| 1 |
Bob Sanders wrote: |
| 2 |
> On Sun, 18 Jun 2006 14:13:44 -0400 |
| 3 |
> sean <tech.junk@×××××××.net> wrote: |
| 4 |
> |
| 5 |
>> I am trying to get my recently built system to recognize my Adaptec |
| 6 |
>> 29160 configured on the system. |
| 7 |
>> I have SCSI built into the kernel, here is the dmesg statement, |
| 8 |
>> SCSI subsystem initialized, |
| 9 |
> |
| 10 |
> Do you have SCSI Transport Attributes ---> Parallel SCSI (SPI) Transport Attributes |
| 11 |
> turned on as either a module or loaded? |
| 12 |
> |
| 13 |
>> I can see my sata drive, which from what I read, scsi needs to be |
| 14 |
>> working for sata access, |
| 15 |
> |
| 16 |
> SATA doesn't need specific attributes unless it's really a SAS interface. |
| 17 |
> |
| 18 |
> |
| 19 |
>> but there is nothing in dmesg about my scsi |
| 20 |
>> card coming to life, and so I cannot see my cd burner and iomega jaz |
| 21 |
>> drive that hang off it. |
| 22 |
>> |
| 23 |
> |
| 24 |
> Should only need, under SCSI devices support --> SCSI disk, SCSI CDROM, |
| 25 |
> the previously mentioned parallel Transport, under low-level drivers --> |
| 26 |
> Adaptec AIC7xxx (aka New driver), SATA support, and the SATA chipset driver. |
| 27 |
> The rest is pretty much wasted space. |
| 28 |
> |
| 29 |
> Bob |
| 30 |
> - |
| 31 |
|
| 32 |
Thanks Bob, |
| 33 |
|
| 34 |
Things are improving, but still not over the top yet. |
| 35 |
As you can see below the dmesg shows things starting to light up... |
| 36 |
I am able to see the scsi cdrw and the jaz drive. |
| 37 |
Tried mounting the jaz drive but as expected it failed, the format of |
| 38 |
the unit cartridge is UFS. But it at least saw it, assigned it, and |
| 39 |
tried to mount when I manually tried. |
| 40 |
|
| 41 |
However the scsi cdrw is still not working. |
| 42 |
Again, as you can see it dmesg shows the device. However it is not |
| 43 |
assigning it a dev. |
| 44 |
The sr0 assignment you see listed is for my sata dvd unit, which is able |
| 45 |
to mount when I tested it. |
| 46 |
Are you, or anyone, able to offer any other suggestions? |
| 47 |
|
| 48 |
Thanks |
| 49 |
Sean |
| 50 |
|
| 51 |
----------------------------------------------------------------------- |
| 52 |
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 |
| 53 |
<Adaptec 29160 Ultra160 SCSI adapter> |
| 54 |
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs |
| 55 |
|
| 56 |
Vendor: PLEXTOR Model: CD-R PX-W4012S Rev: 1.01 |
| 57 |
Type: CD-ROM ANSI SCSI revision: 02 |
| 58 |
target0:0:1: Beginning Domain Validation |
| 59 |
target0:0:1: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) |
| 60 |
target0:0:1: Domain Validation skipping write tests |
| 61 |
target0:0:1: Ending Domain Validation |
| 62 |
Vendor: iomega Model: jaz 1GB Rev: J.83 |
| 63 |
Type: Direct-Access ANSI SCSI revision: 02 |
| 64 |
target0:0:4: Beginning Domain Validation |
| 65 |
target0:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) |
| 66 |
target0:0:4: Domain Validation skipping write tests |
| 67 |
target0:0:4: Ending Domain Validation |
| 68 |
libata version 1.20 loaded. |
| 69 |
SCSI device sda: 2091050 512-byte hdwr sectors (1071 MB) |
| 70 |
sda: Write Protect is off |
| 71 |
sda: Mode Sense: 39 00 10 08 |
| 72 |
SCSI device sda: drive cache: write back w/ FUA |
| 73 |
SCSI device sda: 2091050 512-byte hdwr sectors (1071 MB) |
| 74 |
sda: Write Protect is off |
| 75 |
sda: Mode Sense: 39 00 10 08 |
| 76 |
SCSI device sda: drive cache: write back w/ FUA |
| 77 |
sda: sda1 |
| 78 |
sd 0:0:4:0: Attached scsi removable disk sda |
| 79 |
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray |
| 80 |
sr 0:0:1:0: Attached scsi CD-ROM sr0 |
| 81 |
sr 0:0:1:0: Attached scsi generic sg0 type 5 |
| 82 |
sd 0:0:4:0: Attached scsi generic sg1 type 0 |
| 83 |
-- |
| 84 |
gentoo-user@g.o mailing list |
Archives