| 1 |
(note dmesg follows message) |
| 2 |
|
| 3 |
Out of 12 partitions in my setup 8 are reiserfs. During bootup I see |
| 4 |
them go by being checked, but always the last one /dev/hda11 fails |
| 5 |
with this message: |
| 6 |
|
| 7 |
fsck could not repair all errors .... |
| 8 |
|
| 9 |
And drops me into the repair shell. |
| 10 |
|
| 11 |
This has happened over several kernels and for mnths. |
| 12 |
I finally just took to C-d to finish booting. This is after stopping |
| 13 |
to reiserfsck /dev/hda11 many times. It always passes with no error |
| 14 |
messages. |
| 15 |
|
| 16 |
Oddly, the drive is always mounted once boot is complete (I mean even |
| 17 |
when I just press Ctrl-d to by-pass fixing.) And no problems |
| 18 |
read/write to it occur. |
| 19 |
|
| 20 |
I finally reformatted /dev/hda11 to ext3. Now the last reiserfs |
| 21 |
partition that shows up in boot messages is /dev/hda9 and it fails the |
| 22 |
same way. |
| 23 |
|
| 24 |
These facts lead me to believe it isn't really a reiserfs failure at |
| 25 |
all but something earlier that just shows up at that point, but I |
| 26 |
cannot fathom out what. |
| 27 |
|
| 28 |
dmesg: |
| 29 |
|
| 30 |
Linux version 2.6.17-gentoo-r8 (root@reader) (gcc version 4.1.1 (Gentoo 4.1.1-r1)) #1 SMP Wed Sep 13 10:39:54 CDT 2006 |
| 31 |
BIOS-provided physical RAM map: |
| 32 |
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) |
| 33 |
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) |
| 34 |
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) |
| 35 |
BIOS-e820: 0000000000100000 - 000000007fff0000 (usable) |
| 36 |
BIOS-e820: 000000007fff0000 - 000000007fff8000 (ACPI data) |
| 37 |
BIOS-e820: 000000007fff8000 - 0000000080000000 (ACPI NVS) |
| 38 |
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) |
| 39 |
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) |
| 40 |
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) |
| 41 |
1151MB HIGHMEM available. |
| 42 |
896MB LOWMEM available. |
| 43 |
found SMP MP-table at 000fc0f0 |
| 44 |
On node 0 totalpages: 524272 |
| 45 |
DMA zone: 4096 pages, LIFO batch:0 |
| 46 |
Normal zone: 225280 pages, LIFO batch:31 |
| 47 |
HighMem zone: 294896 pages, LIFO batch:31 |
| 48 |
DMI 2.3 present. |
| 49 |
ACPI: RSDP (v000 AMI ) @ 0x000fa3a0 |
| 50 |
ACPI: RSDT (v001 AMIINT INTEL865 0x00000010 MSFT 0x00000097) @ 0x7fff0000 |
| 51 |
ACPI: FADT (v001 AMIINT INTEL865 0x00000011 MSFT 0x00000097) @ 0x7fff0030 |
| 52 |
ACPI: MADT (v001 AMIINT INTEL865 0x00000009 MSFT 0x00000097) @ 0x7fff00c0 |
| 53 |
ACPI: DSDT (v001 INTEL I865G 0x00001000 MSFT 0x0100000d) @ 0x00000000 |
| 54 |
ACPI: PM-Timer IO Port: 0x808 |
| 55 |
ACPI: Local APIC address 0xfee00000 |
| 56 |
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) |
| 57 |
Processor #0 15:4 APIC version 20 |
| 58 |
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled) |
| 59 |
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) |
| 60 |
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 |
| 61 |
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) |
| 62 |
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) |
| 63 |
ACPI: IRQ0 used by override. |
| 64 |
ACPI: IRQ2 used by override. |
| 65 |
ACPI: IRQ9 used by override. |
| 66 |
Enabling APIC mode: Flat. Using 1 I/O APICs |
| 67 |
Using ACPI (MADT) for SMP configuration information |
| 68 |
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000) |
| 69 |
Built 1 zonelists |
| 70 |
Kernel command line: root=/dev/hda5 vga=0x31A video=vesafb:mtrr,ywrap |
| 71 |
mapped APIC to ffffd000 (fee00000) |
| 72 |
mapped IOAPIC to ffffc000 (fec00000) |
| 73 |
Enabling fast FPU save and restore... done. |
| 74 |
Enabling unmasked SIMD FPU exception support... done. |
| 75 |
Initializing CPU#0 |
| 76 |
CPU 0 irqstacks, hard=c0467000 soft=c045f000 |
| 77 |
PID hash table entries: 4096 (order: 12, 16384 bytes) |
| 78 |
Detected 3067.474 MHz processor. |
| 79 |
Using pmtmr for high-res timesource |
| 80 |
Speakup v-2.00 CVS: Mon May 1 09:46:33 EDT 2006 : initialized |
| 81 |
