Gentoo Archives: gentoo-user

From: Volker Armin Hemmann <volkerarmin@××××××××××.com>
To: gentoo-user@l.g.o
Subject: Re: [gentoo-user] smartctrl drive error @60%
Date: Wed, 25 Jun 2014 16:55:34
Message-Id: 53AAFEEE.7020508@googlemail.com
In Reply to: Re: [gentoo-user] smartctrl drive error @60% by Dale
1 Am 25.06.2014 09:49, schrieb Dale:
2 > thegeezer wrote:
3 >> this is pretty bad. enough to really go and get a replacement asap,
4 >> and turn that disk off if you can. the self test stops at the first
5 >> error it comes to and in this case it is LBA#2905482560 for
6 >> calculation of where the error is check out the smartcl [1] site which
7 >> will help you to mark the block bad though the data that was in that
8 >> block is probably lost forever. i'd also suggest you run # smartctl -a
9 >> /dev/sdc and paste the results here. the crucial rows are 196/197 the
10 >> reallocated sector counts and pending sector counts. they show how
11 >> many blocks have been reallocated, and also how many are pending. this
12 >> will give you a scaling factor, at the moment you are in trouble, if
13 >> these figures are very high you are in very high trouble, if they are
14 >> low you are in low trouble. [1]
15 >> http://smartmontools.sourceforge.net/badblockhowto.html
16 > Here is the output:
17 >
18 > root@fireball / # smartctl -a /dev/sdc
19 > smartctl 6.1 2013-03-16 r3800 [x86_64-linux-3.14.0-gentoo] (local build)
20 > Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
21 >
22 > === START OF INFORMATION SECTION ===
23 > Model Family: Seagate Barracuda 7200.14 (AF)
24 > Device Model: ST3000DM001-9YN166
25 > Serial Number: Z1F0PKT5
26 > LU WWN Device Id: 5 000c50 04d79e15c
27 > Firmware Version: CC4C
28 > User Capacity: 3,000,592,982,016 bytes [3.00 TB]
29 > Sector Sizes: 512 bytes logical, 4096 bytes physical
30 > Rotation Rate: 7200 rpm
31 > Device is: In smartctl database [for details use: -P show]
32 > ATA Version is: ATA8-ACS T13/1699-D revision 4
33 > SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
34 > Local Time is: Wed Jun 25 02:46:39 2014 CDT
35 >
36 > ==> WARNING: A firmware update for this drive is available,
37 > see the following Seagate web pages:
38 > http://knowledge.seagate.com/articles/en_US/FAQ/207931en
39 > http://knowledge.seagate.com/articles/en_US/FAQ/223651en
40 >
41 > SMART support is: Available - device has SMART capability.
42 > SMART support is: Enabled
43 >
44 > === START OF READ SMART DATA SECTION ===
45 > SMART overall-health self-assessment test result: PASSED
46 >
47 > General SMART Values:
48 > Offline data collection status: (0x00) Offline data collection activity
49 > was never started.
50 > Auto Offline Data Collection:
51 > Disabled.
52 > Self-test execution status: ( 118) The previous self-test completed
53 > having
54 > the read element of the test failed.
55 > Total time to complete Offline
56 > data collection: ( 584) seconds.
57 > Offline data collection
58 > capabilities: (0x73) SMART execute Offline immediate.
59 > Auto Offline data collection
60 > on/off support.
61 > Suspend Offline collection upon new
62 > command.
63 > No Offline surface scan supported.
64 > Self-test supported.
65 > Conveyance Self-test supported.
66 > Selective Self-test supported.
67 > SMART capabilities: (0x0003) Saves SMART data before entering
68 > power-saving mode.
69 > Supports SMART auto save timer.
70 > Error logging capability: (0x01) Error logging supported.
71 > General Purpose Logging supported.
72 > Short self-test routine
73 > recommended polling time: ( 1) minutes.
74 > Extended self-test routine
75 > recommended polling time: ( 340) minutes.
76 > Conveyance self-test routine
77 > recommended polling time: ( 2) minutes.
78 > SCT capabilities: (0x3085) SCT Status supported.
79 >
80 > SMART Attributes Data Structure revision number: 10
81 > Vendor Specific SMART Attributes with Thresholds:
