1 |
Hi All, |
2 |
|
3 |
I've booted into a new kernel (2.6.18-gentoo-r2) and suddenly discovered more |
4 |
info than I had previously noticed in lspci regarding my video card: |
5 |
================================================== |
6 |
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY |
7 |
(prog-if 00 [VGA]) |
8 |
Subsystem: Compaq Computer Corporation Evo N600c |
9 |
Flags: bus master, stepping, 66MHz, medium devsel, latency 66, IRQ 11 |
10 |
Memory at 48000000 (32-bit, prefetchable) [size=128M] |
11 |
I/O ports at 3000 [size=256] |
12 |
Memory at 40200000 (32-bit, non-prefetchable) [size=64K] |
13 |
[virtual] Expansion ROM at 40220000 [disabled] [size=128K] |
14 |
Capabilities: [58] AGP version 2.0 |
15 |
Capabilities: [50] Power Management version 2 |
16 |
================================================== |
17 |
|
18 |
Anyway, I saw this line: |
19 |
|
20 |
[virtual] Expansion ROM at 40220000 [disabled] [size=128K] |
21 |
|
22 |
Why is it disabled? Could this be the reason that when in console I have no |
23 |
scroll back left in the framebuffer? Or that glxgears runs like a pig (in |
24 |
slow motion)? |
25 |
================================================== |
26 |
$ glxgears |
27 |
libGL warning: 3D driver claims to not support visual 0x4b |
28 |
2446 frames in 5.0 seconds = 489.111 FPS |
29 |
2441 frames in 5.0 seconds = 488.094 FPS |
30 |
2448 frames in 5.0 seconds = 489.509 FPS |
31 |
2438 frames in 5.0 seconds = 487.576 FPS |
32 |
2445 frames in 5.0 seconds = 488.976 FPS |
33 |
2442 frames in 5.0 seconds = 488.238 FPS |
34 |
2439 frames in 5.0 seconds = 487.720 FPS |
35 |
================================================== |
36 |
|
37 |
================================================== |
38 |
$ glxinfo |
39 |
name of display: :0.0 |
40 |
libGL warning: 3D driver claims to not support visual 0x4b |
41 |
display: :0 screen: 0 |
42 |
direct rendering: Yes |
43 |
================================================== |
44 |
|
45 |
While you're looking at this I would appreciate if you could tell me why I am |
46 |
getting this libGL warning (and how to fix it)? |
47 |
|
48 |
Finally, I am also getting this mtrr overlap at boot: |
49 |
================================================== |
50 |
mtrr: 0x48000000,0x8000000 overlaps existing 0x48000000,0x1000000 |
51 |
mtrr: 0x48000000,0x8000000 overlaps existing 0x48000000,0x1000000 |
52 |
mtrr: 0x48000000,0x8000000 overlaps existing 0x48000000,0x1000000 |
53 |
mtrr: 0x48000000,0x8000000 overlaps existing 0x48000000,0x1000000 |
54 |
mtrr: 0x48000000,0x8000000 overlaps existing 0x48000000,0x1000000 |
55 |
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. |
56 |
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode |
57 |
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode |
58 |
[drm] Setting GART location based on new memory map |
59 |
[drm] writeback test succeeded in 1 usecs |
60 |
================================================== |
61 |
|
62 |
Any suggestions for fixing any of the above would be much appreciated. :) |
63 |
-- |
64 |
Regards, |
65 |
Mick |