Console: colour dummy device 80x25 |
| 82 |
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) |
| 83 |
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) |
| 84 |
Memory: 2074920k/2097088k available (2412k kernel code, 21036k reserved, 791k data, 204k init, 1179584k highmem) |
| 85 |
Checking if this processor honours the WP bit even in supervisor mode... Ok. |
| 86 |
Calibrating delay using timer specific routine.. 6140.10 BogoMIPS (lpj=12280208) |
| 87 |
Mount-cache hash table entries: 512 |
| 88 |
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 |
| 89 |
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 |
| 90 |
monitor/mwait feature present. |
| 91 |
using mwait in idle threads. |
| 92 |
CPU: Trace cache: 12K uops, L1 D cache: 16K |
| 93 |
CPU: L2 cache: 256K |
| 94 |
CPU: Hyper-Threading is disabled |
| 95 |
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000180 0000441d 00000000 00000000 |
| 96 |
Intel machine check architecture supported. |
| 97 |
Intel machine check reporting enabled on CPU#0. |
| 98 |
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available |
| 99 |
CPU0: Thermal monitoring enabled |
| 100 |
Checking 'hlt' instruction... OK. |
| 101 |
SMP alternatives: switching to UP code |
| 102 |
Freeing SMP alternatives: 16k freed |
| 103 |
CPU0: Intel(R) Celeron(R) CPU 3.06GHz stepping 01 |
| 104 |
Total of 1 processors activated (6140.10 BogoMIPS). |
| 105 |
ENABLING IO-APIC IRQs |
| 106 |
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 |
| 107 |
Brought up 1 CPUs |
| 108 |
migration_cost=0 |
| 109 |
NET: Registered protocol family 16 |
| 110 |
EISA bus registered |
| 111 |
ACPI: bus type pci registered |
| 112 |
PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=2 |
| 113 |
Setting up standard PCI resources |
| 114 |
ACPI: Subsystem revision 20060127 |
| 115 |
ACPI: Interpreter enabled |
| 116 |
ACPI: Using IOAPIC for interrupt routing |
| 117 |
ACPI: PCI Root Bridge [PCI0] (0000:00) |
| 118 |
PCI: Probing PCI hardware (bus 00) |
| 119 |
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO |
| 120 |
PCI quirk: region 0400-043f claimed by ICH4 GPIO |
| 121 |
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 |
| 122 |
Boot video device is 0000:01:00.0 |
| 123 |
PCI: Transparent bridge - 0000:00:1e.0 |
| 124 |
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] |
| 125 |
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT] |
| 126 |
ACPI: Power Resource [URP1] (off) |
| 127 |
ACPI: Power Resource [URP2] (off) |
| 128 |
ACPI: Power Resource [FDDP] (off) |
| 129 |
ACPI: Power Resource [LPTP] (off) |
| 130 |
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12 14 15) |
| 131 |
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12 14 15) |
| 132 |
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12 14 15) |
| 133 |
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 6 7 10 11 12 14 15) |
| 134 |
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 *10 11 12 14 15) |
| 135 |
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. |
| 136 |
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. |
| 137 |
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 12 14 15) |
| 138 |
Linux Plug and Play Support v0.97 (c) Adam Belay |
| 139 |
pnp: PnP ACPI init |
| 140 |
pnp: PnP ACPI: found 13 devices |
| 141 |
SCSI subsystem initialized |
| 142 |
PCI: Using ACPI for IRQ routing |
| 143 |
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report |
| 144 |
PCI: Bridge: 0000:00:01.0 |
| 145 |
IO window: disabled. |
| 146 |
MEM window: fc900000-fe9fffff |
| 147 |
PREFETCH window: bff00000-dfefffff |
| 148 |
PCI: Bridge: 0000:00:1e.0 |
| 149 |
IO window: c000-cfff |
| 150 |
MEM window: fea00000-feafffff |
| 151 |
PREFETCH window: 88000000-880fffff |
| 152 |
PCI: Setting latency timer of device 0000:00:1e.0 to 64 |
| 153 |
NET: Registered protocol family 2 |
| 154 |
IP route cache hash table entries: 32768 (order: 5, 131072 bytes) |
| 155 |
TCP established hash table entries: 262144 (order: 9, 2097152 bytes) |
| 156 |
TCP bind hash table entries: 65536 (order: 7, 524288 bytes) |
