1 |
>> My system seems to have 2 USB controllers, one 1.1 controller (OHCI) |
2 |
>> and one 2.0 controller (EHCI): |
3 |
>> |
4 |
>> 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev |
5 |
>> a3) (prog-if 10 [OHCI]) |
6 |
>> Subsystem: Micro-Star International Co., Ltd. Device 7309 |
7 |
>> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 |
8 |
>> Memory at dfe7f000 (32-bit, non-prefetchable) [size=4K] |
9 |
>> Capabilities: [44] Power Management version 2 |
10 |
>> Kernel driver in use: ohci_hcd |
11 |
>> |
12 |
>> 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev |
13 |
>> a3) (prog-if 20 [EHCI]) |
14 |
>> Subsystem: Micro-Star International Co., Ltd. Device 7309 |
15 |
>> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 |
16 |
>> Memory at dfe7ec00 (32-bit, non-prefetchable) [size=256] |
17 |
>> Capabilities: [44] Debug port: BAR=1 offset=0098 |
18 |
>> Capabilities: [80] Power Management version 2 |
19 |
>> Kernel driver in use: ehci_hcd |
20 |
>> |
21 |
>> I have 2 Philips USB webcams attached to this system and controlled by |
22 |
>> media-video/motion. One of the webcams is not functioning, and I'm |
23 |
>> supposed to make sure I don't have both of them attached to the USB |
24 |
>> 1.1 controller. How can I do that? I have: |
25 |
>> |
26 |
>> # lsusb |
27 |
>> Bus 001 Device 003: ID 04f9:002a Brother Industries, Ltd |
28 |
>> Bus 001 Device 001: ID 1d6b:0002 |
29 |
>> Bus 002 Device 003: ID 0471:0329 Philips |
30 |
>> Bus 002 Device 002: ID 0471:0329 Philips |
31 |
>> Bus 002 Device 001: ID 1d6b:0001 |
32 |
>> |
33 |
>> Is there any way to find out? |
34 |
>> |
35 |
>> - Grant |
36 |
>> |
37 |
>> |
38 |
>> |
39 |
> |
40 |
> |
41 |
> I !think! mine has that too. This is the usb part of my config: |
42 |
> |
43 |
> root@smoker / # cat /usr/src/linux/.config | grep USB | grep =y |
44 |
> CONFIG_USB_HID=y |
45 |
> CONFIG_USB_SUPPORT=y |
46 |
> CONFIG_USB_ARCH_HAS_HCD=y |
47 |
> CONFIG_USB_ARCH_HAS_OHCI=y |
48 |
> CONFIG_USB_ARCH_HAS_EHCI=y |
49 |
> CONFIG_USB=y |
50 |
> CONFIG_USB_DEVICEFS=y |
51 |
> CONFIG_USB_OHCI_HCD=y |
52 |
> CONFIG_USB_OHCI_LITTLE_ENDIAN=y |
53 |
> CONFIG_USB_ACM=y |
54 |
> CONFIG_USB_PRINTER=y |
55 |
> CONFIG_USB_STORAGE=y |
56 |
> root@smoker / # |
57 |
> |
58 |
> With mine, it tries 2.0 first then goes to the first version. My |
59 |
> printer is 2.0 but my camera is the old version, or maybe it is the |
60 |
> other way around. I got a memory stick that connects 2.0 to. Anyway, |
61 |
> that works here and it may work for you. |
62 |
> |
63 |
> Dale |
64 |
|
65 |
So it doesn't matter which slots the webcams are plugged into? |
66 |
|
67 |
- Grant |