| 1 |
Hello. I have got a Laserjet 3015 with LPT port plugged on my UltraSparc |
| 2 |
5. I installed cups, the printer doesn't work. |
| 3 |
|
| 4 |
trying to figure out the reason... |
| 5 |
1) this command hangs there forever |
| 6 |
$ cat test.txt > /dev/lp0 |
| 7 |
2) installed the printer on CUPs, selected the first parallel port |
| 8 |
(parallel:/dev/lp0), send a test page, on the webpage it shows: |
| 9 |
Printer State: processing, accepting jobs. |
| 10 |
And hang there forever. |
| 11 |
|
| 12 |
I attached the dmesg file. The kernel is compiled with only PC-style |
| 13 |
parallel port support enabled, but since /dev/lp0 is successfully |
| 14 |
detected, I suppose U5 might be using a PC-style parallel port. |
| 15 |
|
| 16 |
I tried two different cables, both behave exactly the same. The two |
| 17 |
cables are from different brands, there are no printed label like |
| 18 |
'bi-directional' on the cables, so I got no way to know if the cables is |
| 19 |
qualified. |
| 20 |
|
| 21 |
Printer tested working fine using USB port. |
| 22 |
|
| 23 |
P.S. a small question: if I have the option to use Postscript or PCL (as |
| 24 |
both are possible for this type of printer and for cups), which one |
| 25 |
would result faster print speed? I guess perhaps the tigher format can |
| 26 |
result faster print speed because the bottonneck should be LPR port |
| 27 |
speed. And how slow do you suppose is LPR compare to USB for this |
| 28 |
printer? |
| 29 |
|
| 30 |
sappho ~ # equery list cups |
| 31 |
[ Searching for package 'cups' in all categories among: ] |
| 32 |
* installed packages |
| 33 |
[I--] [ ] net-print/cups-1.1.23-r7 (0) |
| 34 |
[I--] [M ] net-print/cups-pdf-2.2.0 (0) |
| 35 |
zhangweiwu@sappho ~ $ uname -a |
| 36 |
Linux sappho 2.4.28-sparc-r1 #15 Thu May 19 17:50:27 CST 2005 sparc64 sun4u TI UltraSparc IIi (Sabre) GNU/Linux |
| 37 |
zhangweiwu@sappho ~ $ dmesg |
| 38 |
PROMLIB: Sun IEEE Boot Prom 3.15.2 1998/11/10 10:35 |
| 39 |
Linux version 2.4.28-sparc-r1 (root@sappho) (gcc version 3.3.5 (Gentoo Linux 3.3.5)) #15 Thu May 19 17:50:27 CST 2005 |
| 40 |
ARCH: SUN4U |
| 41 |
Ethernet address: 08:00:20:b0:99:30 |
| 42 |
On node 0 totalpages: 32046 |
| 43 |
zone(0): 49057 pages. |
| 44 |
zone(1): 0 pages. |
| 45 |
zone(2): 0 pages. |
| 46 |
Found CPU 0 (node=f006d098,mid=0) |
| 47 |
Found 1 CPU prom device tree node(s). |
| 48 |
Kernel command line: root=/dev/hde1 |
| 49 |
Console: colour dummy device 80x25 |
| 50 |
Calibrating delay loop... 665.19 BogoMIPS |
| 51 |
Memory: 251704k available (2896k kernel code, 1104k data, 200k init) [fffff80000000000,0000000017f42000] |
| 52 |
Dentry cache hash table entries: 32768 (order: 6, 524288 bytes) |
| 53 |
Inode cache hash table entries: 16384 (order: 5, 262144 bytes) |
| 54 |
Mount cache hash table entries: 512 (order: 0, 8192 bytes) |
| 55 |
Buffer cache hash table entries: 8192 (order: 3, 65536 bytes) |
| 56 |
Page-cache hash table entries: 32768 (order: 5, 262144 bytes) |
| 57 |
POSIX conformance testing by UNIFIX |
| 58 |
PCI: Probing for controllers. |
| 59 |
PCI: Found SABRE, main regs at 000001fe00000000, wsync at 000001fe00001c20 |
| 60 |
SABRE: Shared PCI config space at 000001fe01000000 |
| 61 |
SABRE: DVMA at c0000000 [20000000] |
| 62 |
PCI-IRQ: Routing bus[ 2] slot[ 1] map[0] to INO[10] |
| 63 |
PCI-IRQ: Routing bus[ 2] slot[ 2] map[0] to INO[14] |
| 64 |
PCI-IRQ: Routing bus[ 2] slot[ 2] map[0] to INO[15] |
| 65 |
PCI-IRQ: Routing bus[ 2] slot[ 2] map[0] to INO[16] |
| 66 |
PCI-IRQ: Routing bus[ 3] slot[ 4] map[1] to INO[18] |
| 67 |
