1 |
Helmut Jarausch <jarausch@××××××××××××××××.de> writes: |
2 |
|
3 |
> On 21 Mar, Harry Putnam wrote: |
4 |
>> Harry Putnam <reader@×××××××.com> writes: |
5 |
>> |
6 |
>> Forgot to give kernel version: |
7 |
>> uname -r |
8 |
>> 2.6.33-gentoo |
9 |
>> |
10 |
>>> I see lots of bug reports about this in several linux OSs but not able |
11 |
>>> to see a solution. |
12 |
>>> |
13 |
>>> I've make the propers kernel settings and the w83627hf modules is |
14 |
>>> built and available in /lib/modules/* |
15 |
>>> I tried rebuilding the kernel with that stuff built-in. but then |
16 |
>>> lm_sensors couldn't even find tools to work with when running |
17 |
>>> sensors-detect |
18 |
>>> |
19 |
>>> So calling `sensors' just in case it would work: |
20 |
>>> # sensors |
21 |
>>> No sensors found! |
22 |
>>> Make sure you loaded all the kernel drivers you need. |
23 |
>>> Try sensors-detect to find out which these are. |
24 |
>>> |
25 |
|
26 |
[...] |
27 |
|
28 |
> |
29 |
> I can only report that I've built a 2.6.33-gentoo kernel with |
30 |
> the device (sensors) Winbond W83627EHF/EF/EHG/EG |
31 |
> built in (not just a module), then ran sensors-detect |
32 |
> and now, xsensor works just fine (on a Phenom-II) |
33 |
|
34 |
In my version of 2.6.33-gentoo I don't see that as a choice in |
35 |
make menuconfig... none of the winbond lines match what you show |
36 |
above. The last one below is closest and as you see I have built it |
37 |
in. |
38 |
|
39 |
| | < > Winbond W83781D, W83782D, W83783S, Asus AS99127F | | |
40 |
| | < > Winbond W83791D | | |
41 |
| | < > Winbond W83792D | | |
42 |
| | < > Winbond W83793 | | |
43 |
| | < > Winbond W83L785TS-S | | |
44 |
| | < > Winbond W83L786NG, W83L786NR | | |
45 |
| | <*> Winbond W83627HF, W83627THF, W83637HF, W83687THF, W83697HF | | |
46 |
| | <*> Winbond W83627EHF/EHG/DHG, W83667HG |
47 |
|
48 |
But as you can see I've built in the last two. |
49 |
|
50 |
After installing that kernel and reboot |
51 |
|
52 |
The tail of: |
53 |
sensors-detect |
54 |
|
55 |
[...] |
56 |
|
57 |
Now follows a summary of the probes I have just done. |
58 |
Just press ENTER to continue: |
59 |
|
60 |
Driver `w83627hf': |
61 |
* ISA bus, address 0x290 |
62 |
Chip `Winbond W83627THF/THG Super IO Sensors' (confidence: 9) |
63 |
|
64 |
Warning: the required module w83627hf is not currently installed |
65 |
on your system. If it is built into the kernel then it's OK. |
66 |
Otherwise, check http://www.lm-sensors.org/wiki/Devices for |
67 |
driver availability. |
68 |
|
69 |
No modules to load, skipping modules configuration. |
70 |
|
71 |
Unloading i2c-dev... OK |
72 |
|
73 |
And following with: |
74 |
|
75 |
# sensors |
76 |
|
77 |
No sensors found! |
78 |
Make sure you loaded all the kernel drivers you need. |
79 |
Try sensors-detect to find out which these are. |
80 |
|
81 |
------- --------- ---=--- --------- -------- |
82 |
|
83 |
What motheboard are you running: |
84 |
|
85 |
Here is what `lshw', followed `hwinfo' had to say about my motherboard |
86 |
Or at least I think thats what this output is: |
87 |
|
88 |
from lswh: |
89 |
reader |
90 |
description: Desktop Computer |
91 |
product: MS-6728 |
92 |
vendor: MICRO-STAR INC. |
93 |
version: 2.00 |
94 |
serial: 00000000 |
95 |
width: 32 bits |
96 |
capabilities: smbios-2.3 dmi-2.3 smp-1.4 smp |
97 |
configuration: chassis=desktop cpus=1 |
98 |
*-core |
99 |
description: Motherboard |
100 |
product: MS-6728 |
101 |
vendor: MICRO-STAR INC. |
102 |
physical id: 0 |
103 |
version: 2.00 |
104 |
serial: 00000000 |
105 |
*-firmware |
106 |
description: BIOS |
107 |
vendor: American Megatrends Inc. |
108 |
physical id: 0 |
109 |
version: V3.A (09/29/2004) |
110 |
size: 64KiB |
111 |
capacity: 448KiB |
112 |
capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int17printer int10video acpi usb agp ls120boot zipboot biosbootspecification |
113 |
|
114 |
------- --------- ---=--- --------- -------- |
115 |
from hwinfo: |
116 |
|
117 |
01: None 00.0: 10105 BIOS |
118 |
[Created at bios.190] |
119 |
Unique ID: rdCR.lZF+r4EgHp4 |
120 |
Hardware Class: bios |
121 |
BIOS Keyboard LED Status: |
122 |
Scroll Lock: off |
123 |
Num Lock: on |
124 |
Caps Lock: off |
125 |
Serial Port 0: 0x3f8 |
126 |
Serial Port 1: 0x3e8 |
127 |
Parallel Port 0: 0x378 |
128 |
Base Memory: 639 kB |
129 |
PnP BIOS: @@@0000 |
130 |
MP spec rev 1.4 info: |
131 |
OEM id: "INTEL" |
132 |
Product id: "I865G/GE/PE" |
133 |
1 CPUs (0 disabled) |
134 |
BIOS32 Service Directory Entry: 0xfdb60 |
135 |
SMBIOS Version: 2.3 |
136 |
BIOS Info: #0 |
137 |
Vendor: "American Megatrends Inc." |
138 |
Version: "V3.A" |
139 |
Date: "09/29/2004" |
140 |
Start Address: 0xf0000 |
141 |
ROM Size: 512 kB |
142 |
Features: 0x0137000000006fcbde90 |
143 |
ISA supported |
144 |
PCI supported |
145 |
PnP supported |
146 |
APM supported |
147 |
BIOS flashable |
148 |
BIOS shadowing allowed |
149 |
ESCD supported |
150 |
CD boot supported |
151 |
Selectable boot supported |
152 |
BIOS ROM socketed |
153 |
EDD spec supported |
154 |
360kB Floppy supported |
155 |
1.2MB Floppy supported |
156 |
720kB Floppy supported |
157 |
2.88MB Floppy supported |
158 |
Print Screen supported |
159 |
8042 Keyboard Services supported |
160 |
Printer Services supported |
161 |
CGA/Mono Video supported |
162 |
ACPI supported |
163 |
USB Legacy supported |
164 |
AGP supported |
165 |
LS-120 boot supported |
166 |
ATAPI ZIP boot supported |
167 |
BIOS Boot Spec supported |
168 |
System Info: #1 |
169 |
Manufacturer: "MICRO-STAR INC." |
170 |
Product: "MS-6728" |
171 |
Version: "2.00" |
172 |
Serial: "00000000" |
173 |
UUID: undefined |
174 |
Wake-up: 0x04 (Modem Ring) |
175 |
Board Info: #2 |
176 |
Manufacturer: "MICRO-STAR INC." |
177 |
Product: "MS-6728" |
178 |
Version: "2.00" |
179 |
Serial: "00000000" |