| 157 |
TCP: Hash tables configured (established 262144 bind 65536) |
| 158 |
TCP reno registered |
| 159 |
audit: initializing netlink socket (disabled) |
| 160 |
audit(1160144035.684:1): initialized |
| 161 |
highmem bounce pool size: 64 pages |
| 162 |
VFS: Disk quotas dquot_6.5.1 |
| 163 |
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) |
| 164 |
squashfs: version 3.0 (2006/03/15) Phillip Lougher |
| 165 |
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled |
| 166 |
SGI XFS Quota Management subsystem |
| 167 |
Initializing Cryptographic API |
| 168 |
io scheduler noop registered |
| 169 |
io scheduler deadline registered (default) |
| 170 |
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 ) |
| 171 |
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 5120k, total 262144k |
| 172 |
vesafb: mode is 1280x1024x16, linelength=2560, pages=1 |
| 173 |
vesafb: protected mode interface info at c000:e6e0 |
| 174 |
vesafb: pmi: set display start = c00ce716, set palette = c00ce780 |
| 175 |
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da |
| 176 |
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=2048 |
| 177 |
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 |
| 178 |
Console: switching to colour frame buffer device 160x64 |
| 179 |
fb0: VESA VGA frame buffer device |
| 180 |
isapnp: Scanning for PnP cards... |
| 181 |
isapnp: No Plug & Play device found |
| 182 |
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled |
| 183 |
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A |
| 184 |
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A |
| 185 |
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A |
| 186 |
00:0b: ttyS2 at I/O 0x3e8 (irq = 0) is a 16550A |
| 187 |
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 |
| 188 |
serio: i8042 AUX port at 0x60,0x64 irq 12 |
| 189 |
serio: i8042 KBD port at 0x60,0x64 irq 1 |
| 190 |
mice: PS/2 mouse device common for all mice |
| 191 |
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize |
| 192 |
loop: loaded (max 8 devices) |
| 193 |
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 |
| 194 |
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx |
| 195 |
ICH5: IDE controller at PCI slot 0000:00:1f.1 |
| 196 |
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) |
| 197 |
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169 |
| 198 |
ICH5: chipset revision 2 |
| 199 |
ICH5: not 100% native mode: will probe irqs later |
| 200 |
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA |
| 201 |
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA |
| 202 |
Probing IDE interface ide0... |
| 203 |
input: AT Translated Set 2 keyboard as /class/input/input0 |
| 204 |
hda: ST3160021A, ATA DISK drive |
| 205 |
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 |
| 206 |
hdb: WDC WD3000JB-00KFA0, ATA DISK drive |
| 207 |
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 |
| 208 |
Probing IDE interface ide1... |
| 209 |
hdc: LITE-ON CD-ROM LTN-5291S, ATAPI CD/DVD-ROM drive |
| 210 |
hdd: WDC WD1600JB-00EVA0, ATA DISK drive |
| 211 |
ide1 at 0x170-0x177,0x376 on irq 15 |
| 212 |
hda: max request size: 512KiB |
| 213 |
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100) |
| 214 |
hda: cache flushes supported |
| 215 |
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 > |
| 216 |
hdb: max request size: 512KiB |
| 217 |
hdb: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, UDMA(100) |
| 218 |
hdb: cache flushes supported |
| 219 |
hdb: hdb1 < hdb5 hdb6 > hdb2 |
| 220 |
hdd: max request size: 512KiB |
| 221 |
hdd: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) |
| 222 |
hdd: cache flushes supported |
| 223 |
hdd: hdd1 hdd2 < hdd5 hdd6 hdd7 > |
| 224 |
hdc: ATAPI 52X CD-ROM drive, 96kB Cache, UDMA(33) |
| 225 |
Uniform CD-ROM driver Revision: 3.20 |
| 226 |
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 |
| 227 |
md: bitmap version 4.39 |
| 228 |
EISA: Probing bus 0 at eisa.0 |
| 229 |
EISA: Detected 0 cards. |
| 230 |
TCP bic registered |