PCI-IRQ: Routing bus[ 3] slot[ 5] map[1] to INO[19] |
| 68 |
PCI0(PBMA): Bus running at 33MHz |
| 69 |
PCI-IRQ: Routing bus[ 1] slot[ 1] map[0] to INO[21] |
| 70 |
PCI-IRQ: Routing bus[ 1] slot[ 2] map[0] to INO[0f] |
| 71 |
PCI-IRQ: Routing bus[ 1] slot[ 3] map[0] to INO[20] |
| 72 |
PCI0(PBMB): Bus running at 33MHz |
| 73 |
ebus0: [auxio] [power] [SUNW,pll] [se] [su] [su] [ecpp] [fdthree] [eeprom] [flashprom] [SUNW,CS4231] |
| 74 |
PCIO serial driver version 1.54 |
| 75 |
su(mouse) at 0x1fff13062f8 (irq = 4,7ea) is a 16550A |
| 76 |
Sun Mouse-Systems mouse driver version 1.00 |
| 77 |
su(kbd) at 0x1fff13083f8 (irq = 9,7e9) is a 16550A |
| 78 |
Sun TYPE 5 keyboard detected without keyclick |
| 79 |
SAB82532 serial driver version 1.65 |
| 80 |
ttyS00 at 0x1fff1400000 (irq = 12,7eb) is a SAB82532 V3.2 |
| 81 |
ttyS01 at 0x1fff1400040 (irq = 12,7eb) is a SAB82532 V3.2 |
| 82 |
power: Control reg at 000001fff1724000 ... powerd running. |
| 83 |
Linux NET4.0 for Linux 2.4 |
| 84 |
Based upon Swansea University Computer Society NET3.039 |
| 85 |
Initializing RT netlink socket |
| 86 |
Starting kswapd |
| 87 |
Journalled Block Device driver loaded |
| 88 |
devfs: v1.12c (20020818) Richard Gooch (rgooch@××××××××××.au) |
| 89 |
devfs: boot_options: 0x1 |
| 90 |
Installing knfsd (copyright (C) 1996 okir@×××××××××.de). |
| 91 |
parport0: PC-style at 0x1fff13043bc (0x1fff13047bc), irq 8687936, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA] |
| 92 |
i2c-core.o: i2c core module version 2.6.1 (20010830) |
| 93 |
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) |
| 94 |
i2c-core.o: driver i2c-dev dummy driver registered. |
| 95 |
i2c-algo-bit.o: i2c bit algorithm module |
| 96 |
i2c-proc.o version 2.6.1 (20010830) |
| 97 |
atyfb: 3D RAGE PRO (PQFP, PCI) [0x4750 rev 0x7c] 4M SGRAM, 14.31818 MHz XTAL, 230 MHz PLL, 100 Mhz MCLK, 100 Mhz XCLK |
| 98 |
Console: switching to colour frame buffer device 160x64 |
| 99 |
fb0: ATY Mach64 frame buffer device on PCI |
| 100 |
lp0: using parport0 (interrupt-driven). |
| 101 |
rtc_init: no PC rtc found |
| 102 |
loop: loaded (max 8 devices) |
| 103 |
sunhme.c:v2.01 26/Mar/2002 David S. Miller (davem@××××××.com) |
| 104 |
eth0: HAPPY MEAL (PCI/CheerIO) 10/100BaseT Ethernet 08:00:20:b0:99:30 |
| 105 |
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html |
| 106 |
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@××××××××××.sg> and others |
| 107 |
eth1: OEM i82557/i82558 10/100 Ethernet, 00:90:27:D5:C7:05, IRQ 8687616. |
| 108 |
Receiver lock-up bug exists -- enabling work-around. |
| 109 |
Board assembly 751110-001, Physical connectors present: RJ45 |
| 110 |
Primary interface chip i82555 PHY #1. |
| 111 |
General self-test: passed. |
| 112 |
Serial sub-system self-test: passed. |
| 113 |
Internal registers self-test: passed. |
| 114 |
ROM checksum self-test: passed (0x43f0c924). |
| 115 |
Receiver lock-up workaround activated. |
| 116 |
eth2: OEM i82557/i82558 10/100 Ethernet, 00:90:27:D5:C7:06, IRQ 8687648. |
| 117 |
Receiver lock-up bug exists -- enabling work-around. |
| 118 |
Board assembly 751110-001, Physical connectors present: RJ45 |
| 119 |
Primary interface chip i82555 PHY #1. |
| 120 |
General self-test: passed. |
| 121 |
Serial sub-system self-test: passed. |
| 122 |
Internal registers self-test: passed. |
| 123 |
ROM checksum self-test: passed (0x43f0c924). |
| 124 |
Receiver lock-up workaround activated. |
| 125 |
[drm] Initialized r128 2.2.0 20010917 on minor 0 |
| 126 |
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 |