82 > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
83 > UPDATED WHEN_FAILED RAW_VALUE
84 > 1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail
85 > Always - 234421760
86 > 3 Spin_Up_Time 0x0003 092 092 000 Pre-fail
87 > Always - 0
88 > 4 Start_Stop_Count 0x0032 100 100 020 Old_age
89 > Always - 33
90 > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
91 > Always - 0
92 > 7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail
93 > Always - 99909120
94 > 9 Power_On_Hours 0x0032 082 082 000 Old_age
95 > Always - 16379
96 > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
97 > Always - 0
98 > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age
99 > Always - 34
100 > 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age
101 > Always - 0
102 > 184 End-to-End_Error 0x0032 100 100 099 Old_age
103 > Always - 0
104 > 187 Reported_Uncorrect 0x0032 100 100 000 Old_age
105 > Always - 0
106 > 188 Command_Timeout 0x0032 100 100 000 Old_age
107 > Always - 0 0 0
108 > 189 High_Fly_Writes 0x003a 100 100 000 Old_age
109 > Always - 0
110 > 190 Airflow_Temperature_Cel 0x0022 069 063 045 Old_age
111 > Always - 31 (Min/Max 26/33)
112 > 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age
113 > Always - 0
114 > 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
115 > Always - 9
116 > 193 Load_Cycle_Count 0x0032 093 093 000 Old_age
117 > Always - 14284
118 > 194 Temperature_Celsius 0x0022 031 040 000 Old_age
119 > Always - 31 (0 17 0 0 0)
120 > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age
121 > Always - 104
122 > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
123 > Offline - 104
124 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
125 > Always - 0
126 > 240 Head_Flying_Hours 0x0000 100 253 000 Old_age
127 > Offline - 15955h+37m+28.932s
128 > 241 Total_LBAs_Written 0x0000 100 253 000 Old_age
129 > Offline - 52221690631887
130 > 242 Total_LBAs_Read 0x0000 100 253 000 Old_age
131 > Offline - 74848968465606
132 >
133 > SMART Error Log Version: 1
134 > No Errors Logged
135 >
136 > SMART Self-test log structure revision number 1
137 > Num Test_Description Status Remaining
138 > LifeTime(hours) LBA_of_first_error
139 > # 1 Extended offline Completed: read failure 60%
140 > 16365 2905482560
141 > # 2 Extended offline Completed: read failure 60%
142 > 16352 2905482560
143 > # 3 Extended offline Completed without error 00%
144 > 8044 -
145 > # 4 Extended offline Completed without error 00%
146 > 3121 -
147 > # 5 Extended offline Completed without error 00%
148 > 1548 -
149 > # 6 Short offline Completed without error 00%
150 > 1141 -
151 > # 7 Extended offline Completed without error 00%
152 > 719 -
153 > # 8 Extended offline Completed without error 00%
154 > 525 -
155 > # 9 Short offline Completed without error 00%
156 > 516 -
157 > #10 Extended offline Completed without error 00%
158 > 18 -
159 > #11 Extended offline Completed without error 00%
160 > 5 -
161 > #12 Short offline Completed without error 00%
162 > 0 -
163 >
164 > SMART Selective self-test log data structure revision number 1
165 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
166 > 1 0 0 Not_testing
167 > 2 0 0 Not_testing
168 > 3 0 0 Not_testing
169 > 4 0 0 Not_testing
170 > 5 0 0 Not_testing
171 > Selective self-test flags (0x0):
172 > After scanning selected spans, do NOT read-scan remainder of disk.
173 > If Selective self-test is pending on power-up, resume after 0 minute delay.
174 >
175 > root@fireball / #
176 >
177 > Does that help shed any light on this situation? If you need more
178 > info, just let me know. Off to newegg. BRB
179 >
180 > Dale
181 >
182 > :-) :-)
183 >
184
185 so without looking that drive up - you are using a desktop part for
186 non-stop setup?

Replies

Subject Author
Re: [gentoo-user] smartctrl drive error @60% Rich Freeman <rich0@g.o>
Re: [gentoo-user] smartctrl drive error @60% Dale <rdalek1967@×××××.com>