1 |
On 24 July 2006 00:52, Nick Rout wrote: |
2 |
|
3 |
> ivtv: ==================== START INIT IVTV ==================== |
4 |
> ivtv: version 0.4.4 (tagged release) loading |
5 |
> ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3 |
6 |
> ivtv: In case of problems please include the debug info between |
7 |
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with |
8 |
> ivtv: any module options, when mailing the ivtv-users mailinglist. |
9 |
> ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) |
10 |
> ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low) |
11 |
> -> IRQ 10 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) |
12 |
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] |
13 |
> tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) |
14 |
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] |
15 |
> cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) |
16 |
> **********cx25840 0-0044: loaded v4l-cx25840.fw firmware (14264 bytes) |
17 |
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] |
18 |
> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) |
19 |
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] |
20 |
> tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) |
21 |
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] |
22 |
> tveeprom 0-0050: The eeprom says no radio is present, but the tuner type |
23 |
> tveeprom 0-0050: indicates otherwise. I will assume that radio is present. |
24 |
> tveeprom 0-0050: Hauppauge model 26559, rev C260, serial# 2945285 |
25 |
> tveeprom 0-0050: tuner model is LG S001D MK3 (idx 60, type 38) |
26 |
> tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom |
27 |
> 0x74) tveeprom 0-0050: audio processor is CX25843 (idx 37) |
28 |
> tveeprom 0-0050: decoder processor is CX25843 (idx 30) |
29 |
> tveeprom 0-0050: has radio, has no IR remote |
30 |
> *************ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) |
31 |
> ivtv0: Encoder revision: 0x02050032 |
32 |
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) |
33 |
> ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) |
34 |
> ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) |
35 |
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB |
36 |
> total) ivtv0: Create encoder radio stream |
37 |
> tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) |
38 |
> ivtv0: Initialized WinTV PVR 150, card #0 |
39 |
> ivtv: ==================== END INIT IVTV ==================== |
40 |
|
41 |
Mine looks pretty much the same except that it detects the remote. Firmware |
42 |
gets loaded, all drivers get loaded, no errors. |
43 |
|
44 |
Meanwhile I do have audio but very very faint if i raise everything to maximum |
45 |
(mixer, speaker amplifier, ivtvctl). |
46 |
|
47 |
I don't know. Maybe the hardware is fried. |
48 |
|
49 |
Uwe |
50 |
|
51 |
-- |
52 |
Mark Twain: I rather decline two drinks than a German adjective. |
53 |
http://www.SysEx.com.na |
54 |
-- |
55 |
gentoo-user@g.o mailing list |