| 1 |
Bo Andresen <bo.andresen <at> gmail.com> writes: |
| 2 |
|
| 3 |
> |
| 4 |
> I have a laptop with a ATI Radeon 9000 Mobility graphics card. I wanted to get |
| 5 |
> 3d rendering working with the free dri drivers so I followed this howto: |
| 6 |
> http://www.gentoolinux.org/doc/en/dri-howto.xml |
| 7 |
|
| 8 |
Extremely cool! I tried some time ago, and gave up. If you are successful, drop |
| 9 |
me a line, with your final list of tricks that works: |
| 10 |
|
| 11 |
Here's my system: |
| 12 |
|
| 13 |
|
| 14 |
from lshw: |
| 15 |
*-display |
| 16 |
description: VGA compatible controller |
| 17 |
product: Radeon R250 Lf [FireGL 9000] |
| 18 |
vendor: ATI Technologies Inc |
| 19 |
physical id: 0 |
| 20 |
bus info: pci@01:00.0 |
| 21 |
version: 01 |
| 22 |
size: 128MB |
| 23 |
width: 32 bits |
| 24 |
clock: 66MHz |
| 25 |
capabilities: vga bus_master cap_list |
| 26 |
configuration: driver=radeonfb |
| 27 |
resources: iomemory:f0000000-f7ffffff ioport:9000-90ff iomemory: |
| 28 |
ec100000-ec10ffff irq:11 |
| 29 |
|
| 30 |
>From lspci: |
| 31 |
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf [FireGL |
| 32 |
9000] (rev 01) (prog-if 00 [VGA]) |
| 33 |
Subsystem: CLEVO/KAPOK Computer Unknown device 0402 |
| 34 |
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- |
| 35 |
Stepping+ SERR- FastB2B+ |
| 36 |
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- |
| 37 |
<TAbort- <MAbort- >SERR- <PERR- |
| 38 |
Latency: 66 (2000ns min), Cache Line Size 04 |
| 39 |
Interrupt: pin A routed to IRQ 11 |
| 40 |
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] |
| 41 |
Region 1: I/O ports at 9000 [size=256] |
| 42 |
Region 2: Memory at ec100000 (32-bit, non-prefetchable) [size=64K] |
| 43 |
[virtual] Expansion ROM at ec120000 [disabled] [size=128K] |
| 44 |
Capabilities: [58] AGP version 2.0 |
| 45 |
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- |
| 46 |
64bit- FW+ AGP3- Rate=x1,x2,x4 |
| 47 |
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> |
| 48 |
Capabilities: [50] Power Management version 2 |
| 49 |
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA |
| 50 |
PME(D0-,D1-,D2-,D3hot-,D3cold-) |
| 51 |
Status: D0 PME-Enable- DSel=0 DScale=0 PME- |
| 52 |
|
| 53 |
|
| 54 |
|
| 55 |
James |
| 56 |
|
| 57 |
|
| 58 |
|
| 59 |
|
| 60 |
|
| 61 |
-- |
| 62 |
gentoo-user@g.o mailing list |
Archives