| 1 |
On 2013-12-16 21:27, Mick wrote: |
| 2 |
> On Monday 16 Dec 2013 15:56:35 Rick "Zero_Chaos" Farina wrote: |
| 3 |
> On 12/16/2013 10:43 AM, Florian HEGRON wrote: |
| 4 |
> >> My problem : |
| 5 |
> >> Recently, I decided to install Gentoo on an old acer laptop. |
| 6 |
> >> And as everydays, when I try to install my wifi device on a Gnu/linux |
| 7 |
> >> distro, I have a problem. |
| 8 |
> >> The wireless card is Intel Pro 2200BG. |
| 9 |
> >> |
| 10 |
> >> |
| 11 |
> >> I tried to follow the simple wiki page |
| 12 |
> >> |
| 13 |
> >> : https://wiki.gentoo.org/wiki/Wifi |
| 14 |
> >> |
| 15 |
> >> It appears easy because my card is in the list. |
| 16 |
> >> I config my kernel as indicated. I tried too to active the support of |
| 17 |
> >> all proposed wifi device. |
| 18 |
> >> I rebooted on the new compiled kernel. |
| 19 |
> >> I emerge sys-firmware/iwl2000-ucode without problem. |
| 20 |
> >> After a reboot, I tried to use ifconfig -a but I only see my lo, |
| 21 |
> >> enp6s8 (ethernet), and sit0 (ipv6 I think). |
| 22 |
> >> I tried to unmerge sys-firmware/iwl2000-ucode and emerge |
| 23 |
> >> sys-kernel/linux-firmware but nothing more. |
| 24 |
> >> |
| 25 |
> >> Hi, |
| 26 |
> >> |
| 27 |
> >> did you try: # rfkill list ? ===> no ² |
| 28 |
> > |
| 29 |
> > What is the goal of this command ? |
| 30 |
> > In which package it is because I haven't this. |
| 31 |
> > |
| 32 |
> > If I have a result with this command, what do I have to do ? |
| 33 |
> > |
| 34 |
> > I will try to try today. |
| 35 |
> > |
| 36 |
> > Thank you. |
| 37 |
> |
| 38 |
> I would suggest "modprobe ipw2200" then "dmesg | grep ipw2200" and see |
| 39 |
> what is going on. might not see your hardware at all, might have a |
| 40 |
> firmware issue, might be broken. dmesg will show more. |
| 41 |
> |
| 42 |
> if you need help please reboot, modprobe ipw2200, and then provide |
| 43 |
> "dmesg" output to the list. |
| 44 |
> |
| 45 |
> -Zero |
| 46 |
> |
| 47 |
> Only to add that getting WiFi to work is not too complicated, but you |
| 48 |
> will |
| 49 |
> need to follow some basic steps to get it going: |
| 50 |
> |
| 51 |
> 1. Check that the wireless card's driver is installed in the kernel. |
| 52 |
> You can |
| 53 |
> install this as a module if you do not use wireless all the time, |
| 54 |
> otherwise |
| 55 |
> build it in the kernel. If it is installed as a module, then modprobe |
| 56 |
> it and |
| 57 |
> check in dmesg to see that it is loaded. |
| 58 |
> |
| 59 |
> 2. Check that the relevant firmware is also installed and loaded. |
| 60 |
> |
| 61 |
> 3. Check that the card is switched on on the laptop (there may be some |
| 62 |
> button |
| 63 |
> to switch on the hardware). The rfkill package can be used to check |
| 64 |
> this: |
| 65 |
> |
| 66 |
> $ eix -l rfkill |
| 67 |
> [I] net-wireless/rfkill |
| 68 |
> Available versions: |
| 69 |
> 0.4 |
| 70 |
> 0.5 |
| 71 |
> Installed versions: 0.5(14:34:30 06/29/13) |
| 72 |
> Homepage: |
| 73 |
> http://wireless.kernel.org/en/users/Documentation/rfkill |
| 74 |
> Description: Tool to read and control rfkill status through |
| 75 |
> /dev/rfkill |
| 76 |
> |
| 77 |
> |
| 78 |
> Now the card should be listed in ifconfig. Set up your network |
| 79 |
> management |
| 80 |
> solution to configure your desired wireless access point and |
| 81 |
> encryption: |
| 82 |
> |
| 83 |
> https://wiki.gentoo.org/wiki/Network_management |
| 84 |
> |
| 85 |
> Hope this helps. |
| 86 |
|
| 87 |
|
| 88 |
Thank you for help. |
| 89 |
|
| 90 |
Sorry I can't copy/past because I haven't configured MUA on my laptop. |
| 91 |
|
| 92 |
In fact I have the Inter Pro/Wirelles 2200BG and the kernel support |
| 93 |
Intel Pro/Wireless 2100. |
| 94 |
|
| 95 |
When I add the support as module, it's not loaded. Where I buit-in it, |
| 96 |
the dmesg just say me that he can't load the firmware. |
| 97 |
|
| 98 |
|
| 99 |
May be my card is not supported ? |
Archives