| 127 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
| 128 |
PDC20262: IDE controller at PCI slot 02:01.0 |
| 129 |
PDC20262: chipset revision 1 |
| 130 |
PDC20262: not 100% native mode: will probe irqs later |
| 131 |
PDC20262: ROM enabled at 0x1ff00000000 |
| 132 |
PDC20262: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode. |
| 133 |
PDC20262: FORCING BURST BIT 0x00->0x01 ACTIVE |
| 134 |
ide2: BM-DMA at 0x1fe02002040-0x1fe02002047, BIOS settings: hde:DMA, hdf:DMA |
| 135 |
ide3: BM-DMA at 0x1fe02002048-0x1fe0200204f, BIOS settings: hdg:DMA, hdh:pio |
| 136 |
CMD646: IDE controller at PCI slot 01:03.0 |
| 137 |
CMD646: chipset revision 3 |
| 138 |
CMD646: chipset revision 0x03, MultiWord DMA Force Limited |
| 139 |
CMD646: 100% native mode on irq 4,7e0 |
| 140 |
ide0: BM-DMA at 0x1fe02c00020-0x1fe02c00027, BIOS settings: hda:pio, hdb:pio |
| 141 |
ide1: BM-DMA at 0x1fe02c00028-0x1fe02c0002f, BIOS settings: hdc:pio, hdd:pio |
| 142 |
hda: QUANTUM FIREBALL1280A, ATA DISK drive |
| 143 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
| 144 |
hde: probing with STATUS(0x50) instead of ALTSTATUS(0x00) |
| 145 |
hde: ST320423A, ATA DISK drive |
| 146 |
hdg: ST3160212A, ATA DISK drive |
| 147 |
ide0 at 0x1fe02c00000-0x1fe02c00007,0x1fe02c0000a on irq 4,7e0 |
| 148 |
ide2 at 0x1fe02002000-0x1fe02002007,0x1fe0200200a on irq 4,7d0 |
| 149 |
ide3 at 0x1fe02002010-0x1fe02002017,0x1fe0200201a on irq 4,7d0 |
| 150 |
hda: attached ide-disk driver. |
| 151 |
hda: 2503872 sectors (1282 MB) w/83KiB Cache, CHS=2484/16/63, DMA |
| 152 |
hde: attached ide-disk driver. |
| 153 |
hde: host protected area => 1 |
| 154 |
hde: 40011300 sectors (20486 MB) w/512KiB Cache, CHS=39693/16/63, UDMA(66) |
| 155 |
hdg: attached ide-disk driver. |
| 156 |
hdg: host protected area => 1 |
| 157 |
hdg: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(66) |
| 158 |
Partition check: |
| 159 |
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 |
| 160 |
/dev/ide/host2/bus0/target0/lun0: p1 p2 p3 p4 p5 p6 |
| 161 |
/dev/ide/host2/bus1/target0/lun0: p1 p2 p3 p4 p5 p6 |
| 162 |
SCSI subsystem driver Revision: 1.00 |
| 163 |
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 |
| 164 |
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 |
| 165 |
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 |
| 166 |
OBP Flash: RD 1fff0000000[100000] WR 1fff0000000[100000] |
| 167 |
audio0: cs4231a(eb2) at 1fff1200000 irq 13,7e3 |
| 168 |
usb.c: registered new driver usbdevfs |
| 169 |
usb.c: registered new driver hub |
| 170 |
host/usb-ohci.c: USB OHCI at membase 0x1ff00520000, IRQ 10,7d4 |
| 171 |
host/usb-ohci.c: usb-02:02.0, NEC Corporation USB |
| 172 |
usb.c: new USB bus registered, assigned bus number 1 |
| 173 |
hub.c: USB hub found |
| 174 |
hub.c: 3 ports detected |
| 175 |
host/usb-ohci.c: USB OHCI at membase 0x1ff00522000, IRQ 10,7d5 |
| 176 |
host/usb-ohci.c: usb-02:02.1, NEC Corporation USB (#2) |
| 177 |
usb.c: new USB bus registered, assigned bus number 2 |
| 178 |
hub.c: USB hub found |
| 179 |
hub.c: 2 ports detected |
| 180 |
hub.c: new USB device 02:02.0-1, assigned address 2 |
| 181 |
usb.c: USB device 2 (vend/prod 0x4b8/0x5) is not claimed by any active driver. |
| 182 |
usb.c: registered new driver hid |
| 183 |
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@××××.cz> |
| 184 |
hid-core.c: USB HID support drivers |
| 185 |
usb.c: registered new driver usblp |
| 186 |
printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005 |
| 187 |
printer.c: v0.13: USB Printer Device Class driver |
| 188 |
Linux video capture interface: v1.00 |