| 231 |
NET: Registered protocol family 1 |
| 232 |
NET: Registered protocol family 17 |
| 233 |
Using IPI Shortcut mode |
| 234 |
md: Autodetecting RAID arrays. |
| 235 |
md: autorun ... |
| 236 |
md: ... autorun DONE. |
| 237 |
ReiserFS: hda5: found reiserfs format "3.6" with standard journal |
| 238 |
ReiserFS: hda5: using ordered data mode |
| 239 |
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 240 |
ReiserFS: hda5: checking transaction log (hda5) |
| 241 |
ReiserFS: hda5: Using r5 hash to sort names |
| 242 |
VFS: Mounted root (reiserfs filesystem) readonly. |
| 243 |
Freeing unused kernel memory: 204k freed |
| 244 |
parport: PnPBIOS parport detected. |
| 245 |
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] |
| 246 |
usbcore: registered new driver usbfs |
| 247 |
usbcore: registered new driver hub |
| 248 |
USB Universal Host Controller Interface driver v3.0 |
| 249 |
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177 |
| 250 |
PCI: Setting latency timer of device 0000:00:1d.0 to 64 |
| 251 |
uhci_hcd 0000:00:1d.0: UHCI Host Controller |
| 252 |
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 |
| 253 |
uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000e000 |
| 254 |
usb usb1: configuration #1 chosen from 1 choice |
| 255 |
hub 1-0:1.0: USB hub found |
| 256 |
hub 1-0:1.0: 2 ports detected |
| 257 |
Linux agpgart interface v0.101 (c) Dave Jones |
| 258 |
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185 |
| 259 |
PCI: Setting latency timer of device 0000:00:1d.1 to 64 |
| 260 |
uhci_hcd 0000:00:1d.1: UHCI Host Controller |
| 261 |
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 |
| 262 |
uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000e400 |
| 263 |
usb usb2: configuration #1 chosen from 1 choice |
| 264 |
hub 2-0:1.0: USB hub found |
| 265 |
hub 2-0:1.0: 2 ports detected |
| 266 |
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169 |
| 267 |
PCI: Setting latency timer of device 0000:00:1d.2 to 64 |
| 268 |
uhci_hcd 0000:00:1d.2: UHCI Host Controller |
| 269 |
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 |
| 270 |
uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000e800 |
| 271 |
usb usb3: configuration #1 chosen from 1 choice |
| 272 |
hub 3-0:1.0: USB hub found |
| 273 |
hub 3-0:1.0: 2 ports detected |
| 274 |
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 177 |
| 275 |
PCI: Setting latency timer of device 0000:00:1d.3 to 64 |
| 276 |
uhci_hcd 0000:00:1d.3: UHCI Host Controller |
| 277 |
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 |
| 278 |
uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000ec00 |
| 279 |
usb usb4: configuration #1 chosen from 1 choice |
| 280 |
hub 4-0:1.0: USB hub found |
| 281 |
hub 4-0:1.0: 2 ports detected |
| 282 |
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193 |
| 283 |
PCI: Setting latency timer of device 0000:00:1d.7 to 64 |
| 284 |
ehci_hcd 0000:00:1d.7: EHCI Host Controller |
| 285 |
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 |
| 286 |
ehci_hcd 0000:00:1d.7: debug port 1 |
| 287 |
PCI: cache line size of 128 is not supported by device 0000:00:1d.7 |
| 288 |
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xfebffc00 |
| 289 |
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 |
| 290 |
usb usb5: configuration #1 chosen from 1 choice |
| 291 |
hub 5-0:1.0: USB hub found |
| 292 |
hub 5-0:1.0: 8 ports detected |
| 293 |
agpgart: Detected an Intel 865 Chipset. |
| 294 |
agpgart: AGP aperture is 256M @ 0xe0000000 |
| 295 |
r8169 Gigabit Ethernet driver 2.2LK loaded |
| 296 |
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 185 |
| 297 |
eth0: Identified chip type is 'RTL8169s/8110s'. |
| 298 |
eth0: RTL8169 at 0xf8842f00, 00:40:f4:b5:29:41, IRQ 185 |
| 299 |
r8169 Gigabit Ethernet driver 2.2LK loaded |
| 300 |
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 20 (level, low) -> IRQ 201 |
| 301 |
eth1: Identified chip type is 'RTL8169s/8110s'. |
| 302 |
eth1: RTL8169 at 0xf887ee00, 00:11:09:ee:6c:04, IRQ 201 |
| 303 |
