| 1 |
On 09/22/10 16:40, me wrote: |
| 2 |
> On Wed, Sep 22, 2010 at 7:00 PM, Bill Longman <bill.longman@×××××.com> wrote: |
| 3 |
>> I have a new workstation running 64 bits 2.6.34 gentoo sources. It's an |
| 4 |
>> HP p6520y (AthlonIIX4) with 6GB and lsusb reports an Alcor Micro 21-in-1 |
| 5 |
>> Flash Card Reader. |
| 6 |
>> |
| 7 |
>> I have no usb storage devices plugged in and I see in my dmesg many of |
| 8 |
>> the following messages: |
| 9 |
>> |
| 10 |
>> usb-storage: queuecommand called |
| 11 |
>> usb-storage: *** thread awakened. |
| 12 |
>> usb-storage: Command TEST_UNIT_READY (6 bytes) |
| 13 |
>> usb-storage: 00 00 00 00 00 00 |
| 14 |
>> usb-storage: Bulk Command S 0x43425355 T 0x5473 L 0 F 0 Trg 0 LUN 1 CL 6 |
| 15 |
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes |
| 16 |
>> usb-storage: Status code 0; transferred 31/31 |
| 17 |
>> usb-storage: -- transfer complete |
| 18 |
>> usb-storage: Bulk command transfer result=0 |
| 19 |
>> usb-storage: Attempting to get CSW... |
| 20 |
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes |
| 21 |
>> usb-storage: Status code 0; transferred 13/13 |
| 22 |
>> usb-storage: -- transfer complete |
| 23 |
>> usb-storage: Bulk status result = 0 |
| 24 |
>> usb-storage: Bulk Status S 0x53425355 T 0x5473 R 0 Stat 0x1 |
| 25 |
>> usb-storage: -- transport indicates command failure |
| 26 |
>> usb-storage: Issuing auto-REQUEST_SENSE |
| 27 |
>> usb-storage: Bulk Command S 0x43425355 T 0x5474 L 18 F 128 Trg 0 LUN 1 CL 6 |
| 28 |
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes |
| 29 |
>> usb-storage: Status code 0; transferred 31/31 |
| 30 |
>> usb-storage: -- transfer complete |
| 31 |
>> usb-storage: Bulk command transfer result=0 |
| 32 |
>> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries |
| 33 |
>> usb-storage: Status code 0; transferred 18/18 |
| 34 |
>> usb-storage: -- transfer complete |
| 35 |
>> usb-storage: Bulk data transfer result 0x0 |
| 36 |
>> usb-storage: Attempting to get CSW... |
| 37 |
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes |
| 38 |
>> usb-storage: Status code 0; transferred 13/13 |
| 39 |
>> usb-storage: -- transfer complete |
| 40 |
>> usb-storage: Bulk status result = 0 |
| 41 |
>> usb-storage: Bulk Status S 0x53425355 T 0x5474 R 0 Stat 0x0 |
| 42 |
>> usb-storage: -- Result from auto-sense is 0 |
| 43 |
>> usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 |
| 44 |
>> usb-storage: Not Ready: Medium not present |
| 45 |
>> usb-storage: scsi cmd done, result=0x2 |
| 46 |
>> usb-storage: *** thread sleeping. |
| 47 |
>> |
| 48 |
>> Any ideas who/what is doing this? How to debug? |
| 49 |
>> |
| 50 |
>> Bill |
| 51 |
>> |
| 52 |
>> -- |
| 53 |
>> Bill Longman |
| 54 |
>> Εν αρχη ην ο λογος |
| 55 |
>> |
| 56 |
> I'd guess, at a glance, that you have CONFIG_USB_STORAGE_DEBUG set in |
| 57 |
> your kernel config. |
| 58 |
> |
| 59 |
> To check if that's it (assuming you have /proc/config.gz enabled) run: |
| 60 |
> # zgrep CONFIG_USB_STORAGE_DEBUG /proc/config.gz |
| 61 |
> |
| 62 |
Yep...thanks. |
Archives