108 |
-- |
109 |
gentoo-user@g.o mailing list |