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 209 |
| 304 |
PCI: Setting latency timer of device 0000:00:1f.5 to 64 |
| 305 |
intel8x0_measure_ac97_clock: measured 58725 usecs |
| 306 |
intel8x0: clocking to 48000 |
| 307 |
hw_random: RNG not detected |
| 308 |
hw_random: RNG not detected |
| 309 |
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@××××××.com |
| 310 |
fuse init (API version 7.6) |
| 311 |
Initializing USB Mass Storage driver... |
| 312 |
usbcore: registered new driver usb-storage |
| 313 |
USB Mass Storage support registered. |
| 314 |
ReiserFS: hda6: found reiserfs format "3.6" with standard journal |
| 315 |
ReiserFS: hda6: using ordered data mode |
| 316 |
ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 317 |
ReiserFS: hda6: checking transaction log (hda6) |
| 318 |
ReiserFS: hda6: Using r5 hash to sort names |
| 319 |
ReiserFS: hda7: found reiserfs format "3.6" with standard journal |
| 320 |
ReiserFS: hda7: using ordered data mode |
| 321 |
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 322 |
ReiserFS: hda7: checking transaction log (hda7) |
| 323 |
ReiserFS: hda7: Using r5 hash to sort names |
| 324 |
ReiserFS: hda8: found reiserfs format "3.6" with standard journal |
| 325 |
ReiserFS: hda8: using ordered data mode |
| 326 |
ReiserFS: hda8: journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 327 |
ReiserFS: hda8: checking transaction log (hda8) |
| 328 |
ReiserFS: hda8: Using r5 hash to sort names |
| 329 |
ReiserFS: hda9: found reiserfs format "3.6" with standard journal |
| 330 |
ReiserFS: hda9: using ordered data mode |
| 331 |
ReiserFS: hda9: journal params: device hda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 332 |
ReiserFS: hda9: checking transaction log (hda9) |
| 333 |
ReiserFS: hda9: Using r5 hash to sort names |
| 334 |
kjournald starting. Commit interval 5 seconds |
| 335 |
EXT3 FS on hda11, internal journal |
| 336 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 337 |
kjournald starting. Commit interval 5 seconds |
| 338 |
EXT3 FS on hdb2, internal journal |
| 339 |
EXT3-fs: mounted filesystem with ordered data mode. |
| 340 |
ReiserFS: hdb5: found reiserfs format "3.6" with standard journal |
| 341 |
ReiserFS: hdb5: using ordered data mode |
| 342 |
ReiserFS: hdb5: journal params: device hdb5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 343 |
ReiserFS: hdb5: checking transaction log (hdb5) |
| 344 |
ReiserFS: hdb5: Using r5 hash to sort names |
| 345 |
ReiserFS: hdb6: found reiserfs format "3.6" with standard journal |
| 346 |
ReiserFS: hdb6: using ordered data mode |
| 347 |
ReiserFS: hdb6: journal params: device hdb6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 348 |
ReiserFS: hdb6: checking transaction log (hdb6) |
| 349 |
ReiserFS: hdb6: Using r5 hash to sort names |
| 350 |
ReiserFS: hdd5: found reiserfs format "3.6" with standard journal |
| 351 |
ReiserFS: hdd5: using ordered data mode |
| 352 |
ReiserFS: hdd5: journal params: device hdd5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 353 |
ReiserFS: hdd5: checking transaction log (hdd5) |
| 354 |
ReiserFS: hdd5: Using r5 hash to sort names |
| 355 |
ReiserFS: hdd6: found reiserfs format "3.6" with standard journal |
| 356 |
ReiserFS: hdd6: using ordered data mode |
| 357 |
ReiserFS: hdd6: journal params: device hdd6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 358 |
ReiserFS: hdd6: checking transaction log (hdd6) |
| 359 |
ReiserFS: hdd6: Using r5 hash to sort names |
| 360 |
ReiserFS: hdd7: found reiserfs format "3.6" with standard journal |
| 361 |
ReiserFS: hdd7: using ordered data mode |
| 362 |
ReiserFS: hdd7: journal params: device hdd7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 |
| 363 |
ReiserFS: hdd7: checking transaction log (hdd7) |
| 364 |
ReiserFS: hdd7: Using r5 hash to sort names |
| 365 |
Adding 2008116k swap on /dev/hda2. Priority:-1 extents:1 across:2008116k |
| 366 |
Real Time Clock Driver v1.12ac |
| 367 |
r8169: eth0: link up |
| 368 |
|
| 369 |
-- |
| 370 |
gentoo-user@g.o mailing list |
Archives