| 189 |
mice: PS/2 mouse device common for all mice |
| 190 |
Initializing Cryptographic API |
| 191 |
NET4: Linux TCP/IP 1.0 for NET4.0 |
| 192 |
IP Protocols: ICMP, UDP, TCP |
| 193 |
IP: routing cache hash table of 4096 buckets, 32Kbytes |
| 194 |
TCP: Hash tables configured (established 32768 bind 32768) |
| 195 |
ip_conntrack version 2.1 (983 buckets, 7864 max) - 416 bytes per conntrack |
| 196 |
ip_tables: (C) 2000-2002 Netfilter core team |
| 197 |
ipt_recent v0.3.1: Stephen Frost <sfrost@×××××××.net>. http://snowman.net/projects/ipt_recent/ |
| 198 |
arp_tables: (C) 2002 David S. Miller |
| 199 |
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. |
| 200 |
kjournald starting. Commit interval 5 seconds |
| 201 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 202 |
VFS: Mounted root (ext3 filesystem) readonly. |
| 203 |
Mounted devfs on /dev |
| 204 |
Adding Swap: 996008k swap-space (priority -1) |
| 205 |
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended |
| 206 |
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide2(33,1), internal journal |
| 207 |
kjournald starting. Commit interval 5 seconds |
| 208 |
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended |
| 209 |
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide2(33,4), internal journal |
| 210 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 211 |
kjournald starting. Commit interval 5 seconds |
| 212 |
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended |
| 213 |
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide2(33,5), internal journal |
| 214 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 215 |
kjournald starting. Commit interval 5 seconds |
| 216 |
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended |
| 217 |
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal |
| 218 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 219 |
kjournald starting. Commit interval 5 seconds |
| 220 |
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended |
| 221 |
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide2(33,6), internal journal |
| 222 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 223 |
eth0: Link is up using internal transceiver at 100Mb/s, Full Duplex. |
| 224 |
sys32_ioctl(usb:2425): Unknown cmd fd(0) cmd(44005001) arg(efffebc8) |
| 225 |
sys32_ioctl(hpiod:2453): Unknown cmd fd(7) cmd(44005001) arg(00034b70) |
| 226 |
DMA write timed out |
| 227 |
eth2: TX underrun, threshold adjusted. |
| 228 |
eth2: TX underrun, threshold adjusted. |
| 229 |
eth2: TX underrun, threshold adjusted. |
| 230 |
eth2: TX underrun, threshold adjusted. |
| 231 |
eth2: TX underrun, threshold adjusted. |
| 232 |
eth2: TX underrun, threshold adjusted. |
| 233 |
eth2: TX underrun, threshold adjusted. |
| 234 |
parport0: FIFO is stuck |
| 235 |
parport0: BUSY timeout (1) in compat_write_block_pio |
| 236 |
DMA write timed out |
| 237 |
hub.c: new USB device 02:02.1-1, assigned address 2 |
| 238 |
printer.c: usblp1: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1617 |
| 239 |
eth2: TX underrun, threshold adjusted. |
| 240 |
parport0: FIFO is stuck |
| 241 |
parport0: BUSY timeout (1) in compat_write_block_pio |
| 242 |
DMA write timed out |
| 243 |
parport0: FIFO is stuck |
| 244 |
parport0: BUSY timeout (1) in compat_write_block_pio |
| 245 |
DMA write timed out |
| 246 |
parport0: FIFO is stuck |
| 247 |
parport0: BUSY timeout (1) in compat_write_block_pio |
| 248 |
DMA write timed out |
| 249 |
|
| 250 |
|
| 251 |
-- |
| 252 |
gentoo-server@g.o mailing list